- 您现在的位置：买卖IC网 > PDF目录97841 > AD8349AREZ-REEL7 (ANALOG DEVICES INC) 700 MHz - 2700 MHz RF/MICROWAVE QPSK MODULATOR PDF资料下载
参数资料
| 型号： | AD8349AREZ-REEL7 |
| 厂商： | ANALOG DEVICES INC |
| 元件分类： | 调制器/解调器 |
| 英文描述： | 700 MHz - 2700 MHz RF/MICROWAVE QPSK MODULATOR |
| 封装： | LEAD FREE, MO-153ABT, TSSOP-16 |
| 文件页数： | 11/28页 |
| 文件大小： | 729K |
| 代理商： | AD8349AREZ-REEL7 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
AD8349
Rev. A | Page 19 of 28
–90
–80
–70
–60
–50
–40
–30
–20
–10
0
10
AMP
L
ITUDE
(dBm)
SSB = 1.7dBm
LO = –44.5dBm
USB = –52dBc
THIRD HARMONIC = –36.8dBc
03570-0-054
CENTER 2.14GHz
SPAN 10MHz
Figure 53. AD8349 Single Sideband Spectrum at 2140 MHz
REDUCING UNDESIRED SIDEBAND LEAKAGE
Undesired sideband leakage is the result of phase and amplitude
imbalances between the I and Q channel baseband signals.
Therefore, to reduce the undesired sideband leakage, the
amplitude and phase of the baseband signals have to be
matched at the mixer cores. Because of mismatches in the
baseband input paths leading to the mixers, perfectly matched
baseband signals at the pins of the device may not be perfectly
matched when they reach the mixers. Therefore, slight
adjustments have to be made to the phase and amplitudes of the
baseband signals to compensate for these mismatches.
Begin by making one of the inputs, say the I channel, the
reference signal. Then adjust the amplitude and phase of the
Q channel’s signal until the unwanted sideband power reaches a
trough. The AD9777 has built-in gain adjust registers that allow
this to be performed easily. If an iterative adjustment is
performed between the amplitude and the phase, the undesired
sideband leakage can be minimized significantly.
Note that the compensated sideband rejection performance
degrades as the operating baseband frequency is moved away
from the frequency at which the compensation was performed.
As a result, the frequency of the I and Q sine waves should be
approximately half the baseband bandwidth of the modulated
carrier. For example, if the modulator is being used to transmit
a single WCDMA carrier whose baseband spectrum spans from
dc to 3.84/2 MHz, the calibration could be effectively performed
with 1 MHz I and Q sine waves.
REDUCTION OF LO FEEDTHROUGH
Because the I and Q signals are being multiplied with the LO,
any internal offset voltages on these inputs will result in leakage
of the LO to the output. Additionally, any imbalance in the LO
to RF in the mixers will also cause the LO signal to leak through
the mixer to the RF output. The LO feedthrough is clearly
visible in the single sideband spectrum. The nominal LO
feedthrough of –42 dBm can be reduced further by applying
offset compensation voltages on the I and Q inputs. Note that
the LO feedthrough is reduced by varying the differential offset
voltages on the I and Q inputs (xBBP – xBBN), not by varying
the nominal bias level of 400 mV. This is easily accomplished by
programming and then storing the appropriate DAC offset code
required to minimize the LO feedthrough. This, however,
requires a dc-coupled path from the DAC to the I and Q inputs.
The procedure for reducing the LO feedthrough is simple. A
differential offset voltage is applied from the I DAC until the LO
feedthrough reaches a trough. With this offset level held, a
differential offset voltage is applied to the Q DAC until a lower
trough is reached (This is an iterative process).
Figure 54 shows a plot of LO feedthrough vs. I channel offset (in
mV) after the Q channel offset has been nulled. This suggests
that the compensating offset voltage should have a resolution of
at least 100 V to reduce the LO feedthrough to be less than –
65 dBm. Figure 55 shows the single sideband spectrum at 2140
MHz after the nulling of the LO. The reduced LO feedthrough
can clearly be seen when compared with the performance
shown in Figure 53.
Compensated LO feedthrough degrades somewhat as the LO
frequency is moved away from the frequency at which the
compensation was performed. This variation is very small
across a 30 MHz or 60 MHz cellular band, however. This small
variation is due to the effects of LO-to-RF output leakage
around the package and on the board.
–70
–60
–58
–56
–54
–52
CARRIE
R
FE
E
D
THROUGH
(dBm)
–62
–68
–66
–64
3.0
4.0
4.5
5.0
5.5
3.5
IOPP-IOPN (mV)
03570-0-055
Figure 54. Plot of LO Feedthrough vs. I Channel Baseband Offset
(Q Channel Offset Nulled)
相关PDF资料 |
PDF描述 |
|---|---|
| AD8350ARMZ20 | 1000 MHz RF/MICROWAVE WIDE BAND MEDIUM POWER AMPLIFIER |
| AD8350ARZ20 | 1000 MHz RF/MICROWAVE WIDE BAND MEDIUM POWER AMPLIFIER |
| AD8350ARZ15-REEL7 | 1000 MHz RF/MICROWAVE WIDE BAND MEDIUM POWER AMPLIFIER |
| AD8350ARMZ15-REEL7 | 1000 MHz RF/MICROWAVE WIDE BAND MEDIUM POWER AMPLIFIER |
| AD8350ARMZ20-REEL7 | 1000 MHz RF/MICROWAVE WIDE BAND MEDIUM POWER AMPLIFIER |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD8349AREZ-RL7 | 功能描述:IC MOD QUAD 2.7GHZ 16TSSOP RoHS:是 类别:RF/IF 和 RFID >> RF 调制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:调制器 LO 频率:700MHz ~ 2.3GHz RF 频率:700MHz ~ 2.3GHz P1dB:1dBm 底噪:-148dBm/Hz 输出功率:-1dBm 电流 - 电源:46mA 电源电压:2.7 V ~ 3.6 V 测试频率:1.75GHz 封装/外壳:28-WFQFN 裸露焊盘 包装:带卷 (TR) |
| AD8349EVAL | 制造商:Analog Devices 功能描述:IC ((NS)) |
| AD8349-EVAL | 制造商:Analog Devices 功能描述:AD8349 EVALUATION BOARD - Bulk |
| AD8349-EVALZ | 制造商:Analog Devices 功能描述:AD8349 EVALUATION BOARD - Bulk |
| AD8349XRE | 制造商:Analog Devices 功能描述:800 MHZ - 2.7 GHZ QUADRATURE MODULATOR - Rail/Tube |
发布紧急采购，3分钟左右您将得到回复。