- 您现在的位置：买卖IC网 > PDF目录10330 > AD7992BRMZ-0REEL (Analog Devices Inc)IC ADC 12BIT 2CHAN I2C 10MSOP PDF资料下载
参数资料
| 型号： | AD7992BRMZ-0REEL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 18/29页 |
| 文件大小： | 0K |
| 描述： | IC ADC 12BIT 2CHAN I2C 10MSOP |
| 标准包装： | 3,000 |
| 位数： | 12 |
| 采样率（每秒）： | 79k |
| 数据接口： | I²C，串行 |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 2.2mW |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 10-MSOP |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 2 个单端，单极 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
AD7992
Rev. 0 | Page 24 of 28
ALERT/BUSY PIN
The ALERT/BUSY pin may be configured as an ALERT output
or BUSY output, as shown in Table 11.
SMBus ALERT
The AD7992 ALERT output is an SMBus interrupt line for
devices that want to trade their ability to master for an extra
pin. The AD7992 is a slave-only device and uses the SMBus
ALERT to signal the host device that it wants to talk. The
SMBus ALERT on the AD7992 is used as an out-of-conversion-
range indicator (a limit violation indicator).
The ALERT pin has an open-drain configuration that allows the
ALERT outputs of several AD7992s to be wire-AND’ed together
when the ALERT pin is active low. D0 of the configuration
register is used to set the active polarity of the ALERT output.
The power-up default is active low. The ALERT function can be
disabled or enabled by setting D2 of the configuration register
to 0 or 1, respectively.
The host device can process the ALERT interrupt and simul-
taneously access all SMBus ALERT devices through the alert
response address. Only the device that pulled the ALERT low
acknowledges the ARA (alert response address). If more than
one device pulls the ALERT pin low, the highest priority (lowest
address) device wins communication rights via standard I2C
arbitration during the slave address transfer.
The ALERT output becomes active when the value in the
conversion result register exceeds the value in the DATAHIGH
register or falls below the value in the DATALOW register for a
selected channel. It is reset when a write operation to the
configuration register sets D1 to a 1, or when the conversion
result returns N LSBs below or above the value stored in the
DATAHIGH register or DATALOW register, respectively. N is the
value in the hysteresis register (see the Limit Registers section).
The ALERT output requires an external pull-up resistor that
can be connected to a voltage different from VDD provided the
maximum voltage rating of the ALERT output pin is not
exceeded. The value of the pull-up resistor depends on the
application, but should be as large as possible to avoid excessive
sink currents at the ALERT output.
PLACING THE AD7992-1 INTO HIGH SPEED MODE
High speed mode communication commences after the master
addresses all devices connected to the bus with the master code,
00001XXX, to indicate that a high speed mode transfer is to
begin. No device connected to the bus is allowed to acknowl-
edge the high speed master code; therefore, the code is followed
by a not acknowledge (see Figure 30). The master must then
issue a repeated start followed by the device address with a R/W
bit. The selected device then acknowledges its address.
All devices continue to operate in high speed mode until the
master issues a STOP condition. When the STOP condition is
issued, the devices all return to fast mode.
THE ADDRESS SELECT (AS) PIN
The address select pin on the AD7992 is used to set the I2C
address for the AD7992 device. The AS pin can be tied to VDD,
to AGND, or left floating. The selection should be made as close
as possible to the AS pin; avoid having long tracks introducing
extra capacitance onto the pin. This is important for the float
selection, because the AS pin has to charge to a midpoint after
the start bit during the first address byte. Extra capacitance on
the AS pin increases the time taken to charge to the midpoint
and may cause an incorrect decision on the device address.
When the AS pin is left floating, the AD7992 can work with a
capacitive load up to 40 pF.
SDA
ACK. BY
AD7992
START BY
MASTER
HS-MODE MASTER CODE
SERIAL BUS ADDRESS BYTE
NACK
19
1
9
0
1
A2
A1
A0
X
1
0
SCL
0
A3
X
Sr
FAST MODE
HIGH SPEED MODE
03263-0-011
Figure 30. Placing the Part into High Speed Mode
相关PDF资料 |
PDF描述 |
|---|---|
| MS27468T17B99B | CONN HSG RCPT 23POS JAMNUT SCKT |
| MS3108A14S-2P | CONN PLUG 4POS RT ANG W/PINS |
| VE-24L-IU-S | CONVERTER MOD DC/DC 28V 200W |
| VI-2WB-MX-S | CONVERTER MOD DC/DC 95V 75W |
| MS27497E8C35S | CONN RCPT 6POS WALL MNT W/SCKT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7992BRMZ-1 | 功能描述:IC ADC 12BIT 2CHAN I2C 10-MSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
| AD7992BRMZ-1-R2 | 制造商:Analog Devices 功能描述: |
| AD7992BRMZ-1REEL | 功能描述:IC ADC 12BIT 2CHAN I2C 10MSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:2,500 系列:- 位数:16 采样率（每秒）:15 数据接口:MICROWIRE?，串行，SPI? 转换器数目:1 功率耗散（最大）:480µW 电压电源:单电源 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:38-WFQFN 裸露焊盘 供应商设备封装:38-QFN（5x7） 包装:带卷 (TR) 输入数目和类型:16 个单端，双极；8 个差分，双极 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| AD7993 | 制造商:AD 制造商全称:Analog Devices 功能描述:4-Channel, 12-/10-Bit ADCs with I2C Compatible Interface in 16-Lead TSSOP |
| AD7993-0 | 制造商:AD 制造商全称:Analog Devices 功能描述:4-Channel, 10- and 12-Bit ADCs with I2C Compatible Interface in 16-Lead TSSOP |
发布紧急采购，3分钟左右您将得到回复。