参数资料
| 型号： | AD811JRZ-REEL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 6/21页 |
| 文件大小： | 0K |
| 描述： | IC OPAMP VIDEO HP 8SOIC |
| 标准包装： | 2,500 |
| 应用： | 电流反馈 |
| 电路数： | 1 |
| -3db带宽： | 140MHz |
| 转换速率： | 2500 V/µs |
| 电流 - 电源： | 16.5mA |
| 电流 - 输出 / 通道： | 100mA |
| 电压 - 电源，单路/双路(±)： | ±4.5 V ~ 18 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SO |
| 包装： | 带卷 (TR) |
Data Sheet
AD811
Rev. F | Page 13 of 20
Driving Capacitive Loads
The feedback and gain resistor values in Table 3 result in very
flat closed-loop responses in applications where the load
capacitances are below 10 pF. Capacitances greater than this
result in increased peaking and overshoot, although not
necessarily in a sustained oscillation.
There are at least two very effective ways to compensate for this
effect. One way is to increase the magnitude of the feedback
resistor, which lowers the 3 dB frequency. The other method is
to include a small resistor in series with the output of the ampli-
fier to isolate it from the load capacitance. The results of these
two techniques are illustrated in Figure 38. Using a 1.5 k
feedback resistor, the output ripple is less than 0.5 dB when
driving 100 pF. The main disadvantage of this method is that it
sacrifices a little bit of gain flatness for increased capacitive load
drive capability. With the second method, using a series resistor,
the loss of flatness does not occur.
Figure 37. Recommended Connection for Driving a Large Capacitive Load
Figure 38. Performance Comparison of Two Methods
for Driving a Capacitive Load
Figure 39. Recommended Value of Series Resistor vs.
the Amount of Capacitive Load
Figure 39 shows recommended resistor values for different load
capacitances. Refer again to Figure 38 for an example of the
results of this method. Note that it may be necessary to adjust
the gain setting resistor, RG, to correct for the attenuation which
results due to the divider formed by the series resistor, RS, and
the load resistance.
Applications that require driving a large load capacitance at a
high slew rate are often limited by the output current available
from the driving amplifier. For example, an amplifier limited to
25 mA output current cannot drive a 500 pF load at a slew rate
greater than 50 V/s. However, because of the 100 mA output
current of the AD811, a slew rate of 200 V/s is achievable
when driving the same 500 pF capacitor, as shown in Figure 40.
Figure 40. Output Waveform of an AD811 Driving a 500 pF Load.
Gain = +2, RFB = 649 , RS = 15 , RS = 10 k
AD811
+
–
7
6
4
2
3
RS (OPTIONAL)
CL
RL
VOUT
–VS
+VS
RFB
RG
RT
VIN
0.1
F
0.1
F
00866-E-038
–6
–3
0
3
6
9
12
GAIN
(dB)
FREQUENCY (MHz)
1
10
100
00866-E-039
VS = ±15V
CL = 100pF
RL = 10k
GAIN = +2
RFB = 1.5k
RS = 0
RFB = 649
RS = 30
0
10
20
30
40
50
60
70
80
90
100
VALUE
OF
R
S
(
)
LOAD CAPACITANCE (pF)
10
100
1000
00866-E-040
GAIN = +2
VS = ±15V
RS VALUE SPECIFIED
IS FOR FLATTEST
FREQUENCY RESPONSE
00866-E-041
10
90
100
0%
5V
2V
100ns
VIN
VOUT
相关PDF资料 |
PDF描述 |
|---|---|
| VI-J1W-MW-S | CONVERTER MOD DC/DC 5.5V 100W |
| VI-B34-MU-F3 | CONVERTER MOD DC/DC 48V 200W |
| 1-796375-1 | CONN RCPT 9POS GOLD |
| MAX5525ETC+ | IC DAC 10BIT DUAL ULP 12-TQFN |
| VE-J5Y-MZ-B1 | CONVERTER MOD DC/DC 3.3V 16.5W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD811JRZ-REEL7 | 功能描述:IC OPAMP VIDEO HP 8SOIC RoHS:是 类别:集成电路 (IC) >> 线性 - 放大器 - 视频放大器和频缓冲器 系列:- 标准包装:1,000 系列:- 应用:驱动器 输出类型:差分 电路数:3 -3db带宽:350MHz 转换速率:1000 V/µs 电流 - 电源:14.5mA 电流 - 输出 / 通道:60mA 电压 - 电源，单路/双路(±):5 V ~ 12 V，±2.5 V ~ 6 V 安装类型:表面贴装 封装/外壳:20-VFQFN 裸露焊盘 供应商设备封装:20-QFN 裸露焊盘（4x4） 包装:带卷 (TR) |
| AD811SCHIPS | 制造商:AD 制造商全称:Analog Devices 功能描述:High Performance Video Op Amp |
| AD811SE | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| AD811SE/883B | 功能描述:视频放大器 OP-AMP HI-SPEED VIDEO RoHS:否 制造商:ON Semiconductor 通道数量:4 电源类型: 工作电源电压:3.3 V, 5 V 电源电流: 最小工作温度: 最大工作温度: 封装 / 箱体:TSSOP-14 封装:Reel 安装风格: |
| AD811SQ/883B | 功能描述:视频放大器 OP-AMP HIGH SPEED VIDEO RoHS:否 制造商:ON Semiconductor 通道数量:4 电源类型: 工作电源电压:3.3 V, 5 V 电源电流: 最小工作温度: 最大工作温度: 封装 / 箱体:TSSOP-14 封装:Reel 安装风格: |
发布紧急采购，3分钟左右您将得到回复。