- 您现在的位置：买卖IC网 > PDF目录9297 > AD8402ARUZ10-REEL (Analog Devices Inc)IC POT DIG DUAL 10K 8BIT 14TSSOP PDF资料下载
参数资料
| 型号： | AD8402ARUZ10-REEL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 13/32页 |
| 文件大小： | 0K |
| 描述： | IC POT DIG DUAL 10K 8BIT 14TSSOP |
| 标准包装： | 2,500 |
| 接片： | 256 |
| 电阻（欧姆）： | 10k |
| 电路数： | 2 |
| 温度系数： | 标准值 500 ppm/°C |
| 存储器类型： | 易失 |
| 接口： | 3 线 SPI（芯片选择） |
| 电源电压： | 2.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 14-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 14-TSSOP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
AD8400/AD8402/AD8403
Rev. E | Page 20 of 32
THEORY OF OPERATION
The AD8400/AD8402/AD8403 provide a single, dual, and quad
channel, 256-position, digitally controlled variable resistor (VR)
device. Changing the programmed VR setting is accomplished
by clocking in a 10-bit serial data-word into the SDI (Serial
Data Input) pin. The format of this data-word is two address
bits, MSB first, followed by eight data bits, also MSB first.
Table 6 provides the serial register data-word format. The
AD8400/AD8402/AD8403 have the following address assign-
ments for the ADDR decoder, which determines the location
of the VR latch receiving the serial register data in Bit B7 to
Bit B0:
VR# = A1 × 2 + A0 + 1
(1)
The single-channel AD8400 requires A1 = A0 = 0. The dual-
channel AD8402 requires A1 = 0. VR settings can be changed
one at a time in random sequence. A serial clock running at
10 MHz makes it possible to load all four VRs under 4 μs
(10 × 4 × 100 ns) for AD8403. The exact timing requirements
The AD8400/AD8402/AD8403 do not have power-on midscale
preset, so the wiper can be at any random position at power-up.
However, the AD8402/AD8403 can be reset to midscale by
asserting the RS pin, simplifying initial conditions at power-up.
Both parts have a power shutdown SHDN pin that places the
VR in a zero-power-consumption state where Terminal Ax is
open-circuited and the Wiper Wx is connected to Terminal Bx,
resulting in the consumption of only the leakage current in the
VR. In shutdown mode, the VR latch settings are maintained
so that upon returning to the operational mode, the VR settings
return to the previous resistance values. The digital interface is
still active in shutdown, except that SDO is deactivated. Code
changes in the registers can be made during shutdown that will
produce new wiper positions when the device is taken out of
shutdown.
D7
D6
D5
D4
D3
D2
D1
D0
RDAC
LATCH
AND
DECODER
Ax
Wx
Bx
RS =RNOMINAL/256
RS
SHDN
RS
01
09
2-
0
44
Figure 45. AD8402/AD8403 Equivalent VR (RDAC) Circuit
PROGRAMMING THE VARIABLE RESISTOR
Rheostat Operation
The nominal resistance of the VR (RDAC) between Terminal A
and Terminal B is available with values of 1 kΩ, 10 kΩ, 50 kΩ,
and 100 kΩ. The final digits of the part number determine the
nominal resistance value; that is, 10 kΩ = 10; 100 kΩ = 100.
The nominal resistance (RAB) of the VR has 256 contact points
accessible by the wiper terminal, and the resulting resistance
can be measured either across the wiper and B terminals (RWB)
or across the wiper and A terminals (RWA). The 8-bit data-word
loaded into the RDAC latch is decoded to select one of the
256 possible settings. The wiper’s first connection starts at the
B terminal for data 00H. This B terminal connection has a wiper
contact resistance of 50 Ω. The second connection (for the 10 kΩ
part) is the first tap point located at 89 Ω = [RAB (nominal
resistance) + RW = 39 Ω + 50 Ω] for data 01H. The third
connection is the next tap point representing 78 Ω + 50 Ω =
128 Ω for data 02H. Each LSB data value increase moves the
wiper up the resistor ladder until the last tap point is reached at
10,011 Ω. Note that the wiper does not directly connect to the
diagram of the equivalent RDAC circuit.
The AD8400 contains one RDAC, the AD8402 contains
two independent RDACs, and the AD8403 contains four
independent RDACs. The general transfer equation that
determines the digitally programmed output resistance
between Wx and Bx is
()
W
AB
WB
R
D
R
+
×
=
256
(2)
where D, in decimal, is the data loaded into the 8-bit RDAC#
latch, and RAB is the nominal end-to-end resistance.
For example, when the A terminal is either open-circuited or
tied to the Wiper W, the following RDAC latch codes result in
the following RWB (for the 10 kΩ version):
Table 10.
D (Dec)
RWB (
)
Output State
255
10,011
Full scale
128
5,050
Midscale (RS = 0 condition)
1
89
1 LSB
0
50
Zero-scale (wiper contact resistance)
Note that in the zero-scale condition, a finite wiper resistance of
50 Ω is present. Care should be taken to limit the current flow
between W and B in this state to a maximum value of 5 mA to
avoid degradation or possible destruction of the internal switch
contact.
相关PDF资料 |
PDF描述 |
|---|---|
| VI-24Y-MW-F1 | CONVERTER MOD DC/DC 3.3V 66W |
| AD8402ARUZ1-REEL | IC POT DIG DUAL 1K 8BIT 14TSSOP |
| MS3102E22-14PY | CONN RCPT 19POS BOX MNT W/PINS |
| AD5252BRUZ50-RL7 | IC POT DGTL DL 50K 256P 14TSSOP |
| MS3101A36-15S | CONN RCPT 35POS FREE HNG W/SCKT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD8402ARUZ1-REEL | 功能描述:IC POT DIG DUAL 1K 8BIT 14TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:- 标准包装:3,000 系列:DPP 接片:32 电阻（欧姆）:10k 电路数:1 温度系数:标准值 300 ppm/°C 存储器类型:非易失 接口:3 线串行（芯片选择，递增，增/减） 电源电压:2.5 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WFDFN 裸露焊盘 供应商设备封装:8-TDFN（2x3） 包装:带卷 (TR) |
| AD8402ARUZ50 | 功能描述:IC POT DIG DUAL 50K 8BIT 14TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:- 标准包装:3,000 系列:DPP 接片:32 电阻（欧姆）:10k 电路数:1 温度系数:标准值 300 ppm/°C 存储器类型:非易失 接口:3 线串行（芯片选择，递增，增/减） 电源电压:2.5 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WFDFN 裸露焊盘 供应商设备封装:8-TDFN（2x3） 包装:带卷 (TR) |
| AD8402ARUZ50-REEL | 功能描述:IC POT DIG DUAL 50K 8BIT 14TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:- 标准包装:2,500 系列:XDCP™ 接片:256 电阻（欧姆）:100k 电路数:1 温度系数:标准值 ±300 ppm/°C 存储器类型:非易失 接口:I²C（设备位址） 电源电压:2.7 V ~ 5.5 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:14-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:14-TSSOP 包装:带卷 (TR) |
| AD8402ARZ1 | 功能描述:IC POT DIG DUAL 1K 8BIT 14SOIC RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 接片:256 电阻（欧姆）:100k 电路数:1 温度系数:标准值 35 ppm/°C 存储器类型:非易失 接口:3 线串口 电源电压:2.7 V ~ 5.25 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WDFN 裸露焊盘 供应商设备封装:8-TDFN-EP（3x3） 包装:剪切带 (CT) 产品目录页面:1399 (CN2011-ZH PDF) 其它名称:MAX5423ETA+TCT |
| AD8402ARZ10 | 功能描述:IC POT DGTL DUAL 10K 8BIT 14SOIC RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 接片:256 电阻（欧姆）:100k 电路数:1 温度系数:标准值 35 ppm/°C 存储器类型:非易失 接口:3 线串口 电源电压:2.7 V ~ 5.25 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WDFN 裸露焊盘 供应商设备封装:8-TDFN-EP（3x3） 包装:剪切带 (CT) 产品目录页面:1399 (CN2011-ZH PDF) 其它名称:MAX5423ETA+TCT |
发布紧急采购，3分钟左右您将得到回复。