- 您现在的位置：买卖IC网 > PDF目录10537 > AD7899ARZ-2 (Analog Devices Inc)IC ADC 14BIT 400KSPS 5V 28SOIC PDF资料下载
参数资料
| 型号： | AD7899ARZ-2 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 14/16页 |
| 文件大小： | 0K |
| 描述： | IC ADC 14BIT 400KSPS 5V 28SOIC |
| 标准包装： | 27 |
| 位数： | 14 |
| 采样率（每秒）： | 400k |
| 数据接口： | 并联 |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 125mW |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 28-SOIC W |
| 包装： | 管件 |
| 输入数目和类型： | 1 个差分，单极 |
| 配用： | EVAL-AD7899CBZ-ND - BOARD EVAL FOR AD7899 |
REV. A
AD7899
–7–
TERMINOLOGY
Signal to (Noise + Distortion) Ratio
This is the measured ratio of signal to (noise + distortion) at the
output of the A/D converter. The signal is the rms amplitude of
the fundamental. Noise is the rms sum of all nonfundamental
signals up to half the sampling frequency (fS/2), excluding dc.
The ratio is dependent upon the number of quantization levels
in the digitization process; the more levels, the smaller the quan-
tization noise. The theoretical signal to (noise + distortion) ratio
for an ideal N-bit converter with a sine wave input is given by:
Signal to (Noise + Distortion) = (6.02N + 1.76) dB
Thus for a 14-bit converter, this is 86.04 dB.
Total Harmonic Distortion
Total harmonic distortion (THD) is the ratio of the rms sum of
harmonics to the fundamental. For the AD7899 it is defined
as: THD dB
VVV
V
(
)
log
=
++
+
20
2
3
2
4
2
5
2
6
2
1
where V1 is the rms amplitude of the fundamental and V2, V3,
V4, and V5 are the rms amplitudes of the second through the
fifth harmonics.
Peak Harmonic or Spurious Noise
Peak harmonic or spurious noise is defined as the ratio of the
rms value of the next largest component in the ADC output
spectrum (up to fS/2 and excluding dc) to the rms value of the
fundamental. Normally, the value of this specification is deter-
mined by the largest harmonic in the spectrum, but for parts
where the harmonics are buried in the noise floor, it will be a
noise peak.
Intermodulation Distortion
With inputs consisting of sine waves at two frequencies, fa and
fb, any active device with nonlinearities will create distortion
products at sum and difference frequencies of mfa
± nfb where
m, n = 0, 1, 2, 3, etc. Intermodulation terms are those for which
neither m nor n are equal to zero. For example, the second order
terms include (fa + fb) and (fa – fb), while the third order terms
include (2fa + fb), (2fa – fb), (fa + 2fb) and (fa – 2fb).
The AD7899 is tested using two input frequencies. In this case, the
second and third order terms are of different significance. The
second order terms are usually distanced in frequency from the
original sine waves while the third order terms are usually at a
frequency close to the input frequencies. As a result, the second
and third order terms are specified separately. The calculation
of the intermodulation distortion is as per the THD speci-
fication where it is the ratio of the rms sum of the individual
distortion products to the rms amplitude of the fundamental
expressed in dBs.
Differential Nonlinearity
This is the difference between the measured and the ideal
1 LSB change between any two adjacent codes in the ADC.
Positive Gain Error (AD7899-1, AD7899-3)
This is the deviation of the last code transition (01 . . . 110 to
01 . . . 111) from the ideal 4
× VREF – 3/2 LSB (AD7899 at
± 10 V), 2 × V
REF – 3/2 LSB (AD7899 at
± 5 V range) or V
REF
– 3/2 LSB (AD7899 at
± 2.5 V range) after the Bipolar Offset
Error has been adjusted out.
Positive Gain Error (AD7899-2)
This is the deviation of the last code transition (11 . . . 110 to
11 . . . 111) from the ideal 2
× VREF – 3/2 LSB (AD7899 at
± 10 V), 2 × VREF – 3/2 LSB (AD7899 at 0 V to 5 V range) or
VREF – 3/2 LSB (AD7899 at 0 V to 2.5 V range) after the Uni-
polar Offset Error has been adjusted out.
Unipolar Offset Error (AD7899-2)
This is the deviation of the first code transition (00 . . . 00 to
00 . . . 01) from the ideal AGND +1/2 LSB
Bipolar Zero Error (AD7899-1, AD7899-2)
This is the deviation of the midscale transition (all 0s to all 1s)
from the ideal AGND – 1/2 LSB.
Negative Gain Error (AD7899-1, AD7899-3)
This is the deviation of the first code transition (10 . . . 000 to
10 . . . 001) from the ideal –4
× VREF + 1/2 LSB (AD7899 at
±10 V), –2 × VREF + 1/2 LSB (AD7899 at ±5 V range) or –VREF
+ 1/2 LSB (AD7899 at
±2.5 V range) after Bipolar Zero Error
has been adjusted out.
Track/Hold Acquisition Time
Track/Hold acquisition time is the time required for the output
of the track/hold amplifier to reach its final value, within
±1/2 LSB,
after the end of conversion (the point at which the track/hold
returns to track mode). It also applies to situations where there
is a step input change on the input voltage applied to the selected
VINA/VINB input of the AD7899. It means that the user must wait
for the duration of the track/hold acquisition time after the end
of conversion or after a step input change to VINA/VINB before
starting another conversion, to ensure that the part operates to
specification.
相关PDF资料 |
PDF描述 |
|---|---|
| HIN232ACBZ | IC 2DRVR/2RCVR RS232 5V 16-SOIC |
| VI-B4J-MX-F2 | CONVERTER MOD DC/DC 36V 75W |
| AD7356YRUZ | IC ADC DUAL 12BIT 5MSPS 16TSSOP |
| VI-B4J-MW | CONVERTER MOD DC/DC 36V 100W |
| HIN232IBZ | IC 2DRVR/2RCVR RS232 5V 16-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7899ARZ-2REEL | 功能描述:IC ADC 14BIT 400KSPS 5V 28SOIC RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
| AD7899ARZ-3 | 功能描述:IC ADC 14BIT 400KSPS 5V 28SOIC RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
| AD7899BR-1 | 功能描述:IC ADC 14BIT 400KSPS 5V 28-SOIC RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:- 位数:14 采样率（每秒）:83k 数据接口:串行，并联 转换器数目:1 功率耗散（最大）:95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP（0.600"，15.24mm） 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端，双极 |
| AD7899BR-1REEL | 制造商:Analog Devices 功能描述:ADC SGL SAR 400KSPS 14BIT PARALLEL 28SOIC W - Tape and Reel |
| AD7899BR-1REEL7 | 功能描述:IC ADC 14BIT 400KSPS 5V 28-SOIC RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 位数:12 采样率（每秒）:3M 数据接口:- 转换器数目:- 功率耗散（最大）:- 电压电源:- 工作温度:- 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-23-6 包装:带卷 (TR) 输入数目和类型:- |
发布紧急采购，3分钟左右您将得到回复。