- 您现在的位置：买卖IC网 > PDF目录9713 > AD7879-1WARUZ-RL (Analog Devices Inc)IC ADC 12BIT CTRLR TOUCH 16TSSOP PDF资料下载
参数资料
| 型号： | AD7879-1WARUZ-RL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 11/41页 |
| 文件大小： | 0K |
| 描述： | IC ADC 12BIT CTRLR TOUCH 16TSSOP |
| 标准包装： | 2,500 |
| 类型： | 电阻 |
| 触摸面板接口： | 4 线 |
| 输入数/键： | 1 TSC |
| 分辨率（位）： | 12 b |
| 评估套件： | * |
| 数据接口： | I²C，串行 |
| 数据速率/采样率 (SPS，BPS)： | 105k |
| 电压基准： | 内部 |
| 电源电压： | 1.6 V ~ 3.6 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 16-TSSOP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页
AD7879/AD7889
Rev. C | Page 18 of 40
AUX/VBAT/GPIO PIN
The AUX/VBAT/GPIO pin on the AD7879/AD7889 can be
programmed as an auxiliary input to the ADC, as a battery
monitoring input, or as a general-purpose digital input/output.
To select the auxiliary measurement, set the ADC channel
address to 011 (Bits[14:12] in Control Register 1, Address 0x01).
To select a battery measurement, set the ADC channel address
to 010. To select the GPIO function, set Bit 13 in Control
Register 2 (Address 0x02) to 1.
AUXILIARY INPUT
The AD7879/AD7889 have an auxiliary analog input, AUX.
When the auxiliary input function is selected, the signal on the
AUX pin (AUX/VBAT/GPIO) is connected directly to the ADC
input. This channel has a full-scale input range from 0 V to VCC.
The ADC channel address for AUX is 011 (Bits[14:12] in
Control Register 1, Address 0x01), and the result is stored in
the AUX/VBAT result register (Address 0x0C).
BATTERY INPUT
The AD7879/AD7889 can monitor battery voltages from 0.5 V
to 5 V when the BAT measurement is selected. Figure 28 shows
a block diagram of a battery voltage monitored through the VBAT
pin. The voltage to the VCC pin (VCC/REF) of the AD7879/AD7889
is maintained at the desired supply voltage via the dc-to-dc
converter, and the input to the converter is monitored. This
voltage on VBAT is divided by 4 internally, so that a 5 V battery
voltage is presented to the ADC as 1.25 V. To conserve power,
the divider circuit is on only during the sampling of a voltage on
VBAT. Note that the possible maximum input is 5 V.
The ADC channel address for VBAT is 010 (Bits[14:12] in
Control Register 1, Address 0x01), and the result is stored in
the AUX/VBAT result register (Address 0x0C).
ADC
0.125V TO 1.25V
SW
VBAT
VCC
12k
4k
DC-TO-DC
CONVERTER
BATTERY
0.5V TO 5V
07667-
028
Figure 28. Block Diagram of Battery Measurement Circuit
The maximum battery voltage that the AD7879/AD7889 can
measure changes when a different reference voltage is used. The
maximum voltage that is measurable is VCC × 4 because this
voltage gives a full-scale output from the ADC. The battery
voltage can be calculated using the following formula:
VBAT (V) = [(Register Value) × VCC × 4]/4095
LIMIT COMPARISON
The AUX measurement and the battery measurement can
be compared with high and low limits stored on chip. An
out-of-limit result generates an alarm output at the INT pin
(PENIRQ/INT/DAV) when the INT function is enabled. The
high limit for both channels is stored in the AUX/VBAT high
limit register (Address 0x04), and the low limit is stored in the
AUX/VBAT low limit register (Address 0x05).
After a measurement from either AUX or VBAT is taken, it
is compared with the high and low limits. The out-of-limit
comparison sets a status bit in Control Register 3. Separate
status bits for the high limit and the low limit indicate which
limit was exceeded. The interrupt sources can be masked by
clearing the corresponding enable bit in Control Register 3.
GPIO
The AD7879/AD7889 have one general-purpose logic input/
output pin, GPIO (AUX/VBAT/GPIO). To enable GPIO, set Bit
13 in Control Register 2 to 1. If this bit is set to 0, the
AUX/VBAT function is active on the pin. If the GPIO is not
enabled, the other GPIO configuration bits have no effect.
The GPIO data bit is Bit 12 in Control Register 2.
Direction (Bit 11, Control Register 2, Address 0x02)
Bit 11 sets the direction of the GPIO pin (AUX/VBAT/GPIO).
When GPIO DIR = 0, the pin is an output. Setting or clearing
the GPIO data bit (Bit 12 in Control Register 2) outputs a value
on the GPIO pin.
When GPIO DIR = 1, the pin is an input. An input value on the
GPIO pin sets or clears the GPIO data bit (Bit 12 in Control
Register 2). GPIO data register bits are read-only when GPIO
DIR = 1.
Polarity (Bit 10, Control Register 2, Address 0x02)
When GPIO POL = 0, the GPIO pin is active low. When GPIO
POL = 1, the GPIO pin is active high. How this bit affects the
GPIO operation also depends on the GPIO DIR bit.
If GPIO POL = 1 and GPIO DIR = 1, a 1 at the input pin sets
the corresponding GPIO data register bit to 1. A 0 at the input
pin clears the corresponding GPIO data bit to 0.
If GPIO POL = 1 and GPIO DIR = 0, a 1 in the GPIO data
register bit puts a 1 on the corresponding GPIO output pin. A 0
in the GPIO data register bit puts a 0 on the GPIO output pin.
If GPIO POL = 0 and GPIO DIR = 1, a 1 at the input pin sets
the corresponding GPIO data bit to 0. A 0 at the input pin clears
the corresponding GPIO data bit to 1.
If GPIO POL = 0 and GPIO DIR = 0, a 1 in the GPIO data
register bit puts a 0 on the corresponding GPIO output pin. A 0
in the GPIO data register bit puts a 1 on the GPIO output pin.
相关PDF资料 |
PDF描述 |
|---|---|
| AD7879-1WACPZ-RL | IC ADC 12BIT CTRLR TOUCH 16LFCSP |
| AD7879WARUZ-RL | IC ADC 12BIT CTLR TOUCH 16TSSOP |
| AD7889-1ACBZ-RL7 | IC ADC 12BIT CTRLR TOUCH 12WLCSP |
| AD7889ACBZ-RL | IC ADC 12BIT CTRLR TOUCH 12WLCSP |
| AD7889-1ACBZ-RL | IC ADC 12BIT CTRLR TOUCH 12WLCSP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7879-1WARUZ-RL7 | 功能描述:IC ADC 12BIT CTRLR TOUCH 16TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 触摸屏控制器 系列:- 标准包装:96 系列:- 类型:- 触摸面板接口:- 输入数/键:- 分辨率（位）:- 评估套件:* 数据接口:- 数据速率/采样率 (SPS，BPS):- 电压基准:- 电源电压:- 电流 - 电源:- 工作温度:- 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:带卷 (TR) |
| AD7879ACBZ-500R7 | 制造商:AD 制造商全称:Analog Devices 功能描述:Low Voltage Controller for Touch Screens |
| AD7879ACBZ-RL | 制造商:Analog Devices 功能描述: |
| AD7879ACPZ-500R7 | 制造商:Analog Devices 功能描述:TOUCH SCREEN CONTROLLER - Tape and Reel 制造商:Analog Devices 功能描述:ADC 12BIT 3.6V 105KSPS SPI 16LFCSP 制造商:Analog Devices 功能描述:ADC, 12BIT, 3.6V, 105KSPS, SPI, 16LFCSP 制造商:Analog Devices 功能描述:ADC, 12BIT, 3.6V, 105KSPS, SPI, 16LFCSP; Resolution (Bits):12bit; Sampling Rate:105kSPS; Digital IC Case Style:LFCSP; No. of Pins:16; Input Channel Type:Single Ended; Data Interface:SPI; Operating Temperature Min:-40C; Operating ;RoHS Compliant: Yes |
| AD7879ACPZ-RL | 功能描述:IC ADC 12BIT CTLR TOUCH 16LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 触摸屏控制器 系列:- 标准包装:96 系列:- 类型:- 触摸面板接口:- 输入数/键:- 分辨率（位）:- 评估套件:* 数据接口:- 数据速率/采样率 (SPS，BPS):- 电压基准:- 电源电压:- 电流 - 电源:- 工作温度:- 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。