参数资料
| 型号： | AD8072ARMZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 3/13页 |
| 文件大小： | 0K |
| 描述： | IC OPAMP VIDEO DUAL 8MSOP |
| 标准包装： | 50 |
| 应用： | 电流反馈 |
| 电路数： | 2 |
| -3db带宽： | 100MHz |
| 转换速率： | 500 V/µs |
| 电流 - 电源： | 3.5mA |
| 电流 - 输出 / 通道： | 30mA |
| 电压 - 电源，单路/双路(±)： | 5 V ~ 12 V，±2.5 V ~ 6 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-MSOP |
| 包装： | 管件 |
REV. D
AD8072/AD8073
–10–
Crosstalk
Crosstalk between internal amplifiers may vary depending on
which amplifier is being driven and how many amplifiers are
being driven. This variation typically stems from pin location on
the package and the internal layout of the IC itself. Table I
illustrates the typical crosstalk results for a combination of
conditions.
Table I. AD8073JR Crosstalk Table (dB)
Receive Amplifier
AD8073JR
12
3
1
X
–60
–56
Drive
2
–60
X
–60
Amplifier
3
–54
–60
X
All Hostile
–53
–55
–54
CONDITIONS
VS =
±5 V
RF = 1 k
, R
L = 150
AV = 2
VOUT = 2 V p-p on Drive Amplifier
Layout Considerations
The specified high speed performance of the AD8072 and
AD8073 require careful attention to board layout and compo-
nent selection. Proper RF design techniques and low parasitic
component selection are mandatory.
The PCB should have a ground plane covering all unused portions
of the component side of the board to provide a low impedance
ground path. The ground plane should be removed from the
area near the input pins to reduce stray capacitance.
Chip capacitors should be used for supply bypassing. One end
of the capacitor should be connected to the ground plane and
the other within 1/8 inches of each power pin. An additional
large (4.7
F–10 F) tantalum electrolytic capacitor should be
connected in parallel, but not necessarily as close to the supply
pins, to provide current for fast large-signal changes at the
device’s output.
The feedback resistor should be located close to the inverting
input pin in order to keep the stray capacitance at this node to a
minimum. Capacitance variations of less than 1 pF at the invert-
ing input will affect high speed performance.
Stripline design techniques should be used for long signal traces
(greater than approximately 1 inch). These should be designed
with a characteristic impedance of 50
or 75 and be properly
terminated at each end.
相关PDF资料 |
PDF描述 |
|---|---|
| LTC1597BIG#TR | IC DAC 16BIT PAR 28SSOP |
| AD8072JRZ | IC VIDEO AMP DUAL 8-SOIC |
| LTC1597-1BIG#TR | IC DAC 16BIT PAR 28SSOP |
| AD8142ACPZ-R7 | IC AMP VIDEO TRIPLE DR 24-LFCSP |
| AD8141ACPZ-R7 | IC AMP VIDEO TRIPLE DR 24-LFCSP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD8072ARMZ-REEL | 功能描述:IC OPAMP VIDEO DUAL 8MSOP RoHS:是 类别:集成电路 (IC) >> 线性 - 放大器 - 视频放大器和频缓冲器 系列:- 标准包装:1,000 系列:- 应用:驱动器 输出类型:差分 电路数:3 -3db带宽:350MHz 转换速率:1000 V/µs 电流 - 电源:14.5mA 电流 - 输出 / 通道:60mA 电压 - 电源，单路/双路(±):5 V ~ 12 V，±2.5 V ~ 6 V 安装类型:表面贴装 封装/外壳:20-VFQFN 裸露焊盘 供应商设备封装:20-QFN 裸露焊盘（4x4） 包装:带卷 (TR) |
| AD8072ARMZ-REEL7 | 功能描述:IC OPAMP VIDEO DUAL 8MSOP RoHS:是 类别:集成电路 (IC) >> 线性 - 放大器 - 视频放大器和频缓冲器 系列:- 标准包装:1,000 系列:- 应用:驱动器 输出类型:差分 电路数:3 -3db带宽:350MHz 转换速率:1000 V/µs 电流 - 电源:14.5mA 电流 - 输出 / 通道:60mA 电压 - 电源，单路/双路(±):5 V ~ 12 V，±2.5 V ~ 6 V 安装类型:表面贴装 封装/外壳:20-VFQFN 裸露焊盘 供应商设备封装:20-QFN 裸露焊盘（4x4） 包装:带卷 (TR) |
| AD8072JN | 制造商:Rochester Electronics LLC 功能描述:PDIP LOW COST DUAL VIDEO AMPLIFIER - Bulk 制造商:Analog Devices 功能描述:VIDEO AMP DUAL LOW COST 8072 DIP8 |
| AD8072JNZ | 功能描述:IC OPAMP VIDEO DUAL 8DIP RoHS:是 类别:集成电路 (IC) >> 线性 - 放大器 - 视频放大器和频缓冲器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 应用:TFT-LCD 面板：VCOM 驱动器 输出类型:满摆幅 电路数:1 -3db带宽:35MHz 转换速率:40 V/µs 电流 - 电源:3.7mA 电流 - 输出 / 通道:1.3A 电压 - 电源，单路/双路(±):9 V ~ 20 V，±4.5 V ~ 10 V 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽）裸露焊盘 供应商设备封装:8-uMax-EP 包装:管件 |
| AD8072JR | 制造商:Analog Devices 功能描述:OP Amp Dual Current Fdbk 制造商:Rochester Electronics LLC 功能描述:SOIC LOW COST DUAL VIDEO AMPLIFIER - Bulk |
发布紧急采购，3分钟左右您将得到回复。