参数资料
| 型号： | AD8202WYRMZ-RL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 4/20页 |
| 文件大小： | 0K |
| 描述： | IC AMP DIFF 50KHZ 8MSOP |
| 产品培训模块： | Current Sense Amplifiers |
| 标准包装： | 3,000 |
| 放大器类型： | 差分 |
| 电路数： | 1 |
| 转换速率： | 0.28 V/µs |
| 增益带宽积： | 50kHz |
| 电流 - 输入偏压： | 40nA |
| 电压 - 输入偏移： | 2000µV |
| 电流 - 电源： | 250µA |
| 电压 - 电源，单路/双路(±)： | 3.5 V ~ 12 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-MSOP |
| 包装： | 带卷 (TR) |
AD8202
Data Sheet
Rev. H | Page 12 of 20
THEORY OF OPERATION
The AD8202 consists of a preamp and buffer arranged as shown
in Figure 40. Like-named resistors have equal values.
The preamp uses a dynamic bridge (subtractor) circuit.
Identical networks (within the shaded areas), consisting of RA,
RB, RC, and RG, attenuate input signals applied to Pin 1 and
Pin 8. When equal amplitude signals are asserted at Input 1 and
Input 8, and the output of A1 is equal to the common potential
(that is, 0), the two attenuators form a balanced-bridge network.
When the bridge is balanced, the differential input voltage at
A1, and thus its output, is 0.
Any common-mode voltage applied to both inputs keeps the
bridge balanced and the A1 output at 0. Because the resistor
networks are carefully matched, the common-mode signal
rejection approaches this ideal state.
However, if the signals applied to the inputs differ, the result is a
difference at the input to A1. A1 responds by adjusting its output
to drive RB, by way of RG, to adjust the voltage at its inverting
input until it matches the voltage at its noninverting input.
By attenuating voltages at Pin 1 and Pin 8, the amplifier inputs
are held within the power supply range, even if Pin 1 and Pin 8
input levels exceed the supply or fall below common (ground).
The input network also attenuates normal (differential) mode
voltages. RC and RG form an attenuator that scales A1 feedback,
forcing large output signals to balance relatively small differen-
tial inputs. The resistor ratios establish the preamp gain at 10.
Because the differential input signal is attenuated and then
amplified to yield an overall gain of 10, Amplifier A1 operates
at a higher noise gain, multiplying deficiencies such as input
offset voltage and noise with respect to Pin 1 and Pin 8.
A1
A3
RCM
(TRIMMED)
100k
RA
–IN
RG
RC
RB
RA
RC
RB
RG
+IN
COM
A2
RF
AD8202
5
4
3
1
2
8
04981-014
Figure 40. Simplified Schematic
To minimize these errors while extending the common-mode
range, a dedicated feedback loop is used to reduce the range of
common-mode voltage applied to A1 for a given overall range at
the inputs. By offsetting the voltage range applied to the com-
pensator, the input common-mode range is also offset to include
voltages more negative than the power supply.
Amplifier A3 detects the common-mode signal applied to A1
and adjusts the voltage on the matched RCM resistors to reduce
the common-mode voltage range at the A1 inputs. By adjusting
the common voltage of these resistors, the common-mode input
range is extended while, at the same time, the normal mode
signal attenuation is reduced, leading to better performance
referred to input.
The output of the dynamic bridge taken from A1 is connected
to Pin 3 by way of a 100 k series resistor, provided for low-
pass filtering and gain adjustment. The resistors in the input
networks of the preamp and the buffer feedback resistors are
ratio-trimmed for high accuracy.
The output of the preamp drives a gain-of-2 buffer amplifier,
A2, implemented with carefully matched feedback resistors (RF).
The 2-stage system architecture of the AD8202 enables the user
to incorporate a low-pass filter prior to the output buffer. By
separating the gain into two stages, a full-scale, rail-to-rail
signal from the preamp can be filtered at Pin 3, and a half-scale
signal, resulting from filtering, can be restored to full scale by
the output buffer amp. The source resistance seen by the
inverting input of A2 is approximately 100 k to minimize the
effects of the input bias current of A2. However, this current is
quite small, and errors resulting from applications that mismatch
the resistance are correspondingly small.
The A2 input bias current has a typical value of 40 nA, however,
this can increase under certain conditions. For example, if the
input signal to the A2 amplifier is VCC/2, the output attempts to
go to VCC due to the gain of 2. However, the output saturates
because the maximum specified voltage for correct operation is
200 mV below VCC. Under these conditions, the total input bias
current increases (see Figure 41 for more information).
相关PDF资料 |
PDF描述 |
|---|---|
| M80-8870605 | CONN RECEPT 2MM VERT PCB 6POS |
| LTC6104IMS8#TRPBF | IC AMP CURRENT SENSE 8-MSOP |
| 950434-6102-AR | CONN SOCKET 34POS 2MM VERT T/H |
| OP184FSZ-REEL | IC OPAMP GP R-R 4.25MHZ LN 8SOIC |
| RGH2012-2E-P-222-B | RES 2.2K OHM .1% 1/4W 0805 SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD8202WYRZ | 功能描述:IC AMP DIFF 50KHZ 8SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:1 系列:- 放大器类型:通用 电路数:4 输出类型:满摆幅 转换速率:0.028 V/µs 增益带宽积:105kHz -3db带宽:- 电流 - 输入偏压:3nA 电压 - 输入偏移:100µV 电流 - 电源:3.3µA 电流 - 输出 / 通道:12mA 电压 - 电源，单路/双路(±):2.7 V ~ 12 V，±1.35 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:14-TSSOP 包装:剪切带 (CT) 其它名称:OP481GRUZ-REELCT |
| AD8202WYRZ-RL | 功能描述:IC AMP DIFF 50KHZ 8SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:1,000 系列:- 放大器类型:电压反馈 电路数:4 输出类型:满摆幅 转换速率:33 V/µs 增益带宽积:20MHz -3db带宽:30MHz 电流 - 输入偏压:2nA 电压 - 输入偏移:3000µV 电流 - 电源:2.5mA 电流 - 输出 / 通道:30mA 电压 - 电源，单路/双路(±):4.5 V ~ 16.5 V，±2.25 V ~ 8.25 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SOIC 包装:带卷 (TR) |
| AD8202YCSURF | 制造商:AD 制造商全称:Analog Devices 功能描述:High Common-Mode Voltage, Single-Supply Difference Amplifier |
| AD8202YR | 制造商:Analog Devices 功能描述:SP Amp DIFF AMP Single 12V 8-Pin SOIC N Tube 制造商:Analog Devices 功能描述:IC AMP DIFFERENTIAL |
| AD8202YRM | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
发布紧急采购，3分钟左右您将得到回复。