参数资料
| 型号： | AD8310ARMZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 14/24页 |
| 文件大小： | 0K |
| 描述： | IC LOGARITHMIC AMP 95DB 8-MSOP |
| 产品培训模块： | Choosing and Using RF Detectors |
| 标准包装： | 50 |
| 类型： | 对数放大器 |
| 应用： | 接收器信号强度指示（RSSI） |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-MSOP |
| 包装： | 管件 |
| 产品目录页面： | 550 (CN2011-ZH PDF) |
AD8310
Rev. F | Page 21 of 24
Table 6. Evaluation Board Setup Options
Component
Function
Default Condition
TP1, TP2
Supply and Ground Vector Pins.
Not applicable
SW1
Device Enable. When in Position A, the ENBL pin is connected to +VS, and the AD8310 is in normal
operating mode. When in Position B, the ENBL pin is connected to ground, putting the device into
sleep mode.
SW1 = A
R1/R4
SMA Connector Grounds. Connects common of INHI and INLO SMA connectors to ground. They
can be used to isolate the generator ground from the evaluation board ground. See Figure 28.
R1 = R4 = 0 Ω
C1, C2, R3
Input Interface. R3 (52.3 Ω) combines with the AD8310’s 1 kΩ input impedance to give an overall
broadband input impedance of 50 Ω. C1, C2, and the AD8310’s input impedance combine to set a
high-pass input corner of 32 kHz. Alternatively, R3, C1, and C2 can be replaced by an inductor and
matching capacitors to form an input matching network. See the Input Matching section for details.
R3 = 52.3 Ω,
C1 = C2 = 0.01 μF
C3
RSSI (Video) Bandwidth Adjust. The addition of C3 (farads) lowers the RSSI bandwidth of the
AD8310’s output according to the following equation:
CFILT = 1/(2π × 3 kΩ Video Bandwidth) 2.1 pF
C3 = open
C4, C5, R5
Supply Decoupling. The normal supply decoupling of 0.01 μF (C4) can be augmented by a larger
capacitor in C5. An inductor or small resistor can be placed in R5 for additional decoupling.
C4 = 0.01 μF,
C5 = open, R5 = 0 Ω
R6
Output Source Impedance. In cable-driving applications, a resistor (typically 50 Ω or 75 Ω) can be
placed in R6 to give the circuit a back-terminated output impedance.
R6 = 0 Ω
W1, W2, C6, R7
Output Loading. Resistors and capacitors can be placed in C6 and R7 to load-test VOUT. Jumper W1
and Jumper W2 are used to connect or disconnect the loads.
C6 = R7 = open,
W1 = W2 = installed
C7
Offset Compensation Loop. A capacitor in C7 reduces the corner frequency of the offset control
loop in low frequency applications.
C7 = open
相关PDF资料 |
PDF描述 |
|---|---|
| VE-273-MW-B1 | CONVERTER MOD DC/DC 24V 100W |
| AD8305ACPZ-RL7 | IC LOGARITH CONV 100DB 16-LFCSP |
| VE-2WF-IV-F2 | CONVERTER MOD DC/DC 72V 150W |
| VE-J3P-MW-S | CONVERTER MOD DC/DC 13.8V 100W |
| VE-2WF-IV-F1 | CONVERTER MOD DC/DC 72V 150W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD8310ARMZ | 制造商:Analog Devices 功能描述:Operational Amplifier (Op-Amp) IC |
| AD8310ARMZ-REEL1 | 制造商:AD 制造商全称:Analog Devices 功能描述:Fast, Voltage-Out DC-440 MHz, 95 dB Logarithmic Amplifier |
| AD8310ARMZ-REEL7 | 功能描述:IC AMP LOGARITHMIC 8MSOP RoHS:是 类别:集成电路 (IC) >> 线性 - 放大器 - 专用 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:60 系列:- 类型:可变增益放大器 应用:CATV 安装类型:表面贴装 封装/外壳:20-WQFN 裸露焊盘 供应商设备封装:20-TQFN-EP（5x5） 包装:托盘 |
| AD8310ARMZ-REEL71 | 制造商:AD 制造商全称:Analog Devices 功能描述:Fast, Voltage-Out DC-440 MHz, 95 dB Logarithmic Amplifier |
| AD8310-EVAL | 制造商:Analog Devices 功能描述:AD8310 EVALUATION BOARD - Bulk |
发布紧急采购，3分钟左右您将得到回复。