参数资料
| 型号： | AD7994BRUZ-1 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 20/32页 |
| 文件大小： | 0K |
| 描述： | IC ADC 12BIT 4CHAN I2C 16TSSOP |
| 标准包装： | 96 |
| 位数： | 12 |
| 采样率（每秒）： | 188k |
| 数据接口： | I²C，串行 |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 2.2mW |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 16-TSSOP |
| 包装： | 管件 |
| 输入数目和类型： | 4 个单端，单极 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
AD7993/AD7994
Rev. 0 | Page 27 of 32
ALERT/BUSY PIN
The ALERT/BUSY pin may be configured as an alert output or
busy output, as shown in Table 12.
SMBus ALERT
The AD7993/AD7994 alert output is an SMBus interrupt line
for devices that want to trade their ability to master for an extra
pin. The AD7993/AD7994 is a slave-only device and uses the
SMBus alert to signal the host device that it wants to talk. The
SMBus alert on the AD7993/AD7994 is used as an out-of-
conversion range indicator (a limit violation indicator).
The ALERT pin has an open-drain configuration that allows
the alert outputs of several AD7993/AD7994s to be wired-
AND’ed together when the ALERT pin is active low. D0 of the
configuration register is used to set the active polarity of the
ALERT output. The power-up default is active low. The ALERT
function can be enabled or disabled by setting D2 of the
configuration register to 1 or 0, respectively.
The host device can process the ALERT interrupt and
simultaneously access all SMBus ALERT devices through the
alert response address. Only the device that pulled the ALERT
low acknowledges the ARA (alert response address). If more
than one device pulls the ALERT pin low, the highest priority
(lowest address) device wins communication rights via standard
I2C arbitration during the slave address transfer.
The ALERT output becomes active when the value in the
conversion result register exceeds the value in the DATAHIGH
register or falls below the value in the DATALOW register. It is
reset when a write operation to the configuration register sets
D1 and D0 to a 1, or when the conversion result returns N LSB
below or above the value stored in the DATAHIGH register or
DATALOW register, respectively. N is the value in the hysteresis
register (see the Limit Registers section).
The ALERT output requires an external pull-up resistor that
can be connected to a voltage different from VDD provided the
maximum voltage rating of the ALERT output pin is not
exceeded. The value of the pull-up resistor depends on the
application, but should be as large as possible to avoid excessive
sink currents at the ALERT output.
BUSY
When the ALERT/BUSY pin is configured as a BUSY output,
the pin is used to indicate when a conversion is taking place.
The polarity of the BUSY pin is programmed through bit D0 in
the configuration register.
PLACING THE AD7993-1/AD7994-1 INTO HIGH
SPEED MODE
High speed mode communication commences after the master
addresses all devices connected to the bus with the master code,
00001XXX, to indicate that a high speed mode transfer is to
begin. No device connected to the bus is allowed to acknowl-
edge the high speed master code; therefore, the code is followed
by a not acknowledge (see Figure 31). The master must then
issue a repeated start followed by the device address with a R/W
bit. The selected device then acknowledges its address.
All devices continue to operate in high speed mode until the
master issues a stop condition. When the stop condition is
issued, the devices all return to fast mode.
THE ADDRESS SELECT (AS) PIN
The address select pin on the AD7993/AD7994 is used to set
the I2C address for the AD7993/AD7994 device. The AS pin
can be tied to VDD, to AGND, or left floating. The selection
should be made as close as possible to the AS pin; avoid having
long tracks introducing extra capacitance on the pin. This is
important for the float selection, because the AS pin has to
charge to a midpoint after the start bit during the first address
byte. Extra capacitance on the AS pin increases the time taken
to charge to the midpoint and may cause an incorrect decision
on the device address. When the AS pin is left floating, the
AD7993/AD7994 can work with a capacitive load up to 40 pF.
SDA
ACK. BY
AD7993/AD7994
START BY
MASTER
HS MODE MASTER CODE
SERIAL BUS ADDRESS BYTE
NACK
19
1
9
0
1
A2
A1
A0
X
1
0
SCL
0
A3
X
Sr
FAST MODE
HIGH SPEED MODE
03472-0-031
Figure 31. Placing the Part into High Speed Mode
相关PDF资料 |
PDF描述 |
|---|---|
| AD800-52BR | IC CLK\DATA RECOVERY PLL 20-SOIC |
| AD809BR-REEL7 | IC SYNTH FREQ 155.52MHZ 16-SOIC |
| AD8300AR | IC DAC 12BIT 3V SRL-IN 8-SOIC |
| AD8522AR | IC DAC 12BIT DUAL 5V 14-SOIC |
| AD8582AN | IC DAC DUAL 12BIT 5V 24-DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7994BRUZ-1REEL | 功能描述:IC ADC 12BIT 4CHAN I2C 16TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| AD7994-X | 制造商:AD 制造商全称:Analog Devices 功能描述:4-Channel, 10- and 12-Bit ADCs with I2C Compatible Interface in 16-Lead TSSOP |
| AD7995 | 制造商:AD 制造商全称:Analog Devices 功能描述:4-Channel, 12-/10-/8-Bit ADC with I2C-Compatible Interface in 8-Lead SOT-23 |
| AD7995ARJZ-0RL | 功能描述:IC ADC 10BIT 4CHAN I2C SOT23-8 RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 其它有关文件:TSA1204 View All Specifications 标准包装:1 系列:- 位数:12 采样率（每秒）:20M 数据接口:并联 转换器数目:2 功率耗散（最大）:155mW 电压电源:模拟和数字 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-TQFP 供应商设备封装:48-TQFP（7x7） 包装:Digi-Reel® 输入数目和类型:4 个单端，单极；2 个差分，单极 产品目录页面:1156 (CN2011-ZH PDF) 其它名称:497-5435-6 |
| AD7995YRJZ-0 | 制造商:AD 制造商全称:Analog Devices 功能描述:4-Channel, 12-/10-/8-Bit ADC with I2CCompatible Interface in 8-Lead SOT23 |
发布紧急采购，3分钟左右您将得到回复。