- 您现在的位置：买卖IC网 > PDF目录5247 > AD8295ACPZ-RL (Analog Devices Inc)IC AMP INST 1MHZ TRPL LN 16LFCSP PDF资料下载
参数资料
| 型号： | AD8295ACPZ-RL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 13/28页 |
| 文件大小： | 0K |
| 描述： | IC AMP INST 1MHZ TRPL LN 16LFCSP |
| 标准包装： | 5,000 |
| 放大器类型： | 仪表 |
| 电路数： | 3 |
| 转换速率： | 2 V/µs |
| 增益带宽积： | 1MHz |
| -3db带宽： | 1.2MHz |
| 电流 - 输入偏压： | 500pA |
| 电压 - 输入偏移： | 120µV |
| 电流 - 电源： | 2mA |
| 电流 - 输出 / 通道： | 18mA |
| 电压 - 电源，单路/双路(±)： | 4.6 V ~ 36 V，±2.3 V ~ 18 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-VQFN，CSP |
| 供应商设备封装： | 16-LFCSP（4x4） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
AD8295
Rev. A | Page 20 of 2
8
Reference Terminal
The output voltage of the AD8295 instrumentation amplifier
is developed with respect to the potential on the reference
terminal (REF). This is useful when the output signal needs
to be offset to a precise dc level.
The reference pin input can be driven slightly beyond the rails.
The REF pin is protected with ESD diodes, and the REF voltage
should not exceed either +VS or VS by more than 0.3 V.
For best performance, the source impedance to the REF terminal
should be kept below 1 Ω. Additional impedance at the REF
terminal can significantly degrade the CMRR of the amplifier.
When the reference source has significant output impedance
(for example, a resistive voltage divider), buffer the signal before
driving the REF pin. Internal Op Amp A1 or A2 can be used for
this purpose, as shown in Figure 60.
07343-
010
+VS
REF
AD8295
REF
RA
+VS
RB
RA
RB
C
OP AMP
BUFFER
AD8295
INCORRECT
CORRECT
+
Figure 60. Driving the Reference Pin
Noise at the reference feeds directly to the output. Therefore, in
Figure 60, Capacitor C is added to filter out any high frequency
noise on the positive power supply line. For very clean supplies,
the capacitor may not be needed. The filter frequency is a trade-
off between noise rejection and start-up time, and is given by
the following equation:
B
A
B
A
PASS
LOW
R
C
f
+
π
=
2
1
LAYOUT
The AD8295 is a high precision device. To ensure optimum
performance at the PCB level, care must be taken in the board
layout. The AD8295 pins are arranged in a logical manner to
aid in this task.
Routing and Vias
Unlike most LFCSP packages, the AD8295 package was designed
without the thermal pad to allow routes and vias directly beneath
the chip. However, the manufacturing process leaves a very small
section of exposed metal at each of the package corners. This metal
is connected to –VS through the part. Because of the possibility
of a short, vias should not be placed under this exposed metal.
Careful board layout maximizes system performance. Traces
from the gain setting resistor to the RG pins should be kept as
short as possible to minimize parasitic inductance. To ensure
the most accurate output, the trace from the REF pin should
either be connected to the local ground of the AD8295 or to a
voltage that is referenced to the local ground of the AD8295.
Common-Mode Rejection over Frequency
The AD8295 has a higher CMRR over frequency than typical
in-amps, which gives it greater immunity to disturbances such
as line noise and its associated harmonics. The AD8295 pinout
and hidden paddle package were designed so that the board
designer can take full advantage of this performance with a
well-implemented layout.
Poor layout can cause some of the common-mode signal to be
converted to a differential signal before it reaches the in-amp.
Such conversions occur when one input path has a frequency
response that is different from the other. To keep CMRR across
frequency high, the input source impedance and capacitance of
each path should be closely matched. Additional source resistance
in the input path (for example, for input protection) should be
placed close to the in-amp inputs to minimize their interaction
with parasitic capacitance from the PCB traces.
Parasitic capacitance at the gain setting pins can also affect
CMRR over frequency. The traces to the RG resistor should be
kept as short as possible. If the board design has a component
at the gain setting pins (for example, a switch or jumper), the
part should be chosen so that the parasitic capacitance is as
small as possible.
Unused Op Amps
When not in use, the internal op amps should be connected in a
unity-gain configuration, with the noninverting input connected
to a bias point in the input range of the op amp. These connections
ensure that the AD8295 op amp uses minimum power and does
not disturb the internal power supplies of the AD8295. These
connections are shown as dotted lines in several of the applica-
tions figures.
Reference
The output voltage of the instrumentation amplifier section of
the AD8295 is developed with respect to the potential on the
reference terminal (REF); care should be taken to tie the REF
pin to the appropriate local ground (see Figure 61).
相关PDF资料 |
PDF描述 |
|---|---|
| LMP8270MA/NOPB | IC AMP PREC DIFF 8-SOIC |
| TA45-A443H080C0 | CIRCUIT BRKR THERMAL 8A 2POLE |
| OP262GSZ-REEL | IC OPAMP GP R-R 15MHZ DUAL 8SOIC |
| MCP6241UT-E/OT | IC OPAMP SNGL 1.8V SOT23-5 |
| TA45-A443HJ20C0 | CIRCUIT BRKR THERMAL 2A 2POLE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD8295ACPZ-WP | 功能描述:IC AMP INST 1MHZ TRPL LN 16LFCSP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:1 系列:- 放大器类型:通用 电路数:4 输出类型:满摆幅 转换速率:0.028 V/µs 增益带宽积:105kHz -3db带宽:- 电流 - 输入偏压:3nA 电压 - 输入偏移:100µV 电流 - 电源:3.3µA 电流 - 输出 / 通道:12mA 电压 - 电源，单路/双路(±):2.7 V ~ 12 V，±1.35 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:14-TSSOP 包装:剪切带 (CT) 其它名称:OP481GRUZ-REELCT |
| AD8295BCPZ-R7 | 功能描述:IC AMP INST 1MHZ TRPL LN 16LFCSP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:- 放大器类型:J-FET 电路数:2 输出类型:- 转换速率:13 V/µs 增益带宽积:3MHz -3db带宽:- 电流 - 输入偏压:65pA 电压 - 输入偏移:3000µV 电流 - 电源:1.4mA 电流 - 输出 / 通道:- 电压 - 电源，单路/双路(±):7 V ~ 36 V，±3.5 V ~ 18 V 工作温度:-40°C ~ 85°C 安装类型:通孔 封装/外壳:8-DIP（0.300"，7.62mm） 供应商设备封装:8-PDIP 包装:管件 |
| AD8295BCPZ-RL | 功能描述:IC IN AMP PREC FE +/-18V 16LFCSP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:- 放大器类型:J-FET 电路数:2 输出类型:- 转换速率:13 V/µs 增益带宽积:3MHz -3db带宽:- 电流 - 输入偏压:65pA 电压 - 输入偏移:3000µV 电流 - 电源:1.4mA 电流 - 输出 / 通道:- 电压 - 电源，单路/双路(±):7 V ~ 36 V，±3.5 V ~ 18 V 工作温度:-40°C ~ 85°C 安装类型:通孔 封装/外壳:8-DIP（0.300"，7.62mm） 供应商设备封装:8-PDIP 包装:管件 |
| AD8295BCPZ-WP | 功能描述:IC IN AMP PREC FE +/-18V 16LFCSP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:1 系列:- 放大器类型:通用 电路数:4 输出类型:满摆幅 转换速率:0.028 V/µs 增益带宽积:105kHz -3db带宽:- 电流 - 输入偏压:3nA 电压 - 输入偏移:100µV 电流 - 电源:3.3µA 电流 - 输出 / 通道:12mA 电压 - 电源，单路/双路(±):2.7 V ~ 12 V，±1.35 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:14-TSSOP 包装:剪切带 (CT) 其它名称:OP481GRUZ-REELCT |
| AD829AQ | 功能描述:IC VIDEO OPAMP HS LN 8-CDIP RoHS:否 类别:集成电路 (IC) >> 线性 - 放大器 - 视频放大器和频缓冲器 系列:- 标准包装:1,000 系列:- 应用:驱动器 输出类型:差分 电路数:3 -3db带宽:350MHz 转换速率:1000 V/µs 电流 - 电源:14.5mA 电流 - 输出 / 通道:60mA 电压 - 电源，单路/双路(±):5 V ~ 12 V，±2.5 V ~ 6 V 安装类型:表面贴装 封装/外壳:20-VFQFN 裸露焊盘 供应商设备封装:20-QFN 裸露焊盘（4x4） 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。