参数资料
| 型号： | AD7980ARMZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 11/28页 |
| 文件大小： | 0K |
| 描述： | ADC 16BIT 1MSPS LP 10-MSOP |
| 标准包装： | 1 |
| 系列： | PulSAR® |
| 位数： | 16 |
| 采样率（每秒）： | 1M |
| 数据接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 10mW |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 10-MSOP |
| 包装： | 管件 |
| 输入数目和类型： | 1 个伪差分，单极 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
Data Sheet
AD7980
Rev. C | Page 19 of 28
CS MODE 4-WIRE, WITHOUT BUSY INDICATOR
This mode is usually used when multiple AD7980s are
connected to an SPI-compatible digital host.
A connection diagram example using two AD7980s is shown in
Figure 35, and the corresponding timing is given in Figure 36.
With SDI high, a rising edge on CNV initiates a conversion,
selects the CS mode, and forces SDO to high impedance. In this
mode, CNV must be held high during the conversion phase and
the subsequent data readback (if SDI and CNV are low, SDO is
driven low). Prior to the minimum conversion time, SDI can be
used to select other SPI devices, such as analog multiplexers,
but SDI must be returned high before the minimum conversion
time elapses and then held high for the maximum conversion
time to avoid the generation of the busy signal indicator.
When the conversion is complete, the AD7980 enters the
acquisition phase and powers down. Each ADC result can be
read by bringing its SDI input low, which consequently outputs
the MSB onto SDO. The remaining data bits are then clocked by
subsequent SCK falling edges. The data is valid on both SCK
edges. Although the rising edge can be used to capture the data,
a digital host using the SCK falling edge allows a faster reading
rate provided it has an acceptable hold time. After the 16th SCK
falling edge or when SDI goes high, whichever is earlier, SDO
returns to high impedance and another AD7980 can be read.
06392-
019
DIGITAL HOST
CONVERT
CS2
CS1
CLK
DATA IN
AD7980 SDO
SDI
CNV
SCK
AD7980 SDO
SDI
CNV
SCK
Figure 35. 4-Wire CS Mode Without Busy Indicator Connection Diagram
06392-
020
tCONV
tCYC
AQUISITION
tACQ
tSCK
tSCKH
tSCKL
CONVERSION
SCK
CNV
tSSDICNV
tHSDICNV
SDO
D15
D13
D14
D1
D0
D15
D14
D1
D0
tHSDO
tEN
1
2
3
14
15
16
17
18
30
31
32
tDSDO
tDIS
SDI(CS1)
SDI(CS2)
Figure 36. 4-Wire CS Mode Without Busy Indicator Serial Interface Timing
相关PDF资料 |
PDF描述 |
|---|---|
| AD7982BCPZ-RL | IC ADC 18BIT 1MSPS PULSAR 10LFCS |
| AD7983BCPZ-RL7 | IC ADC 16BIT 1.33MSPS 10LFCSP |
| AD7984BCPZ-RL7 | IC ADC 18BIT 1.33MSPS 10LFCSP |
| AD7985BCPZ-RL7 | IC ADC 16B 2.5MSPS PULSR 20LFCSP |
| AD7986BCPZ-RL7 | IC ADC 18BIT 2MSPS SAR 20LFCSP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7980ARMZ | 制造商:Analog Devices 功能描述:; Leaded Process Compatible:Yes; Peak Re |
| AD7980ARMZRL7 | 功能描述:ADC 16BIT 1MSPS 2.5LSB 10-MSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:PulSAR® 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
| AD7980ARMZ-RL7 | 制造商:Analog Devices 功能描述:- Tape and Reel |
| AD7980BCPZ-R2 | 制造商:Analog Devices 功能描述:- Tape and Reel |
| AD7980BCPZ-RL | 功能描述:IC ADC 16BIT 1MSPS SAR 10LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:PulSAR® 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
发布紧急采购，3分钟左右您将得到回复。