参数资料
| 型号： | AD8206YRZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 16/16页 |
| 文件大小： | 0K |
| 描述： | IC AMP DIFF 8SOIC |
| 产品培训模块： | Current Sense Amplifiers Top Five Instrumentation Amplifier Problems |
| 标准包装： | 98 |
| 放大器类型： | 差分 |
| 电路数： | 1 |
| 转换速率： | 0.5 V/µs |
| -3db带宽： | 100kHz |
| 电压 - 输入偏移： | 2000µV |
| 电流 - 电源： | 2mA |
| 电压 - 电源，单路/双路(±)： | 4.5 V ~ 5.5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SO |
| 包装： | 管件 |
| 产品目录页面： | 765 (CN2011-ZH PDF) |
Data Sheet
AD8206
Rev. B | Page 9 of 16
THEORY OF OPERATION
The AD8206 is a single-supply difference amplifier that uses
a unique architecture to accurately amplify small differential
current shunt voltages in the presence of rapidly changing
common-mode voltage. It is offered in an 8-lead SOIC package.
In typical applications, the AD8206 is used to measure current
by amplifying the voltage across a current shunt placed across
the inputs.
The gain of the AD8206 is 20 V/V, with an accuracy of 1.2%.
This accuracy is guaranteed over the operating temperature
range of 40°C to +125°C. Note, however, that the WH grade
version of the AD8206 is specified for operation from 40°C
to +150°C, with the same accuracy of 1.2%.
The AD8206 operates with a single supply from 4.5 V to
10 V (absolute maximum = 12.5 V). The supply current is
less than 2 mA.
High accuracy trimming of the internal resistors allows the
AD8206 to have a typical common-mode rejection ratio better
than 80 dB from dc to 20 kHz. The minimum common-mode
rejection ratio over the operating temperature is 76 dB.
The output offset can be adjusted from 0.08 V to 4.7 V
(VS = 5 V) for unidirectional and bidirectional operation.
The AD8206 consists of two amplifiers (A1 and A2), a resistor
network, a small voltage reference, and a bias circuit. See Figure 16
for a simplified schematic diagram (bias circuit not shown).
The set of input attenuators preceding A1 consist of RA, RB, and
RC, which reduce the common-mode voltage to match the input
voltage range of A1. The two attenuators form a balanced bridge
network. When the bridge is balanced, the differential voltage
created by a common-mode voltage is 0 V at the inputs of A1.
The input attenuation ratio is 1/16.7. The combined series
resistance of RA, RB, and RC is approximately 200 k ± 20%.
By attenuating the voltages at Pin 1 and Pin 8, the A1 amplifier
inputs are held within the power supply range, even if Pin 1
and Pin 8 exceed the supply or fall below common (ground). A
reference voltage of 250 mV biases the attenuator above ground.
This allows the amplifier to operate in the presence of negative
common-mode voltages.
The input network also attenuates normal (differential) mode
voltages. A1 amplifies the attenuated signal by 26. The input
and output of this amplifier are differential to maximize the
ac common-mode rejection.
A2 converts the differential voltage from A1 into a single-ended
signal and provides further amplification. The gain of this
second stage is 12.86.
The reference inputs, VREF1 and VREF2, are tied through resistors
to the positive input of A2, which allows the output offset to be
adjusted anywhere in the output operating range. The gain is
1 V/V from the reference pins to the output when the reference
pins are used in parallel. The gain is 0.5 V/V when they are used
to divide the supply.
The ratios of Resistors RA, RB, RC, RD, and RF are trimmed to a
high level of precision to allow the common-mode rejection
ratio to exceed 80 dB. This is accomplished by laser trimming
the resistor ratio matching to better than 0.01%.
The total gain of 20 is made up of the input attenuation of
1/16.7 multiplied by the first stage gain of 26 and the second
stage gain of 12.86.
The output stage is a Class A with a PNP pull-up transistor and
a 300 A current sink pull-down.
04953-013
AD8206
+IN
–IN
250mV
GND
A1
A2
RA
RB
RF
RD
RE
RF
RC
VOUT
RREF
VREF1
VREF2
Figure 16. Simplified Schematic
相关PDF资料 |
PDF描述 |
|---|---|
| OP27GSZ | IC OPAMP GP 8MHZ LN PREC 8SOIC |
| AD8027ARZ | IC OPAMP R-R LDIST LN LP 8SOIC |
| AD8203YRMZ | IC AMP DIFF 60KHZ 8MSOP |
| KD1245PFS2 H | FAN 12VDC 45X10MM 1.2W 7.1CFM |
| KD1205PFB2 H | FAN 12VDC 50X10.5MM 1.2W 9.5CFM |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD8206YRZ-REEL | 功能描述:IC AMP DIFF 8SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:2,500 系列:- 放大器类型:通用 电路数:1 输出类型:满摆幅 转换速率:0.11 V/µs 增益带宽积:350kHz -3db带宽:- 电流 - 输入偏压:4nA 电压 - 输入偏移:20µV 电流 - 电源:260µA 电流 - 输出 / 通道:20mA 电压 - 电源，单路/双路(±):2.7 V ~ 36 V，±1.35 V ~ 18 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SO 包装:带卷 (TR) |
| AD8206YRZ-REEL7 | 功能描述:IC AMP DIFF 8SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 产品培训模块:Differential Circuit Design Techniques for Communication Applications 标准包装:1 系列:- 放大器类型:RF/IF 差分 电路数:1 输出类型:差分 转换速率:9800 V/µs 增益带宽积:- -3db带宽:2.9GHz 电流 - 输入偏压:3µA 电压 - 输入偏移:- 电流 - 电源:40mA 电流 - 输出 / 通道:- 电压 - 电源，单路/双路(±):3 V ~ 3.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-VQFN 裸露焊盘，CSP 供应商设备封装:16-LFCSP-VQ 包装:剪切带 (CT) 产品目录页面:551 (CN2011-ZH PDF) 其它名称:ADL5561ACPZ-R7CT |
| AD8207 | 制造商:AD 制造商全称:Analog Devices 功能描述:Zero-Drift, High Voltage, Bidirectional Difference Amplifier |
| AD8207WBRZ | 功能描述:IC AMP 65V DIFF BIDIRECT 8SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:1 系列:- 放大器类型:通用 电路数:4 输出类型:满摆幅 转换速率:0.028 V/µs 增益带宽积:105kHz -3db带宽:- 电流 - 输入偏压:3nA 电压 - 输入偏移:100µV 电流 - 电源:3.3µA 电流 - 输出 / 通道:12mA 电压 - 电源，单路/双路(±):2.7 V ~ 12 V，±1.35 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:14-TSSOP 包装:剪切带 (CT) 其它名称:OP481GRUZ-REELCT |
| AD8207WBRZ-R7 | 功能描述:IC AMP 65V DIFF BIDIRECT 8SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 放大器类型:电流检测 电路数:1 输出类型:- 转换速率:- 增益带宽积:125kHz -3db带宽:- 电流 - 输入偏压:- 电压 - 输入偏移:100µV 电流 - 电源:1.1µA 电流 - 输出 / 通道:- 电压 - 电源，单路/双路(±):- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:4-WFBGA，CSPBGA 供应商设备封装:4-UCSP（2x2） 包装:剪切带 (CT) 其它名称:MAX9634WERS+TCT |
发布紧急采购，3分钟左右您将得到回复。