- 您现在的位置：买卖IC网 > PDF目录373939 > AD815 (Electronic Theatre Controls, Inc.) SILICON DUAL DIFFERNTIAL AMPLIFIER TRANSISTORS PDF资料下载
参数资料
| 型号： | AD815 |
| 厂商： | Electronic Theatre Controls, Inc. |
| 英文描述： | SILICON DUAL DIFFERNTIAL AMPLIFIER TRANSISTORS |
| 中文描述： | 硅晶体管放大器双DIFFERNTIAL |
| 文件页数： | 13/16页 |
| 文件大小： | 333K |
| 代理商： | AD815 |
AD815
REV. B
–13–
6
4
5
8
+15V
10
7
–15V
R
F
499
V
R
L
9
11
0.1
m
F
10
m
F
R
G
100
V
R
F
499
V
0.1
m
F
10
m
F
1/2
AD815
1
8
+15V
0.1
m
F
2
1k
V
4
–15V
1k
V
7
0.1
m
F
6
5
1k
V
3
1/2
AD815
1/2
1/2
AD826
100
V
100
V
1k
V
Figure 50. Differential Driver with Single-Ended
Differential Converter
Another means for creating a differential signal from a single-
ended signal is to use a transformer with a center-tapped
secondary. The center tap of the transformer is grounded and
the two secondary windings are connected to obtain opposite
polarity signals to the two inputs of the AD815 amplifiers. The
bias currents for the AD815 inputs are provided by the center
tap ground connection through the transformer windings.
One advantage of using a transformer is its ability to provide
isolation between circuit sections and to provide good common-
mode rejection. The disadvantages are that transformers have
no dc response and can sometimes be large, heavy, and expensive.
This circuit is shown in Figure 51.
6
4
5
8
+15V
10
7
–15V
R
L
9
11
0.1
m
F
10
m
F
200
V
0.1
m
F
10
m
F
1/2
AD815
1k
V
1k
V
1/2
AD815
50
V
100
V
100
V
50
V
Figure 51. Differential Driver with Transformer Input
Direct Single-Ended-to-Differential Conversion
Two types of circuits can create a differential output signal from
a single-ended input without the use of any other components
than resistors. The first of these is illustrated in Figure 52.
6
4
5
8
+15V
10
7
–15V
R
F1
402
V
R
L
9
11
R
G
100
V
R
F2
499
V
1/2
AD815
1/2
AD815
V
IN
V
OUT
AMP 1
AMP 2
Figure 52. Direct Single-Ended-to-Differential Conversion
Amp 1 has its + input driven with the input signal, while the
+ input of Amp 2 is grounded. Thus the – input of Amp 2 is
driven to virtual ground potential by its output. Therefore
Amp 1 is configured for a noninverting gain of five, (1 + R
F1
/R
G
),
because R
G
is connected to the virtual ground of Amp 2’s – input.
When the + input of Amp 1 is driven with a signal, the same
signal appears at the – input of Amp 1. This signal serves as an
input to Amp 2 configured for a gain of –5, (–R
F2
/R
G
). Thus the
two outputs move in opposite directions with the same gain and
create a balanced differential signal.
This circuit can work at various gains with proper resistor
selection. But in general, in order to change the gain of the
circuit, at least two resistor values will have to be changed. In
addition, the noise gain of the two op amps in this configuration
will always be different by one, so the bandwidths will not match.
A second circuit that has none of the disadvantages mentioned
in the above circuit creates a differential output voltage feedback
op amp out of the pair of current feedback op amps in the AD815.
This circuit, drawn in Figure 53, can be used as a high power
differential line driver, such as required for ADSL (asymmetrical
digital subscriber loop) line driving.
Each of the AD815’s op amps is configured as a unity gain
follower by the feedback resistors (R
A
). Each op amp output
also drives the other as a unity gain inverter via the two R
B
s,
creating a totally symmetrical circuit.
If the + input to Amp 2 is grounded and a small positive signal
is applied to the + input of Amp 1, the output of Amp 1 will be
driven to saturation in the positive direction and the output of
Amp 2 driven to saturation in the negative direction. This is
similar to the way a conventional op amp behaves without any
feedback.
相关PDF资料 |
PDF描述 |
|---|---|
| AD815ARB-24-REEL | High Output Current Differential Driver |
| AD815-EB | High Output Current Differential Driver |
| AD815AVR | High Output Current Differential Driver |
| AD815AY | High Output Current Differential Driver |
| AD815AYS | High Output Current Differential Driver |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD815_05 | 制造商:AD 制造商全称:Analog Devices 功能描述:High Output Current Differential Driver |
| AD8150 | 制造商:AD 制造商全称:Analog Devices 功能描述:33 x 17, 1.5 Gbps Digital Crosspoint Switch |
| AD8150AST | 制造商:Rochester Electronics LLC 功能描述:LQFP 1.5GBPS 33X17 DIGITAL CROSSPOINT SW - Tape and Reel 制造商:Analog Devices 功能描述:IC SWITCH CROSSPOINT |
| AD8150ASTZ | 功能描述:IC CROSSPOINT SWIT 33X17 184LQFP RoHS:是 类别:集成电路 (IC) >> 接口 - 模拟开关，多路复用器，多路分解器 系列:XStream™ 应用说明:Ultrasound Imaging Systems Application Note 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:250 系列:- 功能:开关 电路:单刀单掷 导通状态电阻:48 欧姆 电压电源:单电源 电压 - 电源，单路/双路(±):2.7 V ~ 5.5 V 电流 - 电源:5µA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:48-LQFP 供应商设备封装:48-LQFP（7x7） 包装:托盘 |
| AD8150ASTZ | 制造商:Analog Devices 功能描述:IC DIGITAL CROSSPOINT SWITCH |
发布紧急采购，3分钟左右您将得到回复。