参数资料
| 型号： | AD8216WYRZ-RL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 3/16页 |
| 文件大小： | 0K |
| 描述： | IC AMP 65V DIFF BIDIRECT 8SOIC |
| 标准包装： | 2,500 |
| 放大器类型： | 差分 |
| 电路数： | 1 |
| 转换速率： | 15 V/µs |
| -3db带宽： | 3MHz |
| 电压 - 输入偏移： | 500µV |
| 电流 - 电源： | 1mA |
| 电压 - 电源，单路/双路(±)： | 4.5 V ~ 5.5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SO |
| 包装： | 带卷 (TR) |
Data Sheet
AD8216
Rev. B | Page 11 of 16
OUTPUT OFFSET ADJUSTMENT
The output of the AD8216 can be adjusted for unidirectional or
bidirectional operation.
UNIDIRECTIONAL OPERATION
Unidirectional operation allows the AD8216 to measure currents
through a resistive shunt in one direction. The basic modes for
unidirectional operation are ground referenced output mode
and V+ referenced output mode.
For unidirectional operation, the output can be set at the
negative rail (near ground) or at the positive rail (near V+)
when the differential input is 0 V. The output moves to the
opposite rail when a correct polarity differential input voltage is
applied. In this case, full scale is approximately 1.6 V. The required
polarity of the differential input depends on the output voltage
setting. If the output is set at the positive rail, the input polarity
needs to be negative to move the output down. If the output is
set at ground, the polarity is positive to move the output up.
GROUND REFERENCED OUTPUT
When using the AD8216 in this mode, both referenced inputs are
tied to ground, which causes the output to sit at the negative rail
when there are zero differential volts at the input (see Figure 24).
AD8216
+IN
–IN
NC
NC = NO CONNECT
GND
V+
OUT
VREF1
VREF2
07
06
2-
02
9
Figure 24. Ground Referenced Output
Table 4. V+ = 5 V
VIN (Referred to IN)
VOUT
0 V
0.1 V
1.6 V
4.8 V
V+ REFERENCED OUTPUT
The V+ referenced output mode is set when both reference
pins are tied to the positive supply. It is typically used when the
diagnostic scheme requires detection of the amplifier and the
wiring before power is applied to the load (see Figure 25).
AD8216
+IN
–IN
NC
NC = NO CONNECT
GND
V+
OUT
VREF1
VREF2
0
70
62
-030
Figure 25. V+ Referenced Output
Table 5. V+ = 5 V
VIN (Referred to IN)
VOUT
0 V
4.9 V
1.6 V
0.1 V
BIDIRECTIONAL OPERATION
Bidirectional operation allows the AD8216 to measure currents
through a resistive shunt in two directions.
In this case, the output is set anywhere within the output range.
Typically, it is set at half scale for equal range in both directions.
In some cases, however, it is set at a voltage other than half scale
when the bidirectional current is nonsymmetrical.
Table 6. V+ = 5 V, VOUT = 2.5 V with VIN = 0 V
VIN (Referred to IN)
VOUT
+800 mV
4.9 V
800 mV
0.1V
Adjusting the output is accomplished by applying voltage(s) to
the referenced inputs.
VREF1 and VREF2 are tied to internal resistors that connect to an
internal offset node. There is no operational difference between
the pins.
相关PDF资料 |
PDF描述 |
|---|---|
| PPPC082LJBN-RC | CONN FEMALE 16POSDL .1" R/A GOLD |
| ADA4841-1YRJZ-RL | IC OPAMP VF R-R LP LN SOT23-6 |
| LPPB101NFSC-RC | CONN HEADER .050" 10POS SMD GOLD |
| NPPN062GFNS-RC | CONN RECEPT 2MM DUAL SMD 12POS |
| ADA4051-1AKSZ-R2 | IC OPAMP RRIO ZERO DRIFT SC70-5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD8216YRZ | 功能描述:IC AMP DIFF 8SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:1 系列:- 放大器类型:通用 电路数:4 输出类型:满摆幅 转换速率:0.028 V/µs 增益带宽积:105kHz -3db带宽:- 电流 - 输入偏压:3nA 电压 - 输入偏移:100µV 电流 - 电源:3.3µA 电流 - 输出 / 通道:12mA 电压 - 电源，单路/双路(±):2.7 V ~ 12 V，±1.35 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:14-TSSOP 包装:剪切带 (CT) 其它名称:OP481GRUZ-REELCT |
| AD8216YRZ | 制造商:Analog Devices 功能描述:IC DIFFERENTIAL AMP 3MHZ 15V/S SOIC8 |
| AD8216YRZ-R7 | 功能描述:IC AMP DIFF 8SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 产品培训模块:Differential Circuit Design Techniques for Communication Applications 标准包装:1 系列:- 放大器类型:RF/IF 差分 电路数:1 输出类型:差分 转换速率:9800 V/µs 增益带宽积:- -3db带宽:2.9GHz 电流 - 输入偏压:3µA 电压 - 输入偏移:- 电流 - 电源:40mA 电流 - 输出 / 通道:- 电压 - 电源，单路/双路(±):3 V ~ 3.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-VQFN 裸露焊盘，CSP 供应商设备封装:16-LFCSP-VQ 包装:剪切带 (CT) 产品目录页面:551 (CN2011-ZH PDF) 其它名称:ADL5561ACPZ-R7CT |
| AD8216YRZ-RL | 功能描述:IC AMP DIFF 8SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:- 放大器类型:通用 电路数:2 输出类型:满摆幅 转换速率:1.8 V/µs 增益带宽积:6.5MHz -3db带宽:4.5MHz 电流 - 输入偏压:5nA 电压 - 输入偏移:100µV 电流 - 电源:65µA 电流 - 输出 / 通道:35mA 电压 - 电源，单路/双路(±):1.8 V ~ 5.25 V，±0.9 V ~ 2.625 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| AD8217 | 制造商:AD 制造商全称:Analog Devices 功能描述:High Resolution, Zero-Drift Current Shunt Monitor |
发布紧急采购，3分钟左右您将得到回复。