参数资料
型号: AD8225
厂商: Analog Devices, Inc.
元件分类: 运动控制电子
英文描述: Precision Gain of 5 Instrumentation Amplifier
中文描述: 5精密增益仪表放大器
文件页数: 13/16页
文件大小: 372K
代理商: AD8225
REV. A
AD8225
–13–
In the classical three op amp in amp topology shown in Figure 8,
gain is developed differentially between the two input amplifiers
A1 and A2, sacrificing CMV (common-mode voltage) range.
The gain of the in amp is typically 10 or less, and an additional
gain stage increases the overall gain to approximately 1000.
Gain developed in the input stage results in a trade-off in common-
mode voltage range, constraining the ability of the amplifier to
tolerate high dc electrode errors. Although the AD8225 is also
a three amplifier design, its gain of 5 is developed at the
output
amplifier, improving the CMV range at the input. Using
±
5 V
supplies, the CMV range of the AD8225 is from
3.4 V to
+4 V, compared to
3.1 V to +3.8 V, a 7% improvement in
input headroom over conventional in amps with the same gain.
G = 5
AD8225
19.6k
301
100
OP77
G = 200
G = 5
AD8225
19.6k
301
100
OP77
G = 200
G = 5
AD8225
19.6k
301
100
OP77
G = 200
Figure 9. EKG Monitor Front End
Figure 9 illustrates how an AD8225 may be used in an EKG
front end. In a low cost system, the AD8225 can be connected to
the patient. If buffers are required, the AD8225 can replace the
expensive precision resistor network and op amp.
Figure 10 shows test waveforms observed from the circuit of
Figure 9.
CH 1 = 2V, CH 2 = 2V, CH 3 = 2V, H = 200ms
RA-LA 1
LA-LL 2
RA-LL 3
Figure 10. EKG Waveform Using Circuit of Figure 9
Benefits of Fast Slew Rates
At 5 V/
μ
s, the slew rate of the AD8225 is as fast as many op amp
circuits. This is an advantage in systems applications using multiple
sensors. For example, an analog multiplexer (see Figure 11) may
be used to select pairs of leads connected to several sensors. If
the AD8225 drives an ADC, the acquisition time is constrained
by the ability of the in amp to settle to a stable level after a new
set of leads is selected. Fast slew rates contribute greatly to
this function, especially if the difference in input levels is large.
AD8225
S1A
S1B
S2A
S2B
S3A
S3B
S4A
S4B
0.2V, 2V
ADG409
1
4
DA
DB
REF
Figure 11. Connection to an ADG409 Analog MUX
Figure 12 illustrates the response of an AD8225 connected to
an ADG409 analog multiplexer in the circuit shown in Figure 11
at two signal levels. Two of the four MUX inputs are connected
to test dc levels. The remaining two are at ground potential so
that the output slews as the inputs A0 and A1 are addressed. As
can be seen, the output response settles well within 4
μ
s of the
applied level.
CH 1 = 200mV, CH 2 = 2V, H = 500ns
LARGE SIGNAL
(2V/DIV)
SMALL SIGNAL
(200mV/DIV)
INPUT
SIGNAL
TRAN-
SITION
Figure 12. Slew Responses After MUX Selection
相关PDF资料
PDF描述
AD8225-EVAL Precision Gain of 5 Instrumentation Amplifier
AD8225AR Precision Gain of 5 Instrumentation Amplifier
AD8225AR-REEL7 Precision Gain of 5 Instrumentation Amplifier
AD823AN Dual, 16 MHz, Rail-to-Rail FET Input Amplifier
AD823AR Dual, 16 MHz, Rail-to-Rail FET Input Amplifier
相关代理商/技术参数
参数描述
AD8225AR 制造商:Analog Devices 功能描述:SP Amp INSTR Amp Single 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Analog Devices 功能描述:INSTRUMENT AMPLIFIER IC NUMBER OF CIRCUI
AD8225AR-REEL 制造商:Analog Devices 功能描述:SP Amp INSTR Amp Single ±18V/36V 8-Pin SOIC N T/R
AD8225AR-REEL7 制造商:Analog Devices 功能描述:SP Amp INSTR Amp Single
AD8225ARZ 功能描述:IC AMP INST PREC LP LDRIFT 8SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:2,500 系列:- 放大器类型:通用 电路数:4 输出类型:- 转换速率:0.6 V/µs 增益带宽积:1MHz -3db带宽:- 电流 - 输入偏压:45nA 电压 - 输入偏移:2000µV 电流 - 电源:1.4mA 电流 - 输出 / 通道:40mA 电压 - 电源,单路/双路(±):3 V ~ 32 V,±1.5 V ~ 16 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:14-TSSOP(0.173",4.40mm 宽) 供应商设备封装:14-TSSOP 包装:带卷 (TR) 其它名称:LM324ADTBR2G-NDLM324ADTBR2GOSTR
AD8225ARZ-R7 功能描述:IC AMP INST PREC LP LDRIFT 8SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:73 系列:Over-The-Top® 放大器类型:通用 电路数:4 输出类型:满摆幅 转换速率:0.07 V/µs 增益带宽积:200kHz -3db带宽:- 电流 - 输入偏压:1nA 电压 - 输入偏移:285µV 电流 - 电源:50µA 电流 - 输出 / 通道:25mA 电压 - 电源,单路/双路(±):2 V ~ 44 V,±1 V ~ 22 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-WFDFN 裸露焊盘 供应商设备封装:16-DFN-EP(5x3) 包装:管件