- 您现在的位置：买卖IC网 > Datasheet目录307 > AD8240YRMZ (Analog Devices Inc)IC LED DRIVER PWM CONTROL 8-MSOP Datasheet资料下载
参数资料
| 型号： | AD8240YRMZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 8/12页 |
| 文件大小： | 0K |
| 描述： | IC LED DRIVER PWM CONTROL 8-MSOP |
| 标准包装： | 50 |
| 恒定电流： | 是 |
| 拓扑： | 线性，PWM |
| 输出数： | 1 |
| 内部驱动器： | 无 |
| 类型 - 主要： | 车载 |
| 频率： | 500Hz |
| 电源电压： | 9 V ~ 27 V |
| 输出电压： | 12V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-MSOP |
| 包装： | 管件 |
| 工作温度： | -40°C ~ 125°C |
| 产品目录页面： | 791 (CN2011-ZH PDF) |
AD8240
ADVANTAGES OF DRIVING LED LAMPS WITH CONSTANT VOLTAGE
The advantages of driving LED lamps with constant voltage are
DRIVING AUTOMOTIVE LEDS
?
?
?
Low system cost
Accurate monitoring
Proven strategy
There are two different architectures for driving LEDs in
left/right/center brake lamps, running lamps, and turn signals.
Constant Current
The most common method for driving LEDs is with a constant
BACKGROUND
A great variety of LED lamps are being used in automotive
applications. The most popular application is center brake
lamps. Currently, many manufacturers are developing
technology to use LEDs for left/right brake lamps, running
lamps, and turn signals. There are also plans to use high power
LEDs for forward lighting fog lamps and low beams.
There are two fundamental types of LEDs used in these applica-
tions. The first is the low power bright LED. The second type is
the high power, extremely bright LED in the 1 W to 10 W range.
While the following information can be applied to applications
using the high power LED, or incandescent lamps, the constant
voltage method is designed for applications typically using the
low power bright LEDs. This type of LED is used in arrays that
form LED lamps.
MONITORING THE LEDS
In addition to driving the LED lamp, the electronics in the
control module must include a method for monitoring partial
LED failure in the lamp. Certain factors, such as overdriving
and mechanical stress, can cause LED failures.
Auto manufacturers are using LED lamps as a way to differen-
tiate themselves and give a car a unique appearance. Several
failed LEDs in the lamp would ruin the aesthetics of the lamp.
As a result, manufacturers are demanding the ability to monitor
the LED lamps for partial failure.
In addition to monitoring the LEDs for aesthetic reasons,
monitoring must also be included as a result of automotive
regulations. These regulations specify the minimum light
output of external lamps. For example, if half of the LEDs in
a particular lamp failed, the lamp would still operate, but the
light output would be insufficient to meet automotive
regulations for brightness. This concern is not an issue for
incandescent bulbs, because they are either completely on or
completely off. The ability of the LED lamp to provide some
light output in the case of partial outage, however, allows for an
extra degree of safety over incandescent lamps. Additionally,
current. This current can be supplied from a constant current
source or from a constant voltage source in series with a ballast
resistor. Driving LEDs without some form of ballast carries
some risk of premature LED failure due to thermal runaway in
high temperature ambient conditions.
For example, in the simplest application, the center brake lamp
is driven from a relatively constant voltage with brightness
controlled by a series ballast resistor. This simple driving
method has been used in a wide variety of automotive platforms
for some time. With this method, the LEDs and ballast resistors
are preselected for brightness as part of the manufacturing
strategy.
When driving with a constant current source, LED driving
and monitoring cannot be done using two or fewer wires
(shared ground). Since the current is constant, it does not
change with partial LED failure. Instead, the current is divided
among the remaining functional LEDs, causing them to fail
prematurely at an unpredictable rate. Additionally, it is not
possible to detect partial failure by measuring the voltage
change. The voltage does not change by a detectable amount
because of the steep V/I curve exhibited by bright LEDs. When
using a constant current scheme, at least one additional wire
per lamp must be added to the harness to monitor partial or
total LED failure. Additionally, electronic modules must be
added to each lamp.
Constant Voltage
Driving LEDs with a constant voltage allows for easy, low cost
detection of partial failure, an advantage not available with a
constant-current architecture. This is because the current from
the voltage source changes in direct proportion to the number
of LEDs that have failed. This current can be measured with a
low cost shunt and an amplifier back at the body control
module. This detection scheme is implemented in the AD8240
LED driver/monitor through the use of a high-side, current-
sensing amplifier. The current is measured on the high side in
order to separate the current from those combined in the
chassis ground return or shared-wire ground return.
there are automotive regulations requiring the monitoring of
the turn signals regardless of the type of light source.
Rev. 0 | Page 8 of 12
相关PDF资料 |
PDF描述 |
|---|---|
| ADD5203ACPZ-RL | IC LED DRVR WHITE BCKLGT 28LFCSP |
| ADD5205ACPZ-RL | IC LED DVR WHITE BCKLGT 12LFCSP |
| ADE5566ASTZF62-RL | IC ENERGY METERING 1PHASE 64LQFP |
| ADE7156ASTZF16 | IC ENERGY METER 64-LQFP |
| ADE7156ASTZF8-RL | IC ENERGY METER 64-LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD8240YRMZ-R7 | 功能描述:IC LED DRIVER PWM CONTROL 8-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND |
| AD8240YRMZ-RL | 功能描述:IC LED DRIVER PWM CONTROL 8-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND |
| AD8244 | 制造商:AD 制造商全称:Analog Devices 功能描述:Single-Supply, Low Power, Precision FET Input Quad Buffer |
| AD8244ARMZ | 制造商:Analog Devices 功能描述:JFET QUAD BUFFER AFE - Rail/Tube 制造商:Analog Devices 功能描述:IC BUFFER QUAD FET-INPUT 10MSOP 制造商:Analog Devices 功能描述:Operational Amplifiers - Op Amps JFET Quad Buffer AFE Sigma Delta ADC |
| AD8244ARMZ-R7 | 制造商:Analog Devices 功能描述:JFET QUAD BUFFER AFE - Tape and Reel |
发布紧急采购，3分钟左右您将得到回复。