- 您现在的位置：买卖IC网 > PDF目录16543 > AD8280-EVALZ (Analog Devices Inc)BOARD EVAL FOR AD8280 PDF资料下载
参数资料
| 型号： | AD8280-EVALZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 17/24页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR AD8280 |
| 标准包装： | 1 |
| 主要目的： | 电源管理，电池监控器 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | AD8280 |
| 主要属性： | 带 2 个温度传感器的 3 ~ 6 个监视器单元 |
| 次要属性： | 过电压、欠电压和过热阈值可调节 |
| 已供物品： | 板 |
| 相关产品： | AD8280WASTZ-RL-ND - IC LI-ION BATT MON 48LQFP AD8280WASTZ-ND - IC LI-ION BATT MON 48LQFP |
AD8280
Also, if the resistor (R TOP ) used in the top of the thermistor
bridge circuit is less than 10 kΩ, another resistor (R IN ) must be
added in series to the input to the VTx pin (see Figure 46). The
two resistors together must be greater than 10 kΩ (R TOP + R IN >
10 kΩ). This configuration is required only if V TH is not the
AD8280 LDO.
V TH
+
+
+
+
VIN6
VIN5
VIN4
VIN3
VIN2
VIN1
R TOP
THERMISTOR
R IN
VTx
AD8280
VIN0
AD8280
Figure 48. Four-Cell Connections for the AD8280
Figure 46. Input Configuration for VTx When Not Using the LDO for V TH
The part can work with both negative temperature coefficient
VIN6
VIN5
(NTC) and positive temperature coefficient (PTC) thermistors.
For NTC, the NPTC pin should be tied to logic low (VBOTx
pin); for PTC, the NPTC pin should be tied to logic high (LDO
pin). If the part is set to NTC mode, the OT alarm is tripped
when the voltages at VT1 and VT2 drop below the trip point.
If the part is set to PTC mode, the OT alarm is tripped when
the voltages at VT1 and VT2 rise above the trip point.
+
+
+
VIN4
VIN3
VIN2
VIN1
VIN0
AD8280
NUMBER OF CELLS SELECTION
The part can be configured to work with three, four, five, or six
cells. Table 5 describes how to program the SEL0 and SEL1 pins
to determine the number of cells being monitored. A logic low
represents VBOTx, and a logic high represents the LDO output
voltage. Figure 47 through Figure 49 show how to connect the
cells to the part in a five-cell, four-cell, or three-cell application.
Table 5. SELx Pin Programming
Figure 49. Three-Cell Connections for the AD8280
THRESHOLD INPUTS
The thresholds (or trip points) are set externally with a voltage
divider providing maximum flexibility. The desired trip point
voltage is connected to the following pins: OV (overvoltage trip
point), UV (undervoltage trip point), and OT (overtemperature
trip point). The +5 V output of either the reference (REF) or the
LDO can be used as the top voltage of the divider. However,
because the reference output is more accurate than the LDO out-
Number of Cells Used
6 cells
5 cells (VIN5 shorted)
4 cells (VIN4 and VIN5 shorted)
3 cells (VIN3, VIN4, and VIN5 shorted)
SEL0
0
0
1
1
SEL1
0
1
0
1
put, the reference output is better suited to power the trip point
setting dividers. If the thermistor dividers used for temperature
sensing are driven from the LDO output, it is recommended that
the LDO be used to drive the OT trip point divider as well for
better temperature drift performance.
Decoupling capacitors (0.1 μF) should be used with the bottom
+
+
+
+
+
VIN6
VIN5
VIN4
VIN3
VIN2
VIN1
VIN0
leg of each divider in addition to a 2.2 μF capacitor at the REF
The REF pin should be loaded with no more than 25 kΩ of
resistance. Therefore, when using REF to drive three voltage
dividers (OV, UV, and OT), it is recommended that the resis-
tance of each divider total at least 75 kΩ. If driving only two
dividers (OV and UV) with the reference, each divider should
total no less than 50 kΩ.
AD8280
Figure 47. Five-Cell Connections for the AD8280
Rev. C | Page 17 of 24
相关PDF资料 |
PDF描述 |
|---|---|
| ECE-T2WP681EA | CAP ALUM 680UF 450V 20% SNAP |
| ECM22DRTH-S13 | CONN EDGECARD 44POS .156 EXTEND |
| MCP130T-270I/TT | IC SUPERVISOR 2.70V LOW SOT23 |
| ECE-T1JA273FA | CAP ALUM 27000UF 63V 20% SNAP |
| EBM25DRTF-S13 | CONN EDGECARD 50POS .156 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD8280WASTZ | 功能描述:IC LI-ION BATT MON 48LQFP RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:2,000 系列:Impedance Track™ 功能:燃料，电量检测计/监控器 电池化学:锂离子（Li-Ion） 电源电压:2.4 V ~ 2.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:20-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:20-TSSOP 包装:带卷 (TR) 产品目录页面:1020 (CN2011-ZH PDF) 配用:BQ27350EVM-ND - BQ27350EVM 其它名称:296-21665-2 |
| AD8280WASTZ-RL | 功能描述:IC LI-ION BATT MON 48LQFP RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| AD8283 | 制造商:AD 制造商全称:Analog Devices 功能描述:Radar Receive Path AFE: 6-Channel LNA/PGA/AAF with ADC |
| AD8283CP-EBZ | 功能描述:EVAL BOARD RADAR RX PATH AFE 制造商:analog devices inc. 系列:- 零件状态:有效 类型:放大器 频率:- 配套使用产品/相关产品:AD8283 所含物品:板 标准包装:1 |
| AD8283WBCPZ | 功能描述:IC RADAR RECEIVE AFE 6CH 72LFCSP RoHS:是 类别:RF/IF 和 RFID >> RF 其它 IC 和模块 系列:- 标准包装:100 系列:* |
发布紧急采购，3分钟左右您将得到回复。