- 您现在的位置：买卖IC网 > PDF目录5884 > AD823AR-REEL7 (Analog Devices Inc)IC OPAMP JFET R-R DUAL LN 8SOIC PDF资料下载
参数资料
| 型号： | AD823AR-REEL7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 7/20页 |
| 文件大小： | 0K |
| 描述： | IC OPAMP JFET R-R DUAL LN 8SOIC |
| 标准包装： | 750 |
| 放大器类型： | J-FET |
| 电路数： | 2 |
| 输出类型： | 满摆幅 |
| 转换速率： | 25 V/µs |
| -3db带宽： | 16MHz |
| 电流 - 输入偏压： | 5pA |
| 电压 - 输入偏移： | 700µV |
| 电流 - 电源： | 7mA |
| 电流 - 输出 / 通道： | 17mA |
| 电压 - 电源，单路/双路(±)： | 3 V ~ 36 V，±1.5 V ~ 18 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SO |
| 包装： | 带卷 (TR) |
| 其它名称： | AD823AR-REEL7TR |
Data Sheet
AD823
Rev. E | Page 15 of 20
APPLICATION NOTES
INPUT CHARACTERISTICS
In the AD823, N-Channel JFETs are used to provide a low offset,
low noise, high impedance input stage. Minimum input common-
mode voltage extends from 0.2 V below VS to 1 V < +VS. Driving
the input voltage closer to the positive rail causes a loss of amplifier
bandwidth and increased common-mode voltage error.
The AD823 does not exhibit phase reversal for input voltages up
to and including +VS. Figure 38 shows the response of an AD823
voltage follower to a 0 V to 5 V (+VS) square wave input. The
input and output are superimposed. The output polarity tracks
the input polarity up to +VS, with no phase reversal. The reduced
bandwidth above a 4 V input causes the rounding of the output
wave form. For input voltages greater than +VS, a resistor in
series with the AD823’s noninverting input prevents phase
reversal, at the expense of greater input voltage noise. This is
illustrated in Figure 39.
GND
100
0%
1V
2s
1V
90
00901-
038
10
Figure 38. AD823 Input Response: RP = 0, VIN = 0 to +VS
+VS
GND
5V
VIN
RP
VOUT
AD823
1V
10 s
1V
00901-
039
90
100
10
0%
Figure 39. AD823 Input Response:
VIN = 0 to +VS + 200 mV, VOUT = 0 to +VS, RP = 49.9 k
Because the input stage uses N-Channel JFETs, input current
during normal operation is negative; the current flows out from
the input terminals. If the input voltage is driven more positive
than +VS 0.4 V, the input current reverses direction as internal
device junctions become forward biased. This is illustrated in
A current limiting resistor should be used in series with the
input of the AD823 if there is a possibility of the input voltage
exceeding the positive supply by more than 300 mV, or if an
input voltage is applied to the AD823 when ±VS = 0. The
amplifier becomes damaged if left in that condition for more
than 10 seconds. A 1 k resistor allows the amplifier to
withstand up to 10 V of continuous overvoltage and increases
the input voltage noise by a negligible amount.
Input voltages less than VS are a completely different story.
The amplifier can safely withstand input voltages 20 V below
VS as long as the total voltage from the positive supply to the
input terminal is less than 36 V. In addition, the input stage
typically maintains picoamp level input currents across that
input voltage range.
The AD823 is designed for 16 nV/√Hz wideband input voltage
noise and maintains low noise performance to low frequencies
(see Figure 16). This noise performance, along with the AD823’s
low input current and current noise, means that the AD823
contributes negligible noise for applications with source
resistances greater than 10 k and signal bandwidths greater
than 1 kHz.
OUTPUT CHARACTERISTICS
The AD823’s unique bipolar rail-to-rail output stage swings
within 25 mV of the supplies with no external resistive load.
The AD823’s approximate output saturation resistance is 25
sourcing and sinking. This can be used to estimate the output
saturation voltage when driving heavier current loads. For
instance, when driving 5 mA, the saturation voltage to the rails
is approximately 125 mV.
If the AD823’s output is driven hard against the output
saturation voltage, it recovers within 250 ns of the input
returning to the amplifier’s linear operating region.
A/D Driver
The rail-to-rail output of the AD823 makes it useful as an A/D
driver in a single-supply system. Because it is a dual op amp, it
can be used to drive both the analog input of the A/D as well as
its reference input. The high impedance FET input of the
AD823 is well suited for minimal loading of high output
impedance devices.
相关PDF资料 |
PDF描述 |
|---|---|
| FTS-130-01-L-D | CONN HEADER 60POS DUAL .05" T/H |
| 929667-01-23-I | CONN HEADER 46POS DUAL .100 R/A |
| SL1024B090RF | GAS TUBE GDT 10KA 90V RAD +FS |
| TSW-139-17-G-D | CONN HEADER 78POS .100" DL GOLD |
| AD8131ARM | IC AMP DIFF LDIST 60MA 8MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD823ARZ | 功能描述:IC OPAMP JFET R-R DUAL LN 8SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:2,500 系列:- 放大器类型:通用 电路数:4 输出类型:- 转换速率:0.6 V/µs 增益带宽积:1MHz -3db带宽:- 电流 - 输入偏压:45nA 电压 - 输入偏移:2000µV 电流 - 电源:1.4mA 电流 - 输出 / 通道:40mA 电压 - 电源，单路/双路(±):3 V ~ 32 V，±1.5 V ~ 16 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:14-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:14-TSSOP 包装:带卷 (TR) 其它名称:LM324ADTBR2G-NDLM324ADTBR2GOSTR |
| AD823ARZ | 制造商:Analog Devices 功能描述:Operational Amplifier (Op-Amp) IC |
| AD823ARZ-R7 | 功能描述:IC OPAMP JFET R-R DUAL LN 8SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:1 系列:- 放大器类型:通用 电路数:4 输出类型:满摆幅 转换速率:0.028 V/µs 增益带宽积:105kHz -3db带宽:- 电流 - 输入偏压:3nA 电压 - 输入偏移:100µV 电流 - 电源:3.3µA 电流 - 输出 / 通道:12mA 电压 - 电源，单路/双路(±):2.7 V ~ 12 V，±1.35 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:14-TSSOP 包装:剪切带 (CT) 其它名称:OP481GRUZ-REELCT |
| AD823ARZ-RL | 功能描述:IC OPAMP JFET R-R DUAL LN 8SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:1 系列:- 放大器类型:通用 电路数:4 输出类型:满摆幅 转换速率:0.028 V/µs 增益带宽积:105kHz -3db带宽:- 电流 - 输入偏压:3nA 电压 - 输入偏移:100µV 电流 - 电源:3.3µA 电流 - 输出 / 通道:12mA 电压 - 电源，单路/双路(±):2.7 V ~ 12 V，±1.35 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:14-TSSOP 包装:剪切带 (CT) 其它名称:OP481GRUZ-REELCT |
| AD824 | 制造商:AD 制造商全称:Analog Devices 功能描述:Single Supply, Rail-to-Rail Low Power, FET-Input Op Amp |
发布紧急采购，3分钟左右您将得到回复。