- 您现在的位置：买卖IC网 > PDF目录10302 > AD7924WYRUZ-REEL7 (Analog Devices Inc)IC ADC 12BIT 4CH W/SEQ 16TSSOP PDF资料下载
参数资料
| 型号： | AD7924WYRUZ-REEL7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 7/32页 |
| 文件大小： | 0K |
| 描述： | IC ADC 12BIT 4CH W/SEQ 16TSSOP |
| 标准包装： | 1,000 |
| 位数： | 12 |
| 采样率（每秒）： | 1M |
| 数据接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 13.5mW |
| 电压电源： | 单电源 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 16-TSSOP |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 4 个单端，单极 |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
Data Sheet
AD7904/AD7914/AD7924
Rev. C | Page 15 of 32
CONTROL REGISTER
The control register of the AD7904/AD7914/AD7924 is a
12-bit, write-only register. Data is loaded from the DIN pin of
the AD7904/AD7914/AD7924 on the falling edge of SCLK. The
data is transferred on the DIN line at the same time that the
conversion result is read from the part. The data transferred on
the DIN line corresponds to the AD7904/AD7914/AD7924
configuration for the next conversion. This requires 16 serial
clocks for every data transfer. Only the information provided
on the first 12 falling clock edges (after the CS falling edge) is
loaded to the control register. MSB denotes the first bit in the
data stream. The bit functions are outlined in Table 8.
Table 7. Channel Selection
ADD1
ADD0
Analog Input Channel
0
VIN0
0
1
VIN1
1
0
VIN2
1
VIN3
Table 8. Control Register Bit Functions
MSB
LSB
11
10
9
8
7
6
5
4
3
2
1
0
WRITE
SEQ1
DONTC
ADD1
ADD0
PM1
PM0
SEQ0
DONTC
RANGE
CODING
Bit
Mnemonic
Description
11
WRITE
The value written to this bit determines whether the following 11 bits will be loaded to the control register. If this bit
is set to 1, the following 11 bits will be written to the control register; if this bit is set to 0, the remaining 11 bits are not
loaded to the control register, which remains unchanged.
10
SEQ1
The SEQ1 bit is used in conjunction with the SEQ0 bit to control the use of the sequencer function (see Table 10).
[9:8]
DONTC
Don’t care bits.
[7:6]
ADD1,
ADD0
The two address bits are loaded at the end of the present conversion sequence and select which analog input
channel is to be converted in the next serial transfer, or they may select the final channel in a consecutive sequence
as described in Table 10. The selected input channel is decoded as shown in Table 7. The address bits corresponding
to the conversion result are also output on DOUT prior to the 12 bits of data (see the Serial Interface section). The next
channel to be converted on will be selected by the mux on the 14th SCLK falling edge.
[5:4]
PM1, PM0
The two power management bits decode the mode of operation of the AD7904/AD7914/AD7924 as described in
3
SEQ0
The SEQ0 bit is used in conjunction with the SEQ1 bit to control the use of the sequencer function (see Table 10).
2
DONTC
Don’t care bit.
1
RANGE
This bit selects the analog input range to be used on the AD7904/AD7914/AD7924. If it is set to 0, the analog input
range will extend from 0 V to 2 × REFIN. If it is set to 1, the analog input range will extend from 0 V to REFIN (for the next
conversion). For the 0 V to 2 × REFIN input range, VDD = 4.75 V to 5.25 V.
0
CODING
This bit selects the type of output coding that the AD7904/AD7914/AD7924 will use for the conversion result. If this
bit is set to 0, the output coding for the part will be twos complement. If this bit is set to 1, the output coding from
the part will be straight binary (for the next conversion).
Table 9. Power Mode Selection
PM1
PM0
Mode
Description
1
Normal
operation
In normal operation mode, the AD7904/AD7914/AD7924 remain in full power mode regardless of
the status of any of the logic inputs. This mode allows the fastest possible throughput rate from the
AD7904/AD7914/AD7924.
1
0
Full
shutdown
In full shutdown mode, the AD7904/AD7914/AD7924 are in full shutdown with all circuitry on the
device powering down. The AD7904/AD7914/AD7924 retain the information in the control register
while in full shutdown. The part remains in full shutdown until these bits are changed.
0
1
Auto
shutdown
In auto shutdown mode, the AD7904/AD7914/AD7924 automatically enter full shutdown mode at the
end of each conversion when the control register is updated. Wake-up time from full shutdown is 1 μs;
the user should ensure that 1 μs has elapsed before attempting to perform a valid conversion on the
part in this mode.
0
Invalid
Invalid selection. This configuration is not allowed.
相关PDF资料 |
PDF描述 |
|---|---|
| VE-BTX-MW-S | CONVERTER MOD DC/DC 5.2V 100W |
| AD7705BRU-REEL | IC ADC 16BIT 2CH 16-TSSOP T/R |
| MS27497E10B99SB | CONN RCPT 7POS WALL MNT W/SCKT |
| VE-BTW-MW-S | CONVERTER MOD DC/DC 5.5V 100W |
| AD7322BRUZ-REEL | IC ADC 12BIT+SAR 2CHAN 14-TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7927 | 制造商:AD 制造商全称:Analog Devices 功能描述:8-Channel, 200 kSPS, 12-Bit ADC with Sequencer in 20-Lead TSSOP |
| AD7927BRU | 功能描述:IC ADC 12BIT 8CH 200KSPS 20TSSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| AD7927BRU-REEL | 制造商:Analog Devices 功能描述:ADC Single SAR 200ksps 12-bit Serial 20-Pin TSSOP T/R 制造商:Analog Devices 功能描述:ADC SGL SAR 200KSPS 12-BIT SERL 20TSSOP - Tape and Reel |
| AD7927BRU-REEL7 | 制造商:Analog Devices 功能描述:ADC Single SAR 200ksps 12-bit Serial 20-Pin TSSOP T/R |
| AD7927BRUZ | 功能描述:IC ADC 12BIT 8CH 200KSPS 20TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
发布紧急采购，3分钟左右您将得到回复。