- 您现在的位置：买卖IC网 > PDF目录373941 > AD824BN (ANALOG DEVICES INC) Single Supply, Rail-to-Rail Low Power, FET-Input Op Amp PDF资料下载
参数资料
| 型号： | AD824BN |
| 厂商： | ANALOG DEVICES INC |
| 元件分类： | 运动控制电子 |
| 英文描述： | Single Supply, Rail-to-Rail Low Power, FET-Input Op Amp |
| 中文描述： | QUAD OP-AMP, 2500 uV OFFSET-MAX, 2 MHz BAND WIDTH, PDIP14 |
| 封装： | PLASTIC, DIP-14 |
| 文件页数： | 14/16页 |
| 文件大小： | 551K |
| 代理商： | AD824BN |
AD824
–14–
REV. A
A design consideration in sample-and-hold circuits is voltage
droop at the output caused by op amp bias and switch leakage
currents. By choosing a JFET op amp and a low leakage CMOS
switch, this design minimizes droop rate error to better than
0.1
μ
V/
μ
s in this circuit. Higher values of C
H
will yield a lower
droop rate. For best performance, C
H
and C2 should be poly-
styrene, polypropylene or Teflon capacitors. These types of
capacitors exhibit low leakage and low dielectric absorption. Addi-
tionally, 1% metal film resistors were used throughout the design.
In the sample mode, SW1 and SW4 are closed, and the output
is V
OUT
= –V
IN
. The purpose of SW4, which operates in paral-
lel with SW1, is to reduce the pedestal, or hold step, error by
injecting the same amount of charge into the noninverting input
of A3 that SW1 injects into the inverting input of A3. This cre-
ates a common-mode voltage across the inputs of A3 and is then
rejected by the CMR of A3; otherwise, the charge injection from
SW1 would create a differential voltage step error that would
appear at V
OUT
. The pedestal error for this circuit is less than 2
mV over the entire 0 V to 3.3 V/5 V signal range. Another
method of reducing pedestal error is to reduce the pulse ampli-
tude applied to the control pins. In order to control the
ADG513, only 2.4 V are required for the “ON” state and 0.8V
for the “OFF” state. If possible, use an input control signal
whose amplitude ranges from 0.8 V to 2.4 V instead of a full
range 0 V to 3.3 V/5 V for minimum pedestal error.
Other circuit features include an acquisition time of less than
3
μ
s to 1%; reducing C
H
and C2 will speed up the acquisition
time further, but an increased pedestal error will result. Settling
time is less than 300 ns to 1%, and the sample-mode signal BW
is 80 kHz.
The ADG513 was chosen for its ability to work with 3 V/5 V
supplies and for having normally-open and normally-closed pre-
cision CMOS switches on a dielectrically isolated process. SW2
is not required in this circuit; however, it was used in parallel
with SW3 to provide a lower R
ON
analog switch.
相关PDF资料 |
PDF描述 |
|---|---|
| AD824ACHIPS | Single Supply, Rail-to-Rail Low Power, FET-Input Op Amp |
| AD824AR-14 | VARISTOR 140V RMS 14MM RADIAL |
| AD824AR-14-3V | VARISTOR 14V RMS 14MM RADIAL |
| AD824AR-16 | VARISTOR 250V RMS 14MM RADIAL |
| AD824AR-3V | VARISTOR 35VRMS 14MM RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD825 | 制造商:AD 制造商全称:Analog Devices 功能描述:Low Cost, General-Purpose High Speed JFET Amplifier |
| AD825_04 | 制造商:AD 制造商全称:Analog Devices 功能描述:Low Cost, General-Purpose High Speed JFET Amplifier |
| AD8250 | 制造商:AD 制造商全称:Analog Devices 功能描述:Wide Supply Range, Micropower, |
| AD8250ARMZ | 功能描述:IC AMP INST ICMOS LDRIFT 10MSOP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:iCMOS® 标准包装:2,500 系列:- 放大器类型:通用 电路数:4 输出类型:- 转换速率:0.6 V/µs 增益带宽积:1MHz -3db带宽:- 电流 - 输入偏压:45nA 电压 - 输入偏移:2000µV 电流 - 电源:1.4mA 电流 - 输出 / 通道:40mA 电压 - 电源，单路/双路(±):3 V ~ 32 V，±1.5 V ~ 16 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:14-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:14-TSSOP 包装:带卷 (TR) 其它名称:LM324ADTBR2G-NDLM324ADTBR2GOSTR |
| AD8250ARMZ-R7 | 功能描述:IC AMP INST ICMOS LDRIFT 10MSOP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:iCMOS® 标准包装:2,500 系列:- 放大器类型:通用 电路数:4 输出类型:- 转换速率:0.6 V/µs 增益带宽积:1MHz -3db带宽:- 电流 - 输入偏压:45nA 电压 - 输入偏移:2000µV 电流 - 电源:1.4mA 电流 - 输出 / 通道:40mA 电压 - 电源，单路/双路(±):3 V ~ 32 V，±1.5 V ~ 16 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:14-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:14-TSSOP 包装:带卷 (TR) 其它名称:LM324ADTBR2G-NDLM324ADTBR2GOSTR |
发布紧急采购，3分钟左右您将得到回复。