- 您现在的位置：买卖IC网 > PDF目录16924 > AD8037-EB (Analog Devices Inc)BOARD EVAL FOR AD8037 PDF资料下载
参数资料
| 型号： | AD8037-EB |
| 厂商： | Analog Devices Inc |
| 文件页数： | 8/24页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR AD8037 |
| 应用说明： | Using the Active Filter Design Tool, AN-649 |
| 标准包装： | 1 |
| 每 IC 通道数： | 1 - 单 |
| 放大器类型： | 电压反馈 |
| 输出类型： | 单端 |
| 板类型： | 裸（未填充） |
| 已供物品： | 板 |
| 已用 IC / 零件： | 8-SOIC 封装 |
| 相关产品： | AD8037ANZ-ND - IC OPAMP VF ULDIST LN 70MA 8DIP AD8037ARZ-REEL7-ND - IC OPAMP VF ULDIST LN 70MA 8SOIC AD8037ARZ-REEL-ND - IC OPAMP VF ULDIST LN 70MA 8SOIC AD8037ARZ-ND - IC OPAMP VF ULDIST LN 70MA 8SOIC AD8037AR-ND - IC OPAMP VF ULDIST LN 70MA 8SOIC |
AD8036/AD8037
REV. B
–15–
THEORY OF OPERATION
General
The AD8036 and AD8037 are wide bandwidth, voltage feedback
clamp amplifiers. Since their open-loop frequency response fol-
lows the conventional 6 dB/octave roll-off, their gain bandwidth
product is basically constant. Increasing their closed-loop gain
results in a corresponding decrease in small signal bandwidth. This
can be observed by noting the bandwidth specification, between
the AD8036 (gain of 1) and AD8037 (gain of 2). The AD8036/
AD8037 typically maintain 65 degrees of phase margin. This
high margin minimizes the effects of signal and noise peaking.
While the AD8036 and AD8037 can be used in either an invert-
ing or noninverting configuration, the clamp function will only
work in the noninverting mode. As such, this section shows con-
nections only in the noninverting configuration. Applications
that require an inverting configuration will be discussed in the
Applications section. In applications that do not require clamp-
ing, Pins 5 and 8 (respectively VL and VH) may be left floating.
See Input Clamp Amp Operation and Applications sections
otherwise.
Feedback Resistor Choice
The value of the feedback resistor is critical for optimum perfor-
mance on the AD8036 (gain +1) and less critical as the gain
increases. Therefore, this section is specifically targeted at
the AD8036.
At minimum stable gain (+1), the AD8036 provides optimum
dynamic performance with RF = 140
. This resistor acts only
as a parasitic suppressor against damped RF oscillations that
can occur due to lead (input, feedback) inductance and parasitic
capacitance. This value of RF provides the best combination of
wide bandwidth, low parasitic peaking, and fast settling time.
In fact, for the same reasons, a 100–130
resistor should be
placed in series with the positive input for other AD8036 non-
inverting configurations. The correct connection is shown in
Figure 3.
RF
100 - 130
RTERM
RF
RG
G = 1+
RG
VH
VL
+VS
–VS
VIN
VOUT
0.1 F
10 F
0.1 F
10 F
AD8036/
AD8037
Figure 3. Noninverting Operation
For general voltage gain applications, the amplifier bandwidth
can be closely estimated as:
f
3 dB
ω
O
2
π 1+
R
F
R
G
This estimation loses accuracy for gains of +2/–1 or lower due
to the amplifier’s damping factor. For these “low gain” cases,
the bandwidth will actually extend beyond the calculated value
(see Closed-Loop BW plots, TPCs 13 and 25).
Pulse Response
Unlike a traditional voltage feedback amplifier, where the slew
speed is dictated by its front end dc quiescent current and gain
bandwidth product, the AD8036 and AD8037 provide “on
demand” current that increases proportionally to the input
“step” signal amplitude. This results in slew rates (1200 V/
s)
comparable to wideband current feedback designs. This, com-
bined with relatively low input noise current (2.1 pA/
√Hz), gives
the AD8036 and AD8037 the best attributes of both voltage and
current feedback amplifiers.
Large Signal Performance
The outstanding large signal operation of the AD8036 and
AD8037 is due to a unique, proprietary design architecture.
In order to maintain this level of performance, the maximum
350 V-MHz product must be observed, (e.g., @ 100 MHz,
VO
≤ 3.5 V p-p).
Power Supply and Input Clamp Bypassing
Adequate power supply bypassing can be critical when optimiz-
ing the performance of a high frequency circuit. Inductance in
the power supply leads can form resonant circuits that produce
peaking in the amplifier’s response. In addition, if large current
transients must be delivered to the load, then bypass capacitors
(typically greater than 1
F) will be required to provide the best
settling time and lowest distortion. A parallel combination of at
least 4.7
F, and between 0.1 F and 0.01 F, is recommended.
Some brands of electrolytic capacitors will require a small series
damping resistor
≈4.7 for optimum results.
When the AD8036 and AD8037 are used in clamping mode,
and a dc voltage is connected to clamp inputs VH and VL, a 0.1
F
bypassing capacitor is required between each input pin and
ground in order to maintain stability.
Driving Capacitive Loads
The AD8036 and AD8037 were designed primarily to drive
nonreactive loads. If driving loads with a capacitive compo-
nent is desired, the best frequency response is obtained by
the addition of a small series resistance as shown in Figure 4.
The accompanying graph shows the optimum value for RSERIES
vs. capacitive load. It is worth noting that the frequency response
of the circuit when driving large capacitive loads will be domi-
nated by the passive roll-off of RSERIES and CL. For capacitive
loads of 6 pF or less, no RSERIES is necessary.
RL
1k
RF
RIN
RSERIES
CL
AD8036/
AD8037
RIN
Figure 4. Driving Capacitive Loads
相关PDF资料 |
PDF描述 |
|---|---|
| 1-555858-9 | CABLE ASSY PWR ENTRY 5 WIRE 88" |
| EBM15DCAT | CONN EDGECARD 30POS R/A .156 SLD |
| 823811-000 | BOOT MOLDED |
| MIC2566-1YM TR | IC PCMCIA/CARDBUS SGL 14-SOP |
| AD8036-EB | BOARD EVAL FOR AD8036 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD8037SRZ-EP | 功能描述:IC OPAMP VF LP LN LDIST 8SOIC 制造商:analog devices inc. 系列:- 包装:管件 零件状态:在售 放大器类型:电压反馈 电路数:1 输出类型:- 压摆率:1500 V/μs -3db 带宽:270MHz 电流 - 输入偏置:3μA 电压 - 输入失调:2mV 电流 - 电源:18.5mA 电流 - 输出/通道:70mA 电压 - 电源，单/双（±）:±3 V ~ 6 V 工作温度:-55°C ~ 105°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商器件封装:8-SOIC 标准包装:1 |
| AD8037SRZ-EP-R7 | 功能描述:Voltage Feedback Amplifier 1 Circuit 8-SOIC 制造商:analog devices inc. 系列:- 包装:带卷（TR） 零件状态:有效 放大器类型:电压反馈 电路数:1 输出类型:- 压摆率:1500 V/μs 增益带宽积:- -3db 带宽:270MHz 电流 - 输入偏置:3μA 电压 - 输入失调:2mV 电流 - 电源:18.5mA 电流 - 输出/通道:70mA 电压 - 电源，单/双（±）:±3 V ~ 6 V 工作温度:-55°C ~ 105°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商器件封装:8-SOIC 标准包装:1,000 |
| AD8038 | 制造商:AD 制造商全称:Analog Devices 功能描述:Dual 8-,10-,12-Bit High Bandwidth Multiplying DACs with Serial Interface |
| AD8038_04 | 制造商:AD 制造商全称:Analog Devices 功能描述:Low Power 350 MHz Voltage Feedback Amplifiers |
| AD8038AKS-EBZ | 功能描述:BOARD EVAL FOR AD8038AKS RoHS:是 类别:编程器，开发系统 >> 评估板 - 运算放大器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- |
发布紧急采购，3分钟左右您将得到回复。