- 您现在的位置：买卖IC网 > PDF目录8530 > AD8023ARZ-REEL (Analog Devices Inc)IC AMP VIDEO TRIPLE HC 14-SOIC PDF资料下载
参数资料
| 型号： | AD8023ARZ-REEL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 2/11页 |
| 文件大小： | 0K |
| 描述： | IC AMP VIDEO TRIPLE HC 14-SOIC |
| 标准包装： | 2,500 |
| 应用： | 电流反馈 |
| 电路数： | 3 |
| -3db带宽： | 125MHz |
| 转换速率： | 1200 V/µs |
| 电流 - 电源： | 7mA |
| 电流 - 输出 / 通道： | 70mA |
| 电压 - 电源，单路/双路(±)： | 4.2 V ~ 15 V，±2.1 V ~ 7.5 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 14-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 14-SOICN |
| 包装： | 带卷 (TR) |
AD8023
REV. A
–10–
Figure 33. 50% Overload Recovery, Gain = +10,
(RF = 300
, RL = 1 k, VS = ±7.5 V)
As noted in the warning under Maximum Power Dissipation, a
high level of input overdrive in a high noninverting gain circuit
can result in a large current flow in the input stage. Though this
current is internally limited to about 30 mA, its effect on the
total power dissipation may be significant.
Disable Mode Operation
Pulling the voltage on any one of the Disable pins about 1.6 V up
from the negative supply will put the corresponding amplifier
into a disabled, powered down, state. In this condition, the
amplifier’s quiescent current drops to about 1.3 mA, its output
becomes a high impedance, and there is a high level of isolation
from input to output. In the case of a gain of two line driver for
example, the impedance at the output node will be about the
same as for a 1.5 k
resistor (the feedback plus gain resistors)
in parallel with a 12 pF capacitor.
Leaving the Disable pin disconnected (floating) will leave the
corresponding amplifier operational, in the enabled state. The
input impedance of the disable pin is about 25 k
in parallel
with a few picofarads. When driven to 0 V, with the negative
supply at –7.5 V, about 100
A flows into the disable pin.
When the disable pins are driven by complementary output
CMOS logic, on a single 5 V supply, the disable and enable
times are about 50 ns. When operated on dual supplies, level
shifting will be required from standard logic outputs to the
Disable pins. Figure 33 shows one possible method, which
results in a negligible increase in switching time.
+7.5V
10k
TO DISABLE PIN
VI
VI HIGH => AMPLIFIER ENABLED
VI LOW => AMPLIFIER DISABLED
–7.5V
4k
15k
+5
Figure 34. Level Shifting to Drive Disable Pins on Dual
Supplies
The AD8023’s input stages include protection from the large
differential input voltages that may be applied when disabled.
Internal clamps limit this voltage to about
±3 V. The high input to
output isolation will be maintained for voltages below this limit.
Figure 31. Circuit for Driving a Capacitive Load
Table II. Recommended Feedback and Series Resistors vs.
Capacitive Load and Gain
RS – Ohms
CL – pF
RF – Ohms
G = 2
G
≥ 3
20
2k
0
50
2k
10
100
2k
15
200
3k
10
300
3k
10
≥500
3k
10
Figure 32. Pulse Response Driving a Large Load Capacitor.
CL = 300 pF, G = +3, RF = 750
, RS = 16.9 , RL = 10 k
Overload Recovery
The three important overload conditions are: input common-
mode voltage overdrive, output voltage overdrive, and input
current overdrive. When configured for a low closed-loop gain,
this amplifier will quickly recover from an input common-mode
voltage overdrive; typically in under 25 ns. When configured for
a higher gain, and overloaded at the output, the recovery time
will also be short. For example, in a gain of +10, with 50%
overdrive, the recovery time of the AD8023 is about 20 ns (see
Figure 31). For higher overdrive, the response is somewhat
slower. For 100% overdrive, (in a gain of +10), the recovery
time is about 80 ns.
V
IN
V
O
V
IN
V
O
4
+VS
AD8023
1.0 F
0.1 F
11
1.0 F
0.1 F
–VS
RG
RT
VIN
15
CL
VO
RF
RS
相关PDF资料 |
PDF描述 |
|---|---|
| VI-J4D-MZ-B1 | CONVERTER MOD DC/DC 85V 25W |
| AD830AR | IC VIDEO DIFF AMP HS 8-SOIC |
| VI-J4B-MZ-B1 | CONVERTER MOD DC/DC 95V 25W |
| 6-1877846-6 | PLUG 6POS 80 DEG BLK/BLU 2.7-3.9 |
| AD811AN | IC CURR-FDBK AMP VIDEO HS 8-DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD8023ARZ-REEL7 | 功能描述:IC AMP VIDEO TRIPLE HC 14-SOIC RoHS:是 类别:集成电路 (IC) >> 线性 - 放大器 - 视频放大器和频缓冲器 系列:- 标准包装:1,000 系列:- 应用:驱动器 输出类型:差分 电路数:3 -3db带宽:350MHz 转换速率:1000 V/µs 电流 - 电源:14.5mA 电流 - 输出 / 通道:60mA 电压 - 电源，单路/双路(±):5 V ~ 12 V，±2.5 V ~ 6 V 安装类型:表面贴装 封装/外壳:20-VFQFN 裸露焊盘 供应商设备封装:20-QFN 裸露焊盘（4x4） 包装:带卷 (TR) |
| AD8024 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Quad 350 MHz 24 V Amplifier |
| AD8024_01 | 制造商:AD 制造商全称:Analog Devices 功能描述:Quad 350 MHz 24 V Amplifier |
| AD80241BBCZ | 制造商:Analog Devices 功能描述: |
| AD80241BBCZRL | 制造商:Analog Devices 功能描述: |
发布紧急采购，3分钟左右您将得到回复。