参数资料
| 型号： | AD7875LNZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 15/28页 |
| 文件大小： | 0K |
| 描述： | IC ADC 12BIT SAMPLING 5V 24-DIP |
| 产品变化通告： | Product Discontinuance 27/Oct/2011 |
| 标准包装： | 1 |
| 位数： | 12 |
| 采样率（每秒）： | 100k |
| 数据接口： | 串行，并联 |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 95mW |
| 电压电源： | 双 ± |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 24-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 24-PDIP |
| 包装： | 管件 |
| 输入数目和类型： | 1 个单端，单极 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
AD7870/AD7875/AD7876
Rev. C | Page 22 of 2
8
APPLICATIONS INFORMATION
Good printed circuit board (PCB) layout is as important as
the overall circuit design itself in achieving high speed analog-
to-digital performance. The designer has to be conscious of
noise both in the ADC itself and in the preceding analog
circuitry. Switching mode power supplies are not recommended
because the switching spikes feed through to the comparator
causing noisy code transitions. Other causes of concern are
ground loops and digital feedthrough from microprocessors.
These are factors which influence any ADC, and a proper
PCB layout which minimizes these effects is essential for best
performance.
LAYOUT HINTS
Ensure that the layout for the printed circuit board has the
digital and analog signal lines separated as much as possible.
Take care not to run any digital track alongside an analog signal
track. Guard (screen) the analog input with AGND.
Establish a single point analog ground (star ground) separate
from the logic system ground at the AGND pin or as close
as possible to the ADC. Connect all other grounds and the
AD7870/AD7875/AD7876 DGND to this single analog
ground point. Do not connect any other digital grounds to
this analog ground point.
Low impedance analog and digital power supply common
returns are essential to low noise operation of the ADC, so
make the foil width for these tracks as wide as possible. The
use of ground planes minimizes impedance paths and also
guards the analog circuitry from digital noise. The circuit
layout has both analog and digital ground planes which are
kept separated and only joined together at the AD7870/
AD7875/AD7876 AGND pin.
NOISE
Keep the input signal leads to VIN and signal return leads from
AGND as short as possible to minimize input noise coupling.
In applications where this is not possible, use a shielded cable
between the source and the ADC. Reduce the ground circuit
impedance as much as possible since any potential difference
in grounds between the signal source and the ADC appears as
an error voltage in series with the input signal.
相关PDF资料 |
PDF描述 |
|---|---|
| AD7877WACPZ-REEL7 | IC CTRLR TOUCH SCREEN 32LFCSP |
| AD7878KPZ | IC ADC 12BIT W/DSP INT 28-PLCC |
| AD7880CR | IC ADC 12BIT MONO LP 24-SOIC |
| AD7884BQ | IC ADC 16BIT SAMPLING HS 40-CDIP |
| AD7886JD | IC ADC 12BIT SAMPLING HS 28-CDIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7875LNZ1 | 制造商:AD 制造商全称:Analog Devices 功能描述:LC2MOS Complete, 12-Bit, 100 kHz, Sampling ADCs |
| AD7875LP | 制造商:Rochester Electronics LLC 功能描述:12 BIT SAMPLING ADC IC - Bulk 制造商:Analog Devices 功能描述: |
| AD7875LP-REEL | 制造商:AD 制造商全称:Analog Devices 功能描述:LC2MOS Complete, 12-Bit, 100 kHz, Sampling ADCs |
| AD7875LPZ | 功能描述:IC ADC 12BIT SAMPLING 5V 28-PLCC RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:- 位数:14 采样率（每秒）:83k 数据接口:串行，并联 转换器数目:1 功率耗散（最大）:95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP（0.600"，15.24mm） 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端，双极 |
| AD7875LPZ1 | 制造商:AD 制造商全称:Analog Devices 功能描述:LC2MOS Complete, 12-Bit, 100 kHz, Sampling ADCs |
发布紧急采购，3分钟左右您将得到回复。