参数资料
| 型号： | AD8138ARZ-R7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 14/25页 |
| 文件大小： | 0K |
| 描述： | IC AMP DIFF LDIST LP 95MA 8SOIC |
| 设计资源： | DC-Coupled, Single-Ended-to-Differential Conversion Using AD8138 and AD7352 (CN0040) DC-Coupled, Single-Ended-to-Differential Conversion Using AD8138 and AD7356 (CN0041) DC-Coupled, Single-Ended-to-Differential Conversion Using AD8138 and AD7357 (CN0061) |
| 标准包装： | 1,000 |
| 类型： | ADC 驱动器 |
| 应用： | 数据采集 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SO |
| 包装： | 带卷 (TR) |
AD8138
Rev. F | Page 20 of 24
BALANCED TRANSFORMER DRIVER
Transformers are among the oldest devices used to perform a
single-ended-to-differential conversion (and vice versa). Trans-
formers can also perform the additional functions of galvanic
isolation, step-up or step-down of voltages, and impedance
transformation. For these reasons, transformers always find
uses in certain applications.
However, when driving the transformer in a single-ended
manner, there is an imbalance at the output due to the parasitics
inherent in the transformer. The primary (or driven) side of the
transformer has one side at dc potential (usually ground), while
the other side is driven. This can cause problems in systems that
require good balance of the transformer’s differential output
signals.
If the interwinding capacitance (CSTRAY) is assumed to be
uniformly distributed, a signal from the driving source couples
to the secondary output terminal that is closest to the primary’s
driven side. On the other hand, no signal is coupled to the
opposite terminal of the secondary because its nearest primary
terminal is not driven (see Figure 43). The exact amount of this
imbalance depends on the particular parasitics of the trans-
former, but is mostly a problem at higher frequencies.
The balance of a differential circuit can be measured by
connecting an equal-valued resistive voltage divider across the
differential outputs and then measuring the center point of the
circuit with respect to ground. Since the two differential outputs
are supposed to be of equal amplitude, but 180° opposite phase,
there should be no signal present for perfectly balanced outputs.
The circuit in Figure 43 shows a Mini-Circuits T1-6T
transformer connected with its primary driven single-endedly
and the secondary connected with a precision voltage divider
across its terminals. The voltage divider is made up of two
500 Ω, 0.005% precision resistors. The voltage VUNBAL, which is
also equal to the ac common-mode voltage, is a measure of how
closely the outputs are balanced.
Figure 45 compares the transformer being driven single-
endedly by a signal generator and being driven differentially
using an AD8138. The top signal trace of Figure 45 shows the
balance of the single-ended configuration, while the bottom
shows the differentially driven balance response. The 100 MHz
balance is 35 dB better when using the AD8138.
The well-balanced outputs of the AD8138 provide a drive signal
to each of the transformer’s primary inputs that are of equal
amplitude and 180° out of phase. Therefore, depending on how
the polarity of the secondary is connected, the signals that
conduct across the interwinding capacitance either both assist
the transformer’s secondary signal equally, or both buck the
secondary signals. In either case, the parasitic effect is
symmetrical and provides a well-balanced transformer output
(see Figure 45).
PRIMARY
CSTRAY
52.3
SECONDARY VDIFF
500
0.005%
500
0.005%
VUNBAL
SIGNALIS COUPLED
ON THIS SIDE VIA CSTRAY
NO SIGNAL IS COUPLED
ON THIS SIDE
01
07
3-
0
42
Figure 43. Transformer Single-Ended-to-Differential Converter Is Inherently
Imbalanced
VDIFF
VUNBAL
AD8138
+IN
–IN
OUT+
OUT–
499
49.9
500
0.005%
500
0.005%
CSTRAY
01
07
3-
0
43
Figure 44. AD8138 Forms a Balanced Transformer Driver
FREQUENCY (MHz)
0
O
UT
P
UT
BAL
ANCE
E
RRO
R
(
d
B) –20
–40
–60
–80
–100
0.3
1
10
100
500
VUNBAL, DIFFERENTIAL DRIVE
VUNBAL, FOR TRANSFORMER
WITH SINGLE-ENDED DRIVE
0
10
73
-04
4
相关PDF资料 |
PDF描述 |
|---|---|
| ADA4938-1ACPZ-RL | IC ADC DRIVER DIFF 16-LFCSP |
| VI-2TV-MW-B1 | CONVERTER MOD DC/DC 5.8V 100W |
| AD7398BRU-REEL7 | IC DAC 12BIT QUAD SRL 16-TSSOP |
| ADA4937-1YCPZ-RL | IC ADC DIFF DRIVER 16-LFCSP |
| VE-24N-IV-F1 | CONVERTER MOD DC/DC 18.5V 150W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD8138ARZ-RL | 功能描述:IC AMP DIFF LDIST LP 95MA 8SOIC RoHS:是 类别:集成电路 (IC) >> 线性 - 放大器 - 专用 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:60 系列:- 类型:可变增益放大器 应用:CATV 安装类型:表面贴装 封装/外壳:20-WQFN 裸露焊盘 供应商设备封装:20-TQFN-EP（5x5） 包装:托盘 |
| AD8138-EVAL | 制造商:AD 制造商全称:Analog Devices 功能描述:Low Distortion Differential ADC Driver |
| AD8138SRMZ-EP-R7 | 功能描述:IC ADC DRIVER DIFF 8MSOP RoHS:是 类别:集成电路 (IC) >> 线性 - 放大器 - 专用 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:60 系列:- 类型:可变增益放大器 应用:CATV 安装类型:表面贴装 封装/外壳:20-WQFN 裸露焊盘 供应商设备封装:20-TQFN-EP（5x5） 包装:托盘 |
| AD8139 | 制造商:AD 制造商全称:Analog Devices 功能描述:Low Noise, Rail-to-Rail, Differential ADC Driver |
| AD8139_07 | 制造商:AD 制造商全称:Analog Devices 功能描述:Low Noise, Rail-to-Rail, Differential ADC Driver |
发布紧急采购，3分钟左右您将得到回复。