- 您现在的位置：买卖IC网 > PDF目录10575 > AD7995ARJZ-0RL (Analog Devices Inc)IC ADC 10BIT 4CHAN I2C SOT23-8 PDF资料下载
参数资料
| 型号： | AD7995ARJZ-0RL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 8/28页 |
| 文件大小： | 0K |
| 描述： | IC ADC 10BIT 4CHAN I2C SOT23-8 |
| 产品变化通告： | AD7991,5,9 Offset Error Change 17/Sept/2010 |
| 设计资源： | Using AD8599 as an Ultralow Distortion Driver for the AD7995 (CN0044) |
| 标准包装： | 1 |
| 位数： | 10 |
| 采样率（每秒）： | 1M |
| 数据接口： | I²C，串行 |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 4.68mW |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-23-8 |
| 供应商设备封装： | SOT-23-8 |
| 包装： | 标准包装 |
| 输入数目和类型： | 4 个单端，单极 |
| 其它名称： | AD7995ARJZ-0RLDKR |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
AD7991/AD7995/AD7999
Rev. B | Page 16 of 28
TERMINOLOGY
Signal-to-Noise and Distortion (SINAD) Ratio
The measured ratio of signal-to-noise and distortion at the output
of the ADC. The signal is the rms amplitude of the fundamental.
Noise is the sum of the nonfundamental signals excluding dc,
up to half the sampling frequency (fS/2). The ratio is dependent
on the number of quantization levels in the digitization process:
the more levels, the smaller the quantization noise. The theoretical
SINAD ratio for an ideal N-bit converter with a sine wave input
is given by
Signal-to-(Noise + Distortion) = (6.02 N + 1.76) dB
Therefore, SINAD is 49.92 dB for an 8-bit converter, 61.96 dB
for a 10-bit converter, and 74 dB for a 12-bit converter.
Total Harmonic Distortion (THD)
The ratio of the rms sum of harmonics to the fundamental. For
the AD7991/AD7995/AD7999, it is defined as
1
6
5
4
3
2
V
THD
2
log
20
)
dB
(
+
=
where:
V1 is the rms amplitude of the fundamental.
V2, V3, V4, V5, and V6 are the rms amplitudes of the second
through sixth harmonics.
Peak Harmonic or Spurious Noise
The ratio of the rms value of the next largest component in the
ADC output spectrum (up to fS/2 and excluding dc) to the rms
value of the fundamental. Typically, the value of this specification
is determined by the largest harmonic in the spectrum, but for
ADCs where the harmonics are buried in the noise floor, the
largest harmonic may be a noise peak.
Intermodulation Distortion
With inputs consisting of sine waves at two frequencies, fa
and fb, any active device with nonlinearities creates distortion
products at sum and difference frequencies of mfa ± nfb, where
m, n = 0, 1, 2, 3, and so on. Intermodulation distortion terms
are those for which neither m nor n equals 0. For example,
second-order terms include (fa + fb) and (fa fb), and
third-order terms include (2fa + fb), (2fa fb), (fa + 2fb), and
(fa 2fb).
The AD7991/AD7995/AD7999 are tested using the CCIF standard,
where two input frequencies near the maximum input bandwidth
are used. In this case, the second-order terms are usually distanced
in frequency from the original sine waves, and the third-order
terms are usually at a frequency close to the input frequencies. As a
result, the second- and third-order terms are specified separately.
The calculation of intermodulation distortion is, like the THD
specification, the ratio of the rms sum of the individual distortion
products to the rms amplitude of the sum of the fundamentals,
expressed in decibels.
Channel-to-Channel Isolation
Channel-to-channel isolation is a measure of the level of
crosstalk between any two channels. It is measured by applying
a full-scale sine wave signal to all unselected input channels and
then determining the degree to which the signal attenuates in
the selected channel with a 10 kHz signal. The frequency of the
signal in each of the unselected channels is increased from 2 kHz
up to 92 kHz. Figure 14 shows the worst-case across all four
channels for the AD7991.
Full-Power Bandwidth
The input frequency at which the amplitude of the reconstructed
fundamental is reduced by 0.1 dB or 3 dB for a full-scale input.
Integral Nonlinearity
The maximum deviation from a straight line passing through
the endpoints of the ADC transfer function. The endpoints are
at zero scale (a point 1 LSB below the first code transition) and
full scale (a point 1 LSB above the last code transition).
Differential Nonlinearity
The difference between the measured and the ideal 1 LSB
change between any two adjacent codes in the ADC.
Offset Error
The deviation of the first code transition (00 … 000 to
00 … 001) from the ideal—that is, AGND + 1 LSB.
Offset Error Match
The difference in offset error between any two channels.
Gain Error
The deviation of the last code transition (111 … 110 to
111 … 111) from the ideal (that is, VREF 1 LSB) after
the offset error has been adjusted out.
Gain Error Match
The difference in gain error between any two channels.
相关PDF资料 |
PDF描述 |
|---|---|
| MAX9539EUI+T | IC ADDER 28-TSSOP |
| VE-B5V-MX-F3 | CONVERTER MOD DC/DC 5.8V 75W |
| VE-JV3-MY-F3 | CONVERTER MOD DC/DC 24V 50W |
| VE-JVR-MY-F1 | CONVERTER MOD DC/DC 7.5V 50W |
| VE-BTF-MX-F1 | CONVERTER MOD DC/DC 72V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7995YRJZ-0 | 制造商:AD 制造商全称:Analog Devices 功能描述:4-Channel, 12-/10-/8-Bit ADC with I2CCompatible Interface in 8-Lead SOT23 |
| AD7995YRJZ-0500RL7 | 功能描述:IC ADC 10BIT 4CH SAR I2C SOT23-8 RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
| AD7995YRJZ-0RL | 功能描述:IC ADC 10BIT 4CH I2C SOT23-8 RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:2,500 系列:- 位数:16 采样率（每秒）:15 数据接口:MICROWIRE?，串行，SPI? 转换器数目:1 功率耗散（最大）:480µW 电压电源:单电源 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:38-WFQFN 裸露焊盘 供应商设备封装:38-QFN（5x7） 包装:带卷 (TR) 输入数目和类型:16 个单端，双极；8 个差分，双极 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| AD7995YRJZ-1 | 制造商:AD 制造商全称:Analog Devices 功能描述:4-Channel, 12-/10-/8-Bit ADC with I2CCompatible Interface in 8-Lead SOT23 |
| AD7995YRJZ-1500RL7 | 功能描述:IC ADC 10BIT 4CH SAR I2C SOT23-8 RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
发布紧急采购，3分钟左右您将得到回复。