- 您现在的位置：买卖IC网 > PDF目录6113 > AD8055ARTZ-REEL7 (Analog Devices Inc)IC OPAMP VF LDIST LN LP SOT23-5 PDF资料下载
参数资料
| 型号： | AD8055ARTZ-REEL7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 5/17页 |
| 文件大小： | 0K |
| 描述： | IC OPAMP VF LDIST LN LP SOT23-5 |
| 标准包装： | 1 |
| 放大器类型： | 电压反馈 |
| 电路数： | 1 |
| 转换速率： | 1400 V/µs |
| -3db带宽： | 300MHz |
| 电流 - 输入偏压： | 400nA |
| 电压 - 输入偏移： | 3000µV |
| 电流 - 电源： | 5.4mA |
| 电流 - 输出 / 通道： | 60mA |
| 电压 - 电源，单路/双路(±)： | 8 V ~ 12 V，±4 V ~ 6 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SC-74A，SOT-753 |
| 供应商设备封装： | SOT-23-5 |
| 包装： | 标准包装 |
| 产品目录页面： | 770 (CN2011-ZH PDF) |
| 其它名称： | AD8055ARTZ-REEL7DKR |
AD8055/AD8056
Rev. J | Page 12 of 16
APPLICATIONS
FOUR-LINE VIDEO DRIVER
Between these points, a feedback resistor can be used to close
the loop. As in the case of a conventional op amp inverting gain
stage, an input resistor is added to vary the gain.
The AD8055 is a useful low cost circuit for driving up to four
video lines. For such an application, the amplifier is configured
for a noninverting gain of 2, as shown in Figure 36. The input
video source is terminated in 75 Ω and is applied to the high
impedance noninverting input.
/R
The gain of this circuit from the input to AMP1 output is RF I,
while the gain to the output of AMP2 is R /R
F
I
. The circuit
therefore creates a balanced differential output signal from a
single-ended input. The advantage of this circuit is that the gain
can be changed by changing a single resistor, while still
maintaining the balanced differential outputs.
Each output cable is connected to the op amp output via a 75 Ω
series back termination resistor for proper cable termination.
The terminating resistors at the other ends of the lines divide
the output signal by 2, which is compensated for by the gain of 2
of the op amp stage.
75
+5V
–5V
AD8056
402
49.9
1
2
3
8
AMP1
5
6
7
4
AMP2
0.1F
RF
402
RI
402
10F
0.1F
10F
VIN
+VOUT
–VOUT
01
06
3-
0
37
For a single load, the differential gain error of this circuit was
measured as 0.01%, with a differential phase error of 0.02°. The
two load measurements were 0.02% and 0.03°, respectively. For
four loads, the differential gain error is 0.02%, while the
differential phase increases to 0.1°.
VOUT3
AD8055
+5V
–5V
6
7
2
3
4
75
VOUT1
VOUT2
VOUT4
0.1F
10F
75
402
VIN
010
63-
036
Figure 37. Single-Ended-to-Differential Line Driver
Figure 36. Four-Line Video Driver
LOW NOISE, LOW POWER PREAMP
SINGLE-ENDED-TO-DIFFERENTIAL LINE DRIVER
The AD8055 makes a good, low cost, low noise, low power
preamp. A gain-of-10 preamp can be made with a feedback
resistor of 909 Ω and a gain resistor of 100 Ω, as shown in
Creating differential signals from single-ended signals is
required for driving balanced, twisted pair cables, differential
input ADCs, and other applications that require differential
signals. This can be accomplished by using an inverting and a
noninverting amplifier stage to create the complementary
signals.
Figure 38. The circuit has a 3 dB bandwidth of 20 MHz.
0.1F
10F
0.1F
10F
+5V
–5V
+
AD8055 6
7
2
3
4
VOUT
RS
909
100
0
10
63
-03
8
The circuit shown in Figure 37 shows how an AD8056 can be
used to make a single-ended-to-differential converter that offers
some advantages over the architecture previously mentioned.
Each op amp is configured for unity gain by the feedback
resistors from the outputs to the inverting inputs. In addition,
each output drives the opposite op amp with a gain of 1 by
means of the crossed resistors. The result of this is that the
outputs are complementary and there is high gain in the overall
configuration.
Figure 38. Low Noise, Low Power Preamp with G = +10 and BW = 20 MHz
With a low source resistance (< approximately 100 Ω), the
major contributors to the input-referred noise of this circuit are
the input voltage noise of the amplifier and the noise of the
100 Ω resistor. These are 6 nV/√Hz and 1.2 nV/√Hz, respectively.
These values yield a total input referred noise of 6.1 nV/√Hz.
Feedback techniques similar to a conventional op amp are used
to control the gain of the circuit. From the noninverting input
of AMP1 to the output of AMP2 is an inverting gain.
相关PDF资料 |
PDF描述 |
|---|---|
| 929835-01-10-RK | CONN HEADER .100 SNGL R/A 10POS |
| 950536-6102-AR | CONN SOCKET 36POS 2MM VERT T/H |
| 929834-04-03-RK | CONN HEADER .100 SNGL STR 3POS |
| GBC03SBSN-M89 | CONN HEADER 3POS .100 RT/A SMD |
| 302-R261 | CONN HEADER R/A 26POS GOLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD8055ARTZ-REEL7 | 制造商:Analog Devices 功能描述:IC, OP-AMP, 300MHZ, 1400V/ us, SOT-23-5 |
| AD8055ARZ | 功能描述:IC OPAMP VF LDIST LN LP 8SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:1 系列:- 放大器类型:通用 电路数:4 输出类型:满摆幅 转换速率:0.028 V/µs 增益带宽积:105kHz -3db带宽:- 电流 - 输入偏压:3nA 电压 - 输入偏移:100µV 电流 - 电源:3.3µA 电流 - 输出 / 通道:12mA 电压 - 电源，单路/双路(±):2.7 V ~ 12 V，±1.35 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:14-TSSOP 包装:剪切带 (CT) 其它名称:OP481GRUZ-REELCT |
| AD8055ARZ | 制造商:Analog Devices 功能描述:Operational Amplifier (Op-Amp) IC |
| AD8055ARZ-ND | 制造商:Analog Devices 功能描述: |
| AD8055ARZ-REEL | 功能描述:IC OPAMP VF LDIST LN LP 8SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:160 系列:- 放大器类型:通用 电路数:4 输出类型:满摆幅 转换速率:10 V/µs 增益带宽积:9MHz -3db带宽:- 电流 - 输入偏压:1pA 电压 - 输入偏移:250µV 电流 - 电源:730µA 电流 - 输出 / 通道:28mA 电压 - 电源，单路/双路(±):2.7 V ~ 5.5 V，±1.35 V ~ 2.75 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC N 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。