- 您现在的位置：买卖IC网 > PDF目录373932 > AD8054AR-REEL (ANALOG DEVICES INC) Metal Oxide Varistor (MOV); Voltage Rating AC, Vrms:1100Vrms; Voltage Rating DC, Vdc:1465VDC; Peak Surge Current (8/20uS), Itm:6500A; Clamping Voltage 8/20us Max :2970V; Capacitance, Cd:170pF; Package/Case:20mm Disc PDF资料下载
参数资料
| 型号： | AD8054AR-REEL |
| 厂商： | ANALOG DEVICES INC |
| 元件分类： | 运动控制电子 |
| 英文描述： | Metal Oxide Varistor (MOV); Voltage Rating AC, Vrms:1100Vrms; Voltage Rating DC, Vdc:1465VDC; Peak Surge Current (8/20uS), Itm:6500A; Clamping Voltage 8/20us Max :2970V; Capacitance, Cd:170pF; Package/Case:20mm Disc |
| 中文描述： | QUAD OP-AMP, 32000 uV OFFSET-MAX, PDSO14 |
| 封装： | MS-012AB, SOIC-14 |
| 文件页数： | 15/16页 |
| 文件大小： | 267K |
| 代理商： | AD8054AR-REEL |
–15–
AD8051/AD8052/AD8054
REV. B
Sync Stripper
Synchronizing pulses are sometimes carried on video signals so
as not to require a separate channel to carry the synchronizing
information. However, for some functions, like A/D conversion,
it is not desirable to have the sync pulses on the video signal.
These pulses will reduce the dynamic range of the video signal
and do not provide any useful information for such a function.
A sync stripper will remove the synchronizing pulses from a
video signal while passing all the useful video information. Fig-
ure 47 shows a practical single supply circuit that uses only a
single AD8051. It is capable of directly driving a reverse termi-
nated video line.
AD8051
0.1
m
F
10
m
F
+
R1
1k
V
R2
1k
V
100
V
TO A/D
+0.8V
(OR 2
3
V
BLANK
)
V
IN
+3V OR +5V
V
BLANK
GROUND
+0.4V
VIDEO WITH SYNC
GROUND
VIDEO WITHOUT SYNC
Figure 47. Sync Stripper
The video signal plus sync is applied to the noninverting input
with the proper termination. The amplifier gain is set equal to
two via the two 1 k
resistors in the feedback circuit. A bias
voltage must be applied to R1 in order that the input signal has
the sync pulses stripped at the proper level.
The blanking level of the input video pulse is the desired place
to remove the sync information. This level is multiplied by two
by the amplifier. This level must be at ground at the output in
order for the sync stripping action to take place. Since the gain
of the amplifier from the input of R1 to the output is –1, a volt-
age equal to 2
×
V
BLANK
must be applied to make the blanking
level come out at ground.
Single Supply Composite Video Line Driver
Many composite video signals have their blanking level at
ground and have video information that is both positive and
negative. Such signals require dual supply amplifiers to pass
them. However, by ac level shifting a single supply amplifier can
be used to pass these signals. The following complications may
arise from such techniques.
Signals of bounded peak-to-peak amplitude that vary in duty
cycle require larger dynamic swing capacity than their (bounded)
peak to peak amplitude after they are ac coupled. As a worst
case, the dynamic signal swing will approach twice the peak-
to-peak value. The two conditions that define the maximum
dynamic wing requirements are a signal that is mostly low, but
goes high with a duty cycle that is a small fraction of a percent.
The opposite condition defines the other extreme.
The worst case of composite video is not quite this demanding.
One bounding condition is a signal that is mostly black for an
entire frame, but has a white (full amplitude) minimum width
spike at least once in a frame.
The other extreme is for a full white video signal. The blanking
intervals and sync tips of such a signal will have negative-going
excursions is compliance with the composite video specifica-
tions. The combination of horizontal and vertical blanking inter-
vals limit such a signal to being at the highest (white) level for a
maximum of about 75% of the time.
As a result of the duty cycles between the two extremes pre-
sented above, a 1 V p-p composite video signal that is multiplied
by a gain of two requires about 3.2 V p-p of dynamic voltage
swing at the output for an op amp to pass a composite video
signal of arbitrary varying duty cycle without distortion.
Some circuits use a sync tip clamp to hold the sync tips at a
relatively constant level in order to lower the amount of dynamic
signal swing required. However, these circuits can have artifacts
like sync tip compression unless they are driven by a source with
a very low output impedance. The AD8051/AD8052/AD8054
have adequate signal swing when running on a single +5 V
supply to handle an ac coupled composite video signal.
The input to the circuit in Figure 48 is a standard composite
(1 V p-p) video signal that has the blanking level at ground. The
input network level shifts the video signal by means of ac cou-
pling. The noninverting input of the op amp is biased to half of
the supply voltage.
The feedback circuit provides unity gain for the dc biasing of the
input, and provides a gain of two for any signals that are in the
video bandwidth. The output is ac coupled and terminated to
drive the line.
The capacitor values were selected for providing minimum “tilt”
or field time distortion of the video signal. These values would
be required for video that is considered to be studio or broad-
cast quality. However, if a lower consumer grade of video,
sometimes referred to as “consumer video” is all that is desired,
the values and the cost of the capacitors can be reduced by as
much as a factor of five with minimum visible degradation in the
picture.
AD8051
R
G
1k
V
R
F
1k
V
+5V
IN
+10
m
F
4.99k
V
220
m
F
1+
m
F
0.1
m
F
R
BT
75
V
10
m
F
+
47
m
F
4.99k
V
R
T
75
V
R
L
75
V
V
OUT
COVIDEO
0.1
m
F
10
m
F
+
Figure 48. Single Supply Composite Video Line Driver
相关PDF资料 |
PDF描述 |
|---|---|
| AD8054AR-REEL7 | VARISTOR 140V RMS 20MM RADIAL |
| AD8054 | Low Cost, High Speed Rail-to-Rail Amplifiers(低成本,高速满幅度四放大器) |
| AD8055AR-REEL | Low Cost, 300 MHz Voltage Feedback Amplifiers |
| AD8055AR-REEL7 | Low Cost, 300 MHz Voltage Feedback Amplifiers |
| AD8055AN | 16-Bit 250 kSPS ADC Par. Out, 4 true bipolar chanels 48-TQFP -40 to 85 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD8054AR-REEL7 | 功能描述:IC OPAMP VF R-R QUAD LP 14SOIC RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:- 放大器类型:J-FET 电路数:2 输出类型:- 转换速率:3.5 V/µs 增益带宽积:1MHz -3db带宽:- 电流 - 输入偏压:30pA 电压 - 输入偏移:2000µV 电流 - 电源:200µA 电流 - 输出 / 通道:- 电压 - 电源，单路/双路(±):7 V ~ 36 V，±3.5 V ~ 18 V 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:8-DIP（0.300"，7.62mm） 供应商设备封装:8-PDIP 包装:管件 |
| AD8054ARU | 功能描述:IC OPAMP VF R-R QUAD LP 14TSSOP RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:150 系列:- 放大器类型:音频 电路数:2 输出类型:- 转换速率:5 V/µs 增益带宽积:12MHz -3db带宽:- 电流 - 输入偏压:100nA 电压 - 输入偏移:500µV 电流 - 电源:6mA 电流 - 输出 / 通道:50mA 电压 - 电源，单路/双路(±):4 V ~ 32 V，±2 V ~ 16 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
| AD8054ARU-EBZ | 功能描述:BOARD EVAL FOR AD8054ARU RoHS:是 类别:编程器，开发系统 >> 评估板 - 运算放大器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- |
| AD8054ARUR | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC |
| AD8054ARU-REEL | 制造商:Analog Devices 功能描述:OP Amp Quad Volt Fdbk R-R O/P 制造商:Analog Devices 功能描述:OP Amp Quad Volt Fdbk R-R O/P ±6V/12V 14-Pin TSSOP T/R |
发布紧急采购，3分钟左右您将得到回复。