参数资料
| 型号： | AD8015AR |
| 厂商： | Analog Devices Inc |
| 文件页数： | 3/8页 |
| 文件大小： | 0K |
| 描述： | IC AMP TRANSIMPEDANCE 8-SOIC |
| 标准包装： | 98 |
| 放大器类型： | 转阻 |
| 电路数： | 1 |
| 输出类型： | 差分 |
| 增益带宽积： | 240MHz |
| 电流 - 电源： | 25mA |
| 电压 - 电源，单路/双路(±)： | 4.5 V ~ 11 V，±2.25 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 管件 |
AD8015
REV. A
–3–
.
V1
+VS
CLOCK
RECOVERY
LPF:
3dB@
0.7 x F
LPF:
3dB@
0.7 x F
QUANTIZER
R > 40
C1 >100pF
4.5V < VS < 11V
CLK
DATA
R
C1
10k
5
6
7
8
4
3
2
1
AD8015
50
+1
G = 3
G = 30
50
+1
– +
+VS
1.7V
+VS
Figure 3. Fiber Optic Receiver Application: Photodiode
Referred to Positive Supply
PHOTODIODE REFERRED TO NEGATIVE SUPPLY
Figure 4 shows the AD8015 used in a circuit where the photo-
diode is referred to the negative supply. This results in a larger
back bias voltage than when referring the photodiode to the
positive supply. The larger back bias voltage on the photodiode
decreases the photodiode’s capacitance thereby increasing its
bandwidth. The R2, C2 network shown in Figure 4 is added to
decouple the photodiode to the positive supply. This improves
PSRR.
+VS
1.7V
+VS
R2
C2
R > 40
C1 >100pF
4.5V < VS < 11V
R2 AND C2 OPTIONAL
FOR IMPROVED PSRR
V1
+VS
CLOCK
RECOVERY
LPF:
3dB@
0.7 x F
LPF:
3dB@
0.7 x F
QUANTIZER
CLK
DATA
R
C1
10k
5
6
7
8
4
3
2
1
AD8015
50
+1
G = 3
G = 30
50
+1
– +
+VS
1.7V
Figure 4. Fiber Optic Receiver Application: Photodiode
Referred to Negative Supply
FIBER OPTIC SYSTEM NOISE PERFORMANCE
The AD8015 maintains 26.5 nA referred to input (RTI) to 100
MHz. Calculations below translate this specification into mini-
mum power level and bit error rate specifications for SONET
and FDDI systems. The dominant sources of noise are: 10 k
feedback resistor current noise, input bipolar transistor base
current noise, and input voltage noise.
The AD8015 has dielectrically isolated devices and bond pads
that minimize stray capacitance at the IIN pin. Input voltage
noise is negligible at lower frequencies, but can become the
dominant noise source at high frequencies due to IIN pin stray
capacitance. Minimizing the stray capacitance at the IIN pin is
critical to maintaining low noise levels at high frequencies. The
pins surrounding the IIN pin (Pins 1 and 3) have no internal
connection and should be left unconnected in an application.
This minimizes IIN pin package capacitance. It is best to have no
ground plane or metal runs near Pins 1, 2, and 3 and to mini-
mize capacitance at the IIN pin.
The AD8015AR (8-pin SOIC) IIN pin total stray capacitance is
0.4 pF without the photodiode. Photodiodes used for SONET
or FDDI systems typically add 0.3 pF, resulting in roughly
0.7 pF total stray capacitance.
PIN CONFIGURATION
10k
5
6
7
8
4
3
2
1
AD8015
50
+1
NC
IIN
NC
VBYP
–VS
–OUTPUT
+OUTPUT
+VS
G = 3
G = 30
NC = NO CONNECT
50
+1
– +
+VS
1.7V
METALIZATION PHOTOGRAPH
Dimensions shown in microns. Not to scale.
FIBER OPTIC RECEIVER APPLICATIONS
In a fiber optic receiver, the photodiode can be placed from the
IIN pin to either the positive or negative supply. The AD8015
converts the current from the photodiode to a differential volt-
age in these applications. The voltage at the VBYP pin is ≈1.8 V
below the positive supply. This node must be bypassed with a
capacitor (C1 in Figures 3 and 4 below) to the signal ground. If
large levels of power supply noise exist, then connecting C1 to
+VS is recommended for improved noise immunity. For opti-
mum performance, choose C1 such that C1 > 1/(2
π × 1000 ×
fMIN); where fMIN is the minimum useful
frequency in Hz.
PHOTODIODE REFERRED TO POSITIVE SUPPLY
Figure 3 shows the AD8015 used in a circuit where the photo-
diode is referred to the positive supply. The back bias voltage on
the photodiode is
≈1.8 V. This method of referring the photo-
diode provides greater power supply noise immunity (PSRR)
than referring the photodiode to the negative supply. The signal
path is referred to the positive rail, and the photodiode capaci-
tance is not modulated by high frequency noise that may exist
on the negative rail.
OPTIONAL
+VS CONNECTION
+OUTPUT
–OUTPUT
IIN
VBYP
973
998
+VS
838
–VS
813
NOTE:
FOR BEST PERFORMANCE ATTACH PACKAGE
SUBSTRATE TO +VS.
MATERIAL AT BACK OF DIE IS SILICON. USE OF
+VS OR –VS FOR DIE ATTACH IS ACCEPTABLE.
相关PDF资料 |
PDF描述 |
|---|---|
| AD8017ARZ-REEL | IC AMP GP DUAL LP LDIST 8SOIC |
| AD8021AR | IC OPAMP VF LN LP LDIST 8SOIC |
| AD8022ARZ-REEL7 | IC OPAMP VF DUAL LN LP 8SOIC |
| AD8024ARZ-REEL7 | IC OPAMP CF QUAD LP 50MA 16SOIC |
| AD8028ARMZ-REEL7 | IC OPAMP R-R DUAL LDIST 10MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD8015AR-REEL | 制造商:Analog Devices 功能描述:SP Amp Transimpedance Amp Single ±5.5V/11V 8-Pin SOIC N T/R 制造商:Analog Devices 功能描述:SP AMP TRANSIMPEDANCE AMP SGL 5.5V/11V 8SOIC N - Tape and Reel 制造商:Rochester Electronics LLC 功能描述:DIFF-OUT X-IMPEDANCE AMP - Tape and Reel |
| AD8015AR-REEL7 | 制造商:Analog Devices 功能描述:SP AMP TRANSIMPEDANCE AMP SGL 5.5V/11V 8SOIC N - Tape and Reel |
| AD8015ARZ | 功能描述:IC AMP TRANSIMPEDANCE 8-SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:2,500 系列:- 放大器类型:通用 电路数:4 输出类型:- 转换速率:0.6 V/µs 增益带宽积:1MHz -3db带宽:- 电流 - 输入偏压:45nA 电压 - 输入偏移:2000µV 电流 - 电源:1.4mA 电流 - 输出 / 通道:40mA 电压 - 电源，单路/双路(±):3 V ~ 32 V，±1.5 V ~ 16 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:14-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:14-TSSOP 包装:带卷 (TR) 其它名称:LM324ADTBR2G-NDLM324ADTBR2GOSTR |
| AD8015ARZ | 制造商:Analog Devices 功能描述:IC TRANSIMPEDANCE AMP 240MHZ SOIC-8 |
| AD8015ARZ-REEL | 制造商:Analog Devices 功能描述:SP Amp Transimpedance Amp Single ±5.5V/11V 8-Pin SOIC N T/R |
发布紧急采购，3分钟左右您将得到回复。