- 您现在的位置：买卖IC网 > PDF目录16934 > AD8063AR-EBZ (Analog Devices Inc)BOARD EVAL FOR AD8063AR PDF资料下载
参数资料
| 型号： | AD8063AR-EBZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 7/20页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR AD8063AR |
| 标准包装： | 1 |
| 每 IC 通道数： | 1 - 单 |
| 放大器类型： | 电压反馈 |
| 板类型： | 裸（未填充） |
| 已供物品： | 板 |
| 已用 IC / 零件： | 8-SOIC 封装 |
Data Sheet
AD8061/AD8062/AD8063
Rev. J | Page 15 of 20
TIME (ns)
2.0
0
OU
TP
U
T
V
O
LT
A
G
E
(V)
2.2
2.4
2.6
2.8
3.0
3.2
3.4
3.6
4
8
12
16
20
24
28
32
2V TO 3V STEP
2.1V TO 3.1V STEP
2.2V TO 3.2V STEP
2.3V TO 3.3V STEP
2.4V TO 3.4V STEP
01065-
047
Figure 47. Output Rising Edge for 1 V Step at
Input Headroom Limits, G = 1, VS = 5 V, 0 V
As the saturation point of the output stage is approached, the
output signal shows increasing amounts of compression and
clipping. As in the input headroom case, the higher frequency
signals require a bit more headroom than lower frequency
signals. Figure 16, Figure 17, and Figure 18 illustrate this point,
plotting typical distortion vs. output amplitude and bias for
gains of 2 and 5.
OVERLOAD BEHAVIOR AND RECOVERY
Input
The specified input common-mode voltage of the AD8061/
AD8062/AD8063 is 200 mV below the negative supply to
within 1.8 V of the positive supply. Exceeding the top limit
results in lower bandwidth and increased settling time as seen
in Figure 46 and Figure 47. Pushing the input voltage of a unity-
gain follower beyond 1.6 V within the positive supply leads to
the behavior shown in Figure 48—an increasing amount of
output error and much increased settling time. Recovery time
from input voltages 1.6 V or closer to the positive supply is
approximately 35 ns, which is limited by the settling artifacts
caused by transistors in the input stage coming out of saturation.
The AD8061/AD8062/AD8063 family does not exhibit phase
reversal, even for input voltages beyond the voltage supply rails.
Going more than 0.6 V beyond the power supplies turns on
protection diodes at the input stage, which greatly increases the
current draw of the device.
TIME (ns)
2.1
0
OU
TP
U
T
V
O
LT
A
G
E
(V)
2.3
100
VOLTAGE STEP
FROM 2.4V TO 3.4V
2.5
2.7
2.9
3.1
3.3
3.5
3.7
VOLTAGE STEP
FROM 2.4V TO 3.6V
VOLTAGE STEP
FROM 2.4V TO 3.8V,
4V AND 5V
200
300
400
500
600
01065-
048
Figure 48. Pulse Response for G = 1 Follower,
Input Step Overloading the Input Stage
Output
Output overload recovery is typically within 40 ns after the
amplifier’s input is brought to a nonoverloading value. Figure 49
shows output recovery transients for the amplifier recovering
from a saturated output from the top and bottom supplies to a
point at midsupply.
TIME (ns)
–0.2
INP
UT
AND
O
UT
P
UT
V
O
LT
A
G
E
(V)
OUTPUT VOLTAGE
5V TO 2.5V
0.2
0.6
1.0
1.4
1.8
2.2
2.6
3.0
3.4
3.8
4.2
4.6
5.0
10
20
30
40
50
60
70
OUTPUT VOLTAGE
0V TO 2.5V
INPUT VOLTAGE
EDGES
R
5V
VO
2.5V
R
VIN
–
0
01065-
049
Figure 49. Overload Recovery, G = 1, VS = 5 V
相关PDF资料 |
PDF描述 |
|---|---|
| AD8063ART-EBZ | BOARD EVAL FOR AD8063ART |
| 380LX331M500A452 | CAP ALUM 330UF 500V 20% SNAP |
| EGM08DTMH-S189 | CONN EDGECARD 16POS R/A .156 SLD |
| RCC18DREH-S13 | CONN EDGECARD 36POS .100 EXTEND |
| LGN2E821MELB35 | CAP ALUM 820UF 250V 20% SNAP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD8063AR-REEL | 制造商:Analog Devices 功能描述:OP Amp Single Volt Fdbk R-R O/P 8V 8-Pin SOIC N T/R 制造商:Rochester Electronics LLC 功能描述:SOIC SNGL,R-TO-R VLTG-FDBK AMP W/DISABLE - Tape and Reel |
| AD8063AR-REEL7 | 制造商:Analog Devices 功能描述:OP Amp Single Volt Fdbk R-R O/P 8V 8-Pin SOIC N T/R |
| AD8063ART-EBZ | 功能描述:BOARD EVAL FOR AD8063ART RoHS:是 类别:编程器，开发系统 >> 评估板 - 运算放大器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- |
| AD8063ART-R2 | 制造商:Analog Devices 功能描述:OP Amp Single Volt Fdbk R-R O/P 8V 6-Pin SOT-23 T/R 制造商:Analog Devices 功能描述:OP AMP SGL VOLT FDBK R-R O/P 8V 6PIN SOT-23 - Tape and Reel 制造商:Rochester Electronics LLC 功能描述:SOT23 SNGL,RL-TO-RL V-F AMP W/DISABLE - Bulk 制造商:Analog Devices 功能描述:IC OP-AMP VOLTAGE FEEDBACK |
| AD8063ART-REEL | 制造商:Analog Devices 功能描述:OP Amp Single Volt Fdbk R-R O/P 8V 6-Pin SOT-23 T/R |
发布紧急采购，3分钟左右您将得到回复。