参数资料
| 型号： | AD8061AR |
| 厂商： | Analog Devices Inc |
| 文件页数： | 9/20页 |
| 文件大小： | 0K |
| 描述： | IC OPAMP VF R-R LP 50MA 8SOIC |
| 标准包装： | 98 |
| 放大器类型： | 电压反馈 |
| 电路数： | 1 |
| 输出类型： | 满摆幅 |
| 转换速率： | 650 V/µs |
| -3db带宽： | 320MHz |
| 电流 - 输入偏压： | 3.5µA |
| 电压 - 输入偏移： | 1000µV |
| 电流 - 电源： | 6.8mA |
| 电流 - 输出 / 通道： | 50mA |
| 电压 - 电源，单路/双路(±)： | 2.7 V ~ 8 V，±1.35 V ~ 4 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SO |
| 包装： | 管件 |
Data Sheet
AD8061/AD8062/AD8063
Rev. J | Page 17 of 20
APPLICATIONS INFORMATION
SINGLE-SUPPLY SYNC STRIPPER
When a video signal contains synchronization pulses, it is
sometimes desirable to remove them prior to performing
certain operations. In the case of analog-to-digital conversion,
the sync pulses consume some of the dynamic range, so
removing them increases the converter’s available dynamic
range for the video information.
Figure 53 shows a basic circuit for creating a sync stripper using
the AD8061 powered by a single supply. When the negative
supply is at ground potential, the lowest potential to which the
output can go is ground. This feature is exploited to create a
waveform whose lowest amplitude is the black level of the video
and does not include the sync level.
75
VIDEO OUT
75
RG
1k
75
RF
1k
10F
3V
AD8061
0.1F
3
2
4
6
7
VIDEO IN
PIN NUMBERS ARE
FOR 8-LEAD PACKAGE
01065-
053
Figure 53. Single 3 V Sync Stripper Using AD8061
In this case, the input video signal has its black level at ground,
so it comes out at ground at the input. Because the sync level is
below the black level, it does not show up at the output. However,
all of the active video portion of the waveform is amplified by a
gain of 2 and then normalized to unity gain by the back-
terminated transmission line. Figure 54 is an oscilloscope plot
of the input and output waveforms.
01065-
054
500mV
INPUT
OUTPUT
1
2
10s
Figure 54. Input and Output Waveforms for a Single-Supply
Video Sync Stripper Using an AD8061
Some video signals with sync are derived from single-supply
devices, such as video DACs. These signals can contain sync,
but the whole waveform is positive, and the black level is not
at ground but at a positive voltage.
The circuit can be modified to provide the sync stripping
function for such a waveform. Instead of connecting RG to
ground, connect it to a dc voltage that is two times the black
level of the input signal. The gain from the noninverting input
to the output is 2, which means the black level is amplified by 2
to the output. However, the gain through RG is 1 to the output.
It takes a dc level of twice the input black level to shift the black
level to ground at the output. When this occurs, the sync is
stripped, and the active video is passed as in the ground-
referenced case.
75
10F
0.1F
3V
3
2
4
6
7
75
MONITOR
#1
75
1k
3V
1k
3
2
5
6
7
8
1
4
MONITOR
#2
GREEN
DAC
RED
GREEN
BLUE
RED
DAC
BLUE
DAC
75
AD8061
75
10F
0.1F
1k
AD8062
75
AD8062
75
01065-
055
Figure 55. RGB Cable Driver Using AD8061 and AD8062
RGB AMPLIFIER
Most RGB graphics signals are created by video DAC outputs
that drive a current through a resistor to ground. At the video
black level, the current goes to zero, and the voltage of the video
is also zero. Before the availability of high speed rail-to-rail op
amps, it was essential that an amplifier have a negative supply
to amplify such a signal. Such an amplifier is necessary if one
wants to drive a second monitor from the same DAC outputs.
However, high speed, rail-to-rail output amplifiers like the
AD8061 and AD8062 accept ground-level input signals and
output ground-level signals. They are used as RGB signal
amplifiers. A combination of the AD8061 (single) and the
AD8062 (dual) amplifies the three video channels of an RGB
system. Figure 55 shows a circuit that performs this function.
相关PDF资料 |
PDF描述 |
|---|---|
| 25643001RP2 | CONN RCPT 2MM VRT DUAL ROW 30POS |
| AD8040ARUZ-REEL7 | IC AMP GP R-R QUAD LP 14TSSOP |
| 7010.7020.13 | FUSE 125MA 125V 2.3X8MM W/LEAD |
| 0713085460 | CONN HEADER BKWY SMD TIN 60POS |
| 25630201RP2 | CONN RCPT 2MM VERT SGL ROW 2POS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD8061AR-EBZ | 功能描述:BOARD EVAL FOR AD8061AR RoHS:是 类别:编程器，开发系统 >> 评估板 - 运算放大器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- |
| AD8061AR-REEL | 制造商:Rochester Electronics LLC 功能描述:SOIC SINGLE,RAIL-TO-RAIL VLTG-FDBK AMP - Tape and Reel 制造商:Analog Devices 功能描述: |
| AD8061AR-REEL7 | 制造商:Analog Devices 功能描述:OP Amp Single Volt Fdbk R-R O/P 8V 8-Pin SOIC N T/R |
| AD8061ART-EBZ | 功能描述:BOARD EVAL FOR AD8061ART RoHS:是 类别:编程器，开发系统 >> 评估板 - 运算放大器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- |
| AD8061ART-R2 | 制造商:Analog Devices 功能描述:OP Amp Single Volt Fdbk R-R O/P 8V 5-Pin SOT-23 T/R 制造商:Analog Devices 功能描述:OP AMP SGL VOLT FDBK R-R O/P 8V 5PIN SOT-23 - Tape and Reel 制造商:Analog Devices 功能描述:IC OP-AMP VOLTAGE FEEDBACK |
发布紧急采购，3分钟左右您将得到回复。