- 您现在的位置：买卖IC网 > PDF目录16531 > AD8016ARE-EVAL (Analog Devices Inc)BOARD EVAL FOR AD8016ARE PDF资料下载
参数资料
| 型号： | AD8016ARE-EVAL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 8/21页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR AD8016ARE |
| 应用说明： | Using the Active Filter Design Tool, AN-649 |
| 标准包装： | 1 |
| 主要目的： | 接口，线路驱动器，xDSL |
| 已用 IC / 零件： | AD8016ARE |
| 已供物品： | 板 |
Data Sheet
AD8016
Rev. C | Page 15 of 20
The bias level can be controlled with TTL logic levels (high = 1)
applied to the PWDN1 and PWDN0 pins alone or in combina-
tion with the BIAS control pin. The DGND or digital ground
pin is the logic ground reference for the PWDN1 and PWDN0
pins. In typical ADSL applications where ±12 V or ±6 V
supplies (also single supplies) are used, the DGND pin is
connected to analog ground.
The BIAS control pin by itself is a means to continuously adjust
pulling out a current of 0 μA (or open) to approximately200 μA,
the quiescent current can be adjusted from 100% (full on) to a
full off condition. The full off condition yields a high output
impedance. Because of an on-chip resistor variation of up to
±20%, the actual amount of current required to fully shut down
the AD8016 can vary. To institute a full chip shutdown, a pull-
down current of 250 μA is recommended. See Figure 43 for the
logic drive circuit for complete amplifier shutdown. Figure 37
and Figure 38 show the relationship between current pulled out
of the BIAS pin (IBIAS) and the supply current (IQ). A typical
shutdown IQ is less than 1 mA total. Alternatively, an external
pull-down resistor to ground or a current sink attached to the
The BIAS pin may be used in combination with the PWDN1
and PWDN0 pins; however, diminished MTPR performance
may result when IQ is lowered too much. Current pulled away
from the BIAS pin shunts away a portion of the internal bias
current. Setting PWDN1 or PWDN0 to Logic 0 also shunts
away a portion of the internal bias current. The reduction of
quiescent bias levels due to the use of PWDN1 and PWDN0 is
consistent with the percentages established in Table 7. When
PWDN0 alone is set to Logic 0, and no other means of reducing
the internal bias currents is used, full-rate ADSL signals may be
driven while maintaining reasonable levels of MTPR.
Figure 43. Logic Drive of BIAS Pin for Complete Amplifier Shutdown
THERMAL SHUTDOWN
The AD8016 ARB is designed to incorporate shutdown
protection against accidental thermal overload. In the event
of thermal overload, the AD8016 was designed to shut down
at a junction temperature of 165°C and return to normal
operation at a junction temperature 140°C. The AD8016
continues to operate, cycling on and off, as long as the thermal
overload condition remains. The frequency of the protection
cycle depends on the ambient environment, severity of the
thermal overload condition, the power being dissipated, and
the thermal mass of the PCB beneath the AD8016. When the
AD8016 begins to cycle due to thermal stress, the internal
shutdown circuitry draws current out of the node connected
in common with the BIAS pin, while the voltage at the BIAS
pin goes to the negative rail. When the junction temperature
returns to 140°C, current is no longer drawn from this node,
and the BIAS pin voltage returns to the positive rail. Under
these circumstances, the BIAS pin can be used to trip an alarm
indicating the presence of a thermal overload condition.
Figure 44 also shows three circuits for converting this signal to
a standard logic level.
Figure 44. Shutdown and Alarm Circuit
R2
50k
BIAS
R1*
3.3V LOGIC
2N3904
*R1 = 47k FOR ±12VS OR +12VS,
R1 = 22k FOR ±6VS.
01019-
043
5V
BIAS
ALARM
1/4 HCF 40109B
SGS–THOMSON
5V
1M
BIAS
ALARM
MIN β 350
OR
VEE
10k
100k
200A
0A – 200A
VCC
BIAS
PWDN1
BIAS
OR
V = VCC –0.2V
SHUT-
DOWN
AD8016
PWDN0
01
9-
044
相关PDF资料 |
PDF描述 |
|---|---|
| UPJ0J681MPD1TD | CAP ALUM 680UF 6.3V 20% RADIAL |
| 6374109-9 | C/A 62.5/125 1.6MM LC 1.63M |
| MCP102T-315E/TT | IC SUPERVISOR 3.08V LOW SOT-23B |
| RCC20DCAI-S189 | CONN EDGECARD 40POS R/A .100 SLD |
| AD8016ARB-EVAL | BOARD EVAL FOR AD8016ARB |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD8016ARE-REEL | 制造商:Analog Devices 功能描述:ADSL Driver Dual 28-Pin TSSOP EP T/R 制造商:Rochester Electronics LLC 功能描述:TSSOP LOW POWER, HIGH OUTPUT CURRENT AMP - Tape and Reel |
| AD8016ARE-REEL7 | 制造商:Analog Devices 功能描述:ADSL Driver Dual 28-Pin TSSOP EP T/R |
| AD8016AREZ | 功能描述:IC AMP XDSL LINE DVR 28-TSSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:1 系列:- 类型:线路收发器 驱动器/接收器数:5/3 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC 包装:Digi-Reel® 产品目录页面:918 (CN2011-ZH PDF) 其它名称:296-25096-6 |
| AD8016AREZ-REEL | 功能描述:IC LINE DRIVER ADSL 28TSSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:27 系列:- 类型:收发器 驱动器/接收器数:3/3 规程:RS232，RS485 电源电压:4.75 V ~ 5.25 V 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC 包装:管件 |
| AD8016AREZ-REEL7 | 功能描述:IC LINE DRIVER ADSL 28TSSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:27 系列:- 类型:收发器 驱动器/接收器数:3/3 规程:RS232，RS485 电源电压:4.75 V ~ 5.25 V 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。