参数资料
| 型号： | AD8131ARMZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 9/21页 |
| 文件大小： | 0K |
| 描述： | IC AMP DIFF LDIST 60MA 8MSOP |
| 标准包装： | 50 |
| 放大器类型： | 差分 |
| 电路数： | 1 |
| 输出类型： | 差分 |
| 转换速率： | 2000 V/µs |
| -3db带宽： | 400MHz |
| 电流 - 输入偏压： | 500nA |
| 电压 - 输入偏移： | 1500µV |
| 电流 - 电源： | 11.5mA |
| 电流 - 输出 / 通道： | 60mA |
| 电压 - 电源，单路/双路(±)： | 2.8 V ~ 11 V，±1.4 V ~ 5.5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-MSOP |
| 包装： | 管件 |
| 产品目录页面： | 765 (CN2011-ZH PDF) |
AD8131
Rev. B | Page 16 of 20
THEORY OF OPERATION
The AD8131 differs from conventional op amps in that it has
two outputs whose voltages move in opposite directions. Like
an op amp, it relies on high open-loop gain and negative
feedback to force these outputs to the desired voltages. The
AD8131 behaves much like a standard voltage feedback op amp
and makes it easy to perform single-ended-to-differential
conversion, common-mode level-shifting, and amplification of
differential signals.
Previous discrete and integrated differential driver designs used
two independent amplifiers and two independent feedback
loops, one to control each of the outputs. When these circuits
are driven from a single-ended source, the resulting outputs are
typically not well balanced. Achieving a balanced output
typically required exceptional matching of the amplifiers and
feedback networks.
DC common-mode level shifting has also been difficult with
previous differential drivers. Level shifting required the use of a
third amplifier and feedback loop to control the output
common-mode level. Sometimes the third amplifier has also
been used to attempt to correct an inherently unbalanced
circuit. Excellent performance over a wide frequency range has
proven difficult with this approach.
The AD8131 uses two feedback loops to separately control the
differential and common-mode output voltages. The differential
feedback, set by internal resistors, controls only the differential
output voltage. The common-mode feedback controls only the
common-mode output voltage. This architecture makes it easy
to arbitrarily set the common-mode output level. It is forced, by
internal common-mode feedback, to be equal to the voltage
applied to the VOCM input, without affecting the differential
output voltage.
The AD8131 architecture results in outputs that are very highly
balanced over a wide frequency range without requiring
external components or adjustments. The common-mode
feedback loop forces the signal component of the output
common-mode voltage to be zeroed. The result is nearly
perfectly balanced differential outputs, of identical amplitude
and exactly 180 degrees apart in phase.
ANALYZING AN APPLICATION CIRCUIT
The AD8131 uses high open-loop gain and negative feedback to
force its differential and common-mode output voltages in such
a way as to minimize the differential and common-mode error
voltages. The differential error voltage is defined as the voltage
between the differential inputs labeled +IN and IN in
Figure 39. For most purposes, this voltage can be assumed to be
zero. Similarly, the difference between the actual output
common-mode voltage and the voltage applied to VOCM can also
be assumed to be zero. Starting from these two assumptions,
any application circuit can be analyzed.
CLOSED-LOOP GAIN
The differential mode gain of the circuit in Figure 39 can be
described by the following equation:
2
=
G
F
dm
IN,
dm
OUT,
R
V
where RF = 1.5 kΩ and RG = 750 Ω nominally.
ESTIMATING THE OUTPUT NOISE VOLTAGE
Similar to the case of a conventional op amp, the differential
output errors (noise and offset voltages) can be estimated by
multiplying the input referred terms, at +IN and IN, by the
circuit noise gain. The noise gain is defined as
3
1
=
+
=
G
F
N
R
G
The total output referred noise for the AD8131, including the
contributions of RF, RG, and op amp, is nominally 25 nV/√Hz
at 20 MHz.
CALCULATING THE INPUT IMPEDANCE OF AN
APPLICATION CIRCUIT
The effective input impedance of a circuit such as that in
amplifier is being driven by a single-ended or differential signal
source. For balanced differential input signals, the input
impedance (RIN, dm) between the inputs (+DIN and DIN) is
Ω
=
×
=
k
5
.
1
2
,
G
dm
IN
R
In the case of a single-ended input signal (for example if DIN is
grounded and the input signal is applied to +DIN), the input
impedance becomes
()
Ω
=
+
×
=
k
125
.
1
2
1
,
F
G
F
G
dm
IN
R
The input impedance is effectively higher than it would be for a
conventional op amp connected as an inverter because a
fraction of the differential output voltage appears at the inputs
as a common-mode signal, partially bootstrapping the voltage
across the input resistor RG.
相关PDF资料 |
PDF描述 |
|---|---|
| LT1990AIS8#PBF | IC AMP DIFF +/-250V MCRPWR 8SOIC |
| ADA4004-1ARZ | IC OPAMP GP 12MHZ PREC 8SOIC |
| OP90GSZ | IC OPAMP GP PREC 8SOIC |
| OP90GPZ | IC OPAMP GP PREC 8DIP |
| LTC6416IDDB#TRMPBF | IC DIFF 16BIT BUFFER 10-DFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD8131ARMZ | 制造商:Analog Devices 功能描述:IC DIFF AMP 400MHZ 2000V/US 8MSOP |
| AD8131ARMZ-REEL | 功能描述:IC AMP DIFF LDIST 60MA 8MSOP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:- 放大器类型:通用 电路数:2 输出类型:满摆幅 转换速率:1.8 V/µs 增益带宽积:6.5MHz -3db带宽:4.5MHz 电流 - 输入偏压:5nA 电压 - 输入偏移:100µV 电流 - 电源:65µA 电流 - 输出 / 通道:35mA 电压 - 电源，单路/双路(±):1.8 V ~ 5.25 V，±0.9 V ~ 2.625 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| AD8131ARMZ-REEL7 | 功能描述:IC AMP DIFF LDIST 60MA 8MSOP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 产品培训模块:Differential Circuit Design Techniques for Communication Applications 标准包装:1 系列:- 放大器类型:RF/IF 差分 电路数:1 输出类型:差分 转换速率:9800 V/µs 增益带宽积:- -3db带宽:2.9GHz 电流 - 输入偏压:3µA 电压 - 输入偏移:- 电流 - 电源:40mA 电流 - 输出 / 通道:- 电压 - 电源，单路/双路(±):3 V ~ 3.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-VQFN 裸露焊盘，CSP 供应商设备封装:16-LFCSP-VQ 包装:剪切带 (CT) 产品目录页面:551 (CN2011-ZH PDF) 其它名称:ADL5561ACPZ-R7CT |
| AD8131AR-REEL | 制造商:Analog Devices 功能描述:SP Amp DIFF Line Driver Amp Single 制造商:Rochester Electronics LLC 功能描述:SOIC LO-COST HI-SPD DIFFERENTIAL DRIVER - Tape and Reel |
| AD8131AR-REEL7 | 制造商:Analog Devices 功能描述:SP Amp DIFF Line Driver Amp Single 制造商:Analog Devices 功能描述:SP Amp DIFF Line Driver Amp Single ±5.5V/11V 8-Pin SOIC N T/R 制造商:Rochester Electronics LLC 功能描述:SOIC LO-COST HI-SPD DIFFERENTIAL DRIVER - Tape and Reel |
发布紧急采购，3分钟左右您将得到回复。