- 您现在的位置：买卖IC网 > PDF目录22244 > AD8210YRZ-REEL7 (Analog Devices Inc)IC CURRENT MONITOR 0.5% 8SOIC PDF资料下载
参数资料
| 型号： | AD8210YRZ-REEL7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 11/16页 |
| 文件大小： | 322K |
| 描述： | IC CURRENT MONITOR 0.5% 8SOIC |
| 设计资源： | High Voltage, High Precision Current Sensing with Output Level Shifting Using AD8210 and AD8274 (CN0116) |
| 标准包装： | 1,000 |
| 功能： | 电流监控器 |
| 检测方法： | 高/低端 |
| 精确度： | ±0.5% |
| 输入电压： | -2 V ~ 65 V |
| 电流 - 输出： | 5mA |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SO |
| 包装： | 带卷 (TR) |
Data Sheet
AD8210
Rev. D | Page 11 of 16
MODES OF OPERATION
The AD8210 can be adjusted for unidirectional or bidirectional
operation.
UNIDIRECTIONAL OPERATION
Unidirectional operation allows the AD8210 to measure
currents through a resistive shunt in one direction. The basic
modes for unidirectional operation are ground referenced
output mode and V+ referenced output mode.
In unidirectional operation, the output can be set at the negative
rail (near ground) or at the positive rail (near V+) when the
differential input is 0 V. The output moves to the opposite rail
when a correct polarity differential input voltage is applied. In
this case, full scale is approximately 250 mV. The required
polarity of the differential input depends on the output voltage
setting. If the output is set at ground, the polarity needs to be
positive to move the output up (see Table 5). If the output is set
at the positive rail, the input polarity needs to be negative to
move the output down (see Table 6).
Ground Referenced Output
When using the AD8210 in this mode, both reference inputs
are tied to ground, which causes the output to sit at the negative
rail when the differential input voltage is zero (see Figure 27
and Table 4).
AD8210
OUTPUT
G = +20
R
S
+IN
IN
V
S
V
REF
1
V
REF
2
GND
0.1礔
Figure 27. Ground Referenced Output
Table 4. V+ = 5 V
VIN (Referred to IN)
VO
0 V
0.05 V
250 mV
4.9 V
V+ Referenced Output
This mode is set when both reference pins are tied to the
positive supply. It is typically used when the diagnostic scheme
requires detection of the amplifier and wiring before power is
applied to the load (see Figure 28 and Table 5).
AD8210
OUTPUT
G = +20
R
S
+IN
IN
V
S
V
REF
1
V
REF
2
GND
0.1礔
Figure 28. V+ Referenced Output
Table 5. V+ = 5 V
V
IN
(Referred to IN)
V
O
0 V
4.9 V
250 mV
0.05 V
BIDIRECTIONAL OPERATION
Bidirectional operation allows the AD8210 to measure currents
through a resistive shunt in two directions. The output offset
can be set anywhere within the output range. Typically, it is set
at half scale for equal measurement range in both directions. In
some cases, however, it is set at a voltage other than half scale
when the bidirectional current is nonsymmetrical.
Table 6. V+ = 5 V, VO = 2.5 V with VIN = 0 V
VIN (Referred to IN)
VO
+125 mV
4.9 V
125 mV
0.05 V
Adjusting the output can also be accomplished by applying
voltage(s) to the reference inputs.
相关PDF资料 |
PDF描述 |
|---|---|
| AISC-1008-R10G-T | INDUCTOR 100NH 650MA 2% SMD |
| AISC-1008-R082G-T | INDUCTOR 82NH 1000MA 2% SMD |
| C0603C0G1H130J | CAP CER 13PF 50V 5% NP0 0201 |
| LT3092IDD#TRPBF | IC PROG CURRENT SOURCE 8DFN |
| AISC-1008-R047G-T | INDUCTOR 47NH 1000MA 2% SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD8211 | 制造商:AD 制造商全称:Analog Devices 功能描述:High Voltage Current Shunt Monitor |
| AD8211WYRJZ-R7 | 制造商:Analog Devices 功能描述:CURRENT SHUNT MONITOR 5PIN SOT-23 - Tape and Reel |
| AD8211WYRJZ-RL | 制造商:Analog Devices 功能描述: |
| AD8211YRJ | 制造商:Analog Devices 功能描述:CURRENT SHUNT MONITOR 4.5V/US 5SOT23 制造商:Analog Devices 功能描述:CURRENT SHUNT MONITOR, 4.5V/US, 5SOT23 制造商:Analog Devices 功能描述:CURRENT SHUNT MONITOR, 4.5V/US, 5SOT23, No. of Amplifiers:1, Input Offset Voltag 制造商:Analog Devices 功能描述:CURRENT SHUNT MONITOR, 4.5V/US, 5SOT23, No. of Amplifiers:1, Input Offset Voltage:1mV, Amplifier Case Style:SOT-23, No. of Pins:5, Bandwidth:500kHz, CMRR:220dB, Supply Voltage Min:4.5V, Supply Voltage Max:5.5V, Supply Current:1.2mA, , RoHS Compliant: Yes |
| AD8211YRJZ-R2 | 功能描述:IC CURRENT MONITOR 0.25% SOT23-5 RoHS:是 类别:集成电路 (IC) >> PMIC - 稳流/电流管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 功能:电流开关 检测方法:- 精确度:±10% 输入电压:1.7 V ~ 5.5 V 电流 - 输出:600mA 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-UFQFN 供应商设备封装:10-UTQFN（1.4x1.8） 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。