参数资料
| 型号： | AD8397ARZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 3/16页 |
| 文件大小： | 0K |
| 描述： | IC OPAMP VF R-R DUAL LN 8SOIC |
| 标准包装： | 98 |
| 放大器类型： | 电压反馈 |
| 电路数： | 2 |
| 输出类型： | 满摆幅 |
| 转换速率： | 53 V/µs |
| -3db带宽： | 69MHz |
| 电流 - 输入偏压： | 200pA |
| 电压 - 输入偏移： | 1000µV |
| 电流 - 电源： | 11mA |
| 电流 - 输出 / 通道： | 310mA |
| 电压 - 电源，单路/双路(±)： | 3 V ~ 24 V，±1.5 V ~ 12 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SO |
| 包装： | 管件 |
| 产品目录页面： | 766 (CN2011-ZH PDF) |
| 其它名称： | Q2528981 |
AD8397
Rev. A | Page 11 of 16
APPLICATIONS INFORMATION
The AD8397 is a voltage feedback operational amplifier that
features an H-bridge input stage and common-emitter, rail-to-rail
output stage. The AD8397 can operate from a wide supply range,
±1.5 V to ±12 V. When driving light loads, the rail-to-rail output is
capable of swinging to within 0.2 V of either rail. The output can
also deliver high linear output current when driving heavy loads,
up to 310 mA into 32 Ω while maintaining 80 dBc SFDR. The
AD8397 is fabricated on Analog Devices proprietary XFCB-HV.
POWER SUPPLY AND DECOUPLING
The AD8397 can be powered with a good quality, well-regulated,
low noise supply from ±1.5 V to ±12 V. Pay careful attention to
decoupling the power supply. Use high quality capacitors with
low equivalent series resistance (ESR), such as multilayer
ceramic capacitors (MLCCs), to minimize the supply voltage
ripple and power dissipation. Locate a 0.1 μF MLCC decoupling
capacitor(s) no more than 1/8 inch away from the power supply
pin(s). A large tantalum 10 μF to 47 μF capacitor is recommended
to provide good decoupling for lower frequency signals and to
supply current for fast, large signal changes at the AD8397 outputs.
LAYOUT CONSIDERATIONS
As with all high speed applications, pay careful attention to
printed circuit board (PCB) layout to prevent associated board
parasitics from becoming problematic. The PCB should have a
low impedance return path (or ground) to the supply. Removing
the ground plane from all layers in the immediate area of the
amplifier helps to reduce stray capacitances. The signal routing
should be short and direct in order to minimize the parasitic
inductance and capacitance associated with these traces. Locate
termination resistors and loads as close as possible to their
respective inputs and outputs. Keep input traces as far apart as
possible from the output traces to minimize coupling (crosstalk)
though the board.
When the AD8397 is configured as a differential driver, as in
some line driving applications, provide a symmetrical layout to
the extent possible in order to maximize balanced performance.
When running differential signals over a long distance, the traces
on the PCB should be close together or any differential wiring
should be twisted together to minimize the area of the inductive
loop that is formed. This reduces the radiated energy and makes
the circuit less susceptible to RF interference. Adherence to
stripline design techniques for long signal traces (greater than
approximately 1 inch) is recommended.
UNITY-GAIN OUTPUT SWING
When operating the AD8397 in a unity-gain configuration,
the output does not swing to the rails and is constrained by
the H-bridge input. This can be seen by comparing the output
overdrive recovery in Figure 7 and the input overdrive recovery in
Figure 22. To avoid overdriving the input and to realize the full
swing afforded by the rail-to-rail output stage, use the amplifier
in a gain of two or greater.
05069-
028
INPUT
OUTPUT
7
–1
0
1
0
80
160
240
320
400
TIME (ns)
480
560
640
720
800
2
3
4
5
6
V
O
LTS
Figure 22. Unity-Gain Input Overdrive Recovery
相关PDF资料 |
PDF描述 |
|---|---|
| LTC6079IGN#PBF | IC OP AMP QUAD R-R I/O 16SSOP |
| LTC6079IDHC#PBF | IC OP AMP QUAD R-R I/O 16DFN |
| AD8557ARZ | IC AMP CHOPPER 2MHZ 55MA 8SOIC |
| OP270GPZ | IC OPAMP GP 5MHZ DUAL PREC 8DIP |
| AD8622ARZ-REEL7 | IC OPAMP GP R-R 540KHZ LP 8SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD8397ARZ-REEL | 功能描述:IC OPAMP VF R-R DUAL LN 8SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 其它有关文件:Automotive Product Guide 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 放大器类型:通用 电路数:1 输出类型:满摆幅 转换速率:3 V/µs 增益带宽积:10MHz -3db带宽:- 电流 - 输入偏压:1pA 电压 - 输入偏移:70µV 电流 - 电源:2.5mA 电流 - 输出 / 通道:48mA 电压 - 电源，单路/双路(±):2.7 V ~ 5.5 V，±1.35 V ~ 2.75 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:Digi-Reel® 其它名称:MAX4475AUT#TG16DKR |
| AD8397ARZ-REEL7 | 功能描述:IC OPAMP VF R-R DUAL LN 8SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:100 系列:- 放大器类型:通用 电路数:1 输出类型:- 转换速率:0.2 V/µs 增益带宽积:- -3db带宽:- 电流 - 输入偏压:100pA 电压 - 输入偏移:30µV 电流 - 电源:380µA 电流 - 输出 / 通道:- 电压 - 电源，单路/双路(±):±2 V ~ 18 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SO 包装:管件 |
| AD8398 | 制造商:AD 制造商全称:Analog Devices 功能描述:VDSL, Dual Line Driver with Shutdown |
| AD8398A | 制造商:AD 制造商全称:Analog Devices 功能描述:Single Port VDSL2 Line Driver with Shutdown |
| AD8398AACPZ-R2 | 制造商:Analog Devices 功能描述:SINGLE PORT VDSL2 LINE DRIVER WITH SHUTDOWN - Tape and Reel 制造商:Analog Devices 功能描述:IC LINE DRVR DUAL VDSL 16-LFCSP 制造商:Analog Devices 功能描述:IC, LINE DRIVER, DUAL, LFCSP-16 制造商:Analog Devices 功能描述:IC, DIFF LINE DRIVER, DUAL, LFCSP-16, IC Interface Type:-, No. of Drivers:2 |
发布紧急采购，3分钟左右您将得到回复。