参数资料
| 型号： | AD8130ARMZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 30/41页 |
| 文件大小： | 0K |
| 描述： | IC AMP DIFF LN LDIST 40MA 8MSOP |
| 设计资源： | High CMRR Circuit for Converting Wideband Complementary DAC Outputs to Single-Ended Without Precision Resistors (CN0142) |
| 标准包装： | 50 |
| 放大器类型： | 差分 |
| 电路数： | 1 |
| 转换速率： | 1100 V/µs |
| -3db带宽： | 290MHz |
| 电流 - 输入偏压： | 500nA |
| 电压 - 输入偏移： | 400µV |
| 电流 - 电源： | 13mA |
| 电流 - 输出 / 通道： | 40mA |
| 电压 - 电源，单路/双路(±)： | 4.5 V ~ 25.2 V，±2.25 V ~ 12.6 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-MSOP |
| 包装： | 管件 |
| 产品目录页面： | 765 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页当前第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页
AD8129/AD8130
Rev. C | Page 35 of 40
One way to accomplish this is to drive both REF and RG with
the desired offset signal (see Figure 139). Superposition can be
used to solve this circuit. First, break the connection between
VOFFSET and RG. With RG grounded, the gain from Pin 4 to VOUT
is 1 + RF/RG. With Pin 4 grounded, the gain though RG to VOUT
is RF/RG. The sum of these is 1. If VREF is delivered from a low
impedance source, this works fine. However, if the delivered
offset voltage is derived from a high impedance source, such as
a voltage divider, its impedance affects the gain equation. This
makes the circuit more complicated because it creates an
interaction between the gain and offset voltage.
VOUT =
VIN × (1 + RF/RG)+VOFFSET
–V
+V
VIN
VOFFSET
–VS
PD
+VS
+
RF
RG
AD8129/
AD8130
6
2
5
4
8
1
37
0.1
μF
10
μF
0.1
μF
10
μF
02464-140
Figure 139. In this Circuit, VOFFSET Appears at the Output with Unity Gain. This
Circuit Works Well if the VOFFSET Source Impedance Is Low.
A way around this is to apply the offset voltage to a voltage
divider whose attenuation factor matches the gain of the
amplifier and then apply this voltage to the high impedance
REF input. This circuit first divides the desired offset voltage
by the gain, and the amplifier multiplies it back up to unity (see
VOUT =
VIN × (1 + RF/RG)+VOFFSET
–V
+V
VIN
–VS
PD
+VS
+
RF
RG
VOFFSET
RF
AD8129/
AD8130
6
2
5
4
8
1
37
0.1
μF
10
μF
0.1
μF
10
μF
02464-141
Figure 140. Adding an Attenuator at the Offset Input Causes It to Appear at
the Output with Unity Gain.
RESISTORLESS GAIN OF 2
The voltage applied to the REF input (Pin 4) can also be a high
bandwidth signal. If a unity-gain AD8130 has both +IN and
REF driven with the same signal, there is unity gain from VIN
and unity gain from VREF. Thus, the circuit has a gain of 2 and
requires no resistors (see Figure 141).
VOUT
–V
+V
VIN
–VS
PD
+VS
+
AD8130
6
2
5
4
8
1
37
0.1
μF
10
μF
0.1
μF10μF
02464-142
Figure 141. Gain-of-2 Connections with No Resistors
SUMMER
A general summing circuit can be made by the previous
technique. A unity-gain configured AD8130 has one signal
applied to +IN, while the other signal is applied to REF. The
output is the sum of the two input signals (see Figure 142).
VOUT = V1 + V2
V1
V2
–V
+V
–VS
+VS
+
AD8130
6
2
5
4
8
1
37
0.1
μF
10
μF
0.1
μF10μF
02464-143
PD
Figure 142. A Summing Circuit that is Noninverting
with High Input Impedance
This circuit offers several advantages over a conventional op
amp inverting summing circuit. First, the inputs are both high
impedance and the circuit is noninverting. It would require
significant additional circuitry to make an op amp summing
circuit that has high input impedance and is noninverting.
Another advantage is that the AD8130 circuit still preserves the
full bandwidth of the part. In a conventional summing circuit,
the noise gain is increased for each additional input, so the
bandwidth response decreases accordingly. By this technique,
four signals can be summed by applying them to two AD8130s
and then summing the two outputs by a third AD8130.
CABLE-TAP AMPLIFIER
It is often desirable to have a video signal drive several pieces of
equipment. However, the cable should only be terminated once at
its endpoint; therefore, it is not appropriate to have a termination
at each device. A loop-through connection allows a device to tap
the video signal while not disturbing it by any excessive loading.
相关PDF资料 |
PDF描述 |
|---|---|
| AD8130ARZ | IC AMP DIFF LN LDIST 40MA 8SOIC |
| OP491GRUZ-REEL | IC OPAMP GP R-R 3MHZ 14TSSOP |
| LTC6247CMS8#PBF | IC OPAMP R-R 120MHZ DUAL 8MSOP |
| SSM2143PZ | IC AUDIO RX MONO AB DIFF 8DIP |
| SSM2143SZ | IC AUDIO RX MONO AB DIFF 8SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD8130ARMZ | 制造商:Analog Devices 功能描述:Operational Amplifier (Op-Amp) IC |
| AD8130ARMZ-REEL | 功能描述:IC AMP DIFF LN LDIST 40MA 8MSOP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:- 放大器类型:通用 电路数:2 输出类型:满摆幅 转换速率:1.8 V/µs 增益带宽积:6.5MHz -3db带宽:4.5MHz 电流 - 输入偏压:5nA 电压 - 输入偏移:100µV 电流 - 电源:65µA 电流 - 输出 / 通道:35mA 电压 - 电源，单路/双路(±):1.8 V ~ 5.25 V，±0.9 V ~ 2.625 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| AD8130ARMZ-REEL7 | 功能描述:IC AMP DIFF LN LDIST 40MA 8MSOP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:- 放大器类型:通用 电路数:2 输出类型:满摆幅 转换速率:1.8 V/µs 增益带宽积:6.5MHz -3db带宽:4.5MHz 电流 - 输入偏压:5nA 电压 - 输入偏移:100µV 电流 - 电源:65µA 电流 - 输出 / 通道:35mA 电压 - 电源，单路/双路(±):1.8 V ~ 5.25 V，±0.9 V ~ 2.625 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| AD8130AR-REEL | 制造商:Analog Devices 功能描述:SP Amp DIFF Receiver Amp Single 制造商:Rochester Electronics LLC 功能描述:SOIC LO-COST HI-SPD DIFFERENT'L RECEIVER - Tape and Reel |
| AD8130AR-REEL1 | 制造商:AD 制造商全称:Analog Devices 功能描述:Low-Cost 270 MHz Differential Receiver Amplifiers |
发布紧急采购，3分钟左右您将得到回复。