参数资料
| 型号： | AD827JR-16 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 10/12页 |
| 文件大小： | 0K |
| 描述： | IC OPAMP GP 50MHZ DUAL LP 16SOIC |
| 标准包装： | 47 |
| 放大器类型： | 通用 |
| 电路数： | 2 |
| 转换速率： | 300 V/µs |
| 增益带宽积： | 50MHz |
| 电流 - 输入偏压： | 3.3µA |
| 电压 - 输入偏移： | 500µV |
| 电流 - 电源： | 10.5mA |
| 电流 - 输出 / 通道： | 32mA |
| 电压 - 电源，单路/双路(±)： | ±4.5 V ~ 18 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 16-SOIC W |
| 包装： | 管件 |
AD827
REV. C
–7–
VIDEO LINE DRIVER
The AD827 functions very well as a low cost, high speed line
driver for either terminated or unterminated cables. Figure 23
shows the AD827 driving a doubly terminated cable in a
follower configuration.
0.1 F
50
AD827
1/2
RBT
CC
+VS
VIN
VOUT
–VS
RT
500
50
50
500
Figure 23. A Video Line Driver
The termination resistor, RT, (when equal to the cable’s
characteristic impedance) minimizes reflections from the far end
of the cable. While operating from
±5 V supplies, the AD827
maintains a typical slew rate of 200 V/
s, which means it can
drive a
±1 V, 30 MHz signal into a terminated cable.
Table I. Video Line Driver Performance Summary
Over-
VIN*
VSUPPLY
CC
–3 dB BW
shoot
0 dB or
±500 mV Step ±15
20 pF
23 MHz
4%
0 dB or
±500 mV Step ±15
15 pF
21 MHz
0%
0 dB or
±500 mV Step ±15
0 pF
13 MHz
0%
0 dB or
±500 mV Step ±5
20 pF
18 MHz
2%
0 dB or
±500 mV Step ±5
15 pF
16 MHz
0%
0 dB or
±500 mV Step ±50 pF
11 MHz
0%
*–3 dB bandwidth numbers are for the 0 dBm signal input. Overshoot numbers
are the percent overshoot of the 1 V step input.
A back-termination resistor (RBT, also equal to the characteristic
impedance of the cable) may be placed between the AD827
output and the cable input, in order to damp any reflected
signals caused by a mismatch between RT and the cable’s
characteristic impedance. This will result in a flatter frequency
response, although this requires that the op amp supply
±2 V to
the output in order to achieve a
±1 V swing at resistor RT.
A HIGH SPEED THREE OP AMP INSTRUMENTATION
AMPLIFIER CIRCUIT
The instrumentation amplifier circuit shown in Figure 24 can
provide a range of gains. Table II details performance.
–
+
–
+
–
1
3
2
3
6
7
6
5
AD847
AD827
0.1
F
1k
2k
2k
1k
2k
0.1
F
0.1
F
2k
R
L
2 – 8pF
0.1
F
R
G
4
7
2k
8
4
TRIM FOR BEST
SETTLING TIME
1/2
3pF
CIRCUIT GAIN =
+ 1
G
R
2000
TRIM FOR
OPTIMUM
BANDWIDTH
7 – 15 pF
NOTE: PINOUT SHOWN IS FOR MINIDIP PACKAGE
–V
IN
+VS
–V
S
+V
IN
+V
S
–V
S
VOUT
Figure 24. A High Bandwidth Three Op Amp
Instrumentation Amplifier
Table II. Performance Specifications for the
Three Op Amp Instrumentation Amplifier
Small Signal
Bandwidth
Gain
RG
@ 1 V p-p Output
1
Open
16.1 MHz
22 k
14.7 MHz
10
226
4.9 MHz
100
20
660 kHz
相关PDF资料 |
PDF描述 |
|---|---|
| DF7-9P-3.96DSA | CONN HEADER 9POS 3.96MM VERT TIN |
| 69192-160 | BERGSTIK II DR STRAIGHT RET |
| DF7-8P-3.96DSA | CONN HEADER 8POS 3.96MM VERT TIN |
| LT1058ISW#TRPBF | IC PREC OP-AMP JFET QUAD 16SOIC |
| DF7-7P-3.96DSA | CONN HEADER 7POS 3.96MM VERT TIN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD827JR16REEL | 制造商:Analog 功能描述:Op Amp SOIC 16 Pin DUAL GP |
| AD827JR-16-REEL | 制造商:Analog 功能描述:Op Amp SOIC 16 Pin DUAL GP |
| AD827JR-16-REEL7 | 制造商:Analog Devices 功能描述:OP Amp Dual GP ±18V 16-Pin SOIC W T/R 制造商:Rochester Electronics LLC 功能描述:IC AP AMP, AD827JR IC - Tape and Reel |
| AD827JR-REEL | 制造商:AD 制造商全称:Analog Devices 功能描述:High Speed, Low Power Dual Op Amp |
| AD827JRZ-16 | 功能描述:IC OPAMP GP 50MHZ DUAL LP 16SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:1 系列:- 放大器类型:通用 电路数:4 输出类型:满摆幅 转换速率:0.028 V/µs 增益带宽积:105kHz -3db带宽:- 电流 - 输入偏压:3nA 电压 - 输入偏移:100µV 电流 - 电源:3.3µA 电流 - 输出 / 通道:12mA 电压 - 电源，单路/双路(±):2.7 V ~ 12 V，±1.35 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:14-TSSOP 包装:剪切带 (CT) 其它名称:OP481GRUZ-REELCT |
发布紧急采购，3分钟左右您将得到回复。