参数资料
| 型号： | AD8030ARZ-REEL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 24/25页 |
| 文件大小： | 0K |
| 描述： | IC AMP GP R-R DUAL LP 8SOIC |
| 标准包装： | 2,500 |
| 放大器类型： | 通用 |
| 电路数： | 2 |
| 输出类型： | 满摆幅 |
| 转换速率： | 63 V/µs |
| -3db带宽： | 125MHz |
| 电流 - 输入偏压： | 1.7µA |
| 电压 - 输入偏移： | 2000µV |
| 电流 - 电源： | 1.4mA |
| 电流 - 输出 / 通道： | 170mA |
| 电压 - 电源，单路/双路(±)： | 2.7 V ~ 12 V，±1.35 V ~ 6 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SO |
| 包装： | 带卷 (TR) |
Data Sheet
AD8029/AD8030/AD8040
Rev. B | Page 7 of 24
ABSOLUTE MAXIMUM RATINGS
Table 4. AD8029/AD8030/AD8040 Stress Ratings
Parameter
Rating
Supply Voltage
12.6 V
Power Dissipation
Common-Mode Input Voltage
±VS ± 0.5 V
Differential Input Voltage
±1.8 V
Storage Temperature
–65°C to +125°C
Operating Temperature Range
–40°C to +125°C
Lead Temperature Range
(Soldering 10 sec)
300°C
Junction Temperature
150°C
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
MAXIMUM POWER DISSIPATION
The maximum safe power dissipation in the AD8029/AD8030/
AD8040 package is limited by the associated rise in junction
temperature (TJ) on the die. The plastic encapsulating the die
locally reaches the junction temperature. At approximately
150°C, which is the glass transition temperature, the plastic
changes its properties. Even temporarily exceeding this
temperature limit may change the stresses that the package
exerts on the die, permanently shifting the parametric
performance of the AD8029/AD8030/AD8040. Exceeding a
junction temperature of 175°C for an extended period can
result in changes in silicon devices, potentially causing failure.
The still-air thermal properties of the package and PCB (θJA),
ambient temperature (TA), and the total power dissipated in the
package (PD) determine the junction temperature of the die.
The junction temperature can be calculated as
TJ = TA + (PD × θJA)
The power dissipated in the package (PD) is the sum of the
quiescent power dissipation and the power dissipated in the
package due to the load drive for all outputs. The quiescent
power is the voltage between the supply pins (VS) times the
quiescent current (IS). Assuming the load (RL) is referenced to
midsupply, the total drive power is VS/2 × IOUT, some of which is
dissipated in the package and some in the load (VOUT × IOUT).
The difference between the total drive power and the load
power is the drive power dissipated in the package.
PD = Quiescent Power + (Total Drive Power – Load Power)
(
)
L
OUT
L
OUT
S
D
R
V
R
V
I
V
P
2
–
2
×
+
×
=
RMS output voltages should be considered. If RL is referenced to
VS–, as in single-supply operation, then the total drive power is
VS × IOUT.
If the rms signal levels are indeterminate, consider the worst
case, when VOUT = VS/4 for RL to midsupply:
(
) (
)
L
S
D
R
V
I
V
P
2
4
/
+
×
=
In single-supply operation with RL referenced to VS–, worst case
is VOUT = VS/2.
Airflow increases heat dissipation, effectively reducing θJA. Also,
more metal directly in contact with the package leads from
metal traces, through holes, ground, and power planes reduce
the θJA. Care must be taken to minimize parasitic capacitances
at the input leads of high speed op amps, as discussed in the
PCB Layout section.
Figure 6 shows the maximum safe power dissipation in the
package versus the ambient temperature for the SOIC-8
(125°C/W), SOT23-8 (160°C/W), SOIC-14 (90°C/W),
TSSOP-14 (120°C/W), and SC70-6 (208°C/W) packages on a
JEDEC standard 4-layer board. θJA values are approximations.
–40
–20 –10
–30
0
10 20 30 40 50 60 70 80 90 100 110 120
2.5
MAXIMUM
POWER
DISSIPATION
(W)
1.0
0.5
1.5
2.0
0
AMBIENT TEMPERATURE (°C)
SOIC-8
TSSOP-14
SOIC-14
SOT-23-8
SC70-6
03679-A-018
Figure 6. Maximum Power Dissipation
Output Short Circuit
Shorting the output to ground or drawing excessive current
from the AD8029/AD8030/AD8040 could cause catastrophic
failure.
ESD CAUTION
相关PDF资料 |
PDF描述 |
|---|---|
| AD8039ARZ-REEL | IC OPAMP VF DUAL LP LN 8SOIC |
| AD8614ART-REEL7 | IC OPAMP GP R-R 5.5MHZ SOT23-5 |
| LT6211IMS#TRPBF | IC AMP CURR FDBK DUAL R-R 10MSOP |
| OP27GSZ-REEL | IC OPAMP GP 8MHZ LN PREC 8SOIC |
| LT1782CS6#TRM | IC OPAMP R-R I/O MICRPWR SOT23-6 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD8030ARZ-REEL7 | 功能描述:IC AMP GP R-R DUAL LP 8SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:1,000 系列:- 放大器类型:电压反馈 电路数:4 输出类型:满摆幅 转换速率:33 V/µs 增益带宽积:20MHz -3db带宽:30MHz 电流 - 输入偏压:2nA 电压 - 输入偏移:3000µV 电流 - 电源:2.5mA 电流 - 输出 / 通道:30mA 电压 - 电源，单路/双路(±):4.5 V ~ 16.5 V，±2.25 V ~ 8.25 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SOIC 包装:带卷 (TR) |
| AD8031 | 制造商:AD 制造商全称:Analog Devices 功能描述:2.7 V, 800 レA, 80 MHz Rail-to-Rail I/O Amplifiers |
| AD8031_06 | 制造商:AD 制造商全称:Analog Devices 功能描述:2.7 V, 800 レA, 80 MHz Rail-to-Rail I/O Amplifiers |
| AD8031A | 制造商:AD 制造商全称:Analog Devices 功能描述:2.7 V, 800 uA, 80 MHz Rail-to-Rail I/O Amplifiers |
| AD8031AN | 制造商:Rochester Electronics LLC 功能描述:PDIP SINGLE LOW POWER OP AMP - Bulk 制造商:Analog Devices 功能描述:IC SM AMP LOW POWER RRI/O |
发布紧急采购，3分钟左右您将得到回复。