参数资料
| 型号： | AD8402ARZ10 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 17/32页 |
| 文件大小： | 0K |
| 描述： | IC POT DGTL DUAL 10K 8BIT 14SOIC |
| 标准包装： | 56 |
| 接片： | 256 |
| 电阻（欧姆）： | 10k |
| 电路数： | 2 |
| 温度系数： | 标准值 500 ppm/°C |
| 存储器类型： | 易失 |
| 接口： | 3 线 SPI（芯片选择） |
| 电源电压： | 2.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 14-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 14-SOICN |
| 包装： | 管件 |
| 产品目录页面： | 787 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
AD8400/AD8402/AD8403
Rev. E | Page 24 of 32
APPLICATIONS
INVERTING GAIN (V/V)
256
128
0
0.1
1
10
96
64
32
160
192
224
DI
G
IT
A
L
CO
DE
(D
eci
mal
)
01
09
2-
05
3
The digital potentiometer (RDAC) allows many of the applica-
tions of a mechanical potentiometer to be replaced by a solid-
state solution offering compact size and freedom from vibration,
shock, and open contact problems encountered in hostile
environments. A major advantage of the digital potentiometer
is its programmability. Any settings can be saved for later recall
in system memory.
The two major configurations of the RDAC include the
potentiometer divider (basic 3-terminal application) and
the rheostat (2-terminal configuration) connections shown
Certain boundary conditions must be satisfied for proper
AD8400/AD8402/AD8403 operation. First, all analog signals
must remain within the GND to VDD range used to operate the
single-supply AD8400/AD8402/AD8403. For standard
potentiometer divider applications, the wiper output can be
used directly. For low resistance loads, buffer the wiper with
a suitable rail-to-rail op amp such as the OP291 or the OP279.
Second, for ac signals and bipolar dc adjustment applications,
a virtual ground is generally needed. Whichever method is used
to create the virtual ground, the result must provide the necessary
sink and source current for all connected loads, including
adequate bypass capacitance. Figure 41 shows one channel of
the AD8402 connected in an inverting programmable gain
amplifier circuit. The virtual ground is set at 2.5 V, which allows
the circuit output to span a ±2.5 V range with respect to virtual
ground. The rail-to-rail amplifier capability is necessary for the
widest output swing. As the wiper is adjusted from its midscale
reset position (80H) toward the A terminal (code FFH), the
voltage gain of the circuit is increased in successively larger
increments. Alternatively, as the wiper is adjusted toward the B
terminal (code 00H), the signal becomes attenuated. The plot in
Figure 54 shows the wiper settings for a 100:1 range of voltage
gain (V/V). Note the ±10 dB of pseudologarithmic gain around
0 dB (1 V/V). This circuit is mainly useful for gain adjustments
in the range of 0.14 V/V to 4 V/V; beyond this range the step
sizes become very large, and the resistance of the driving circuit
can become a significant term in the gain equation.
Figure 54. Inverting Programmable Gain Plot
ACTIVE FILTER
The state variable active filter is one of the standard circuits
used to generate a low-pass, high-pass, or band-pass filter.
The digital potentiometer allows full programmability of the
frequency, gain, and Q of the filter outputs. Figure 55 shows
the filter circuit using a 2.5 V virtual ground, which allows a
±2.5 VP input and output swing. RDAC2 and RDAC3 set the
LP, HP, and BP cutoff and center frequencies, respectively.
These variable resistors should be programmed with the same
data (as with ganged potentiometers) to maintain the best
Circuit Q. Figure 56 shows the measured filter response at the
band-pass output as a function of the RDAC2 and RDAC3
settings that produce a range of center frequencies from 2 kHz
to 20 kHz. The filter gain response at the band-pass output is
shown in Figure 57. At a center frequency of 2 kHz, the gain is
adjusted over a 20 dB to +20 dB range determined by RDAC1.
Circuit Q is adjusted by RDAC4. For more detailed reading on
the state variable active filter, see Analog Devices’ application
note AN-318.
A1
RDAC1
VIN
B
A2
A3
A4
RDAC4
B
10k
Ω
10k
Ω
OP279 × 2
RDAC2
RDAC3
B
0.01
μF
0.01
μF
BAND-
PASS
HIGH-
PASS
LOW-
PASS
0
1
092-
054
Figure 55. Programmable State Variable Active Filter
相关PDF资料 |
PDF描述 |
|---|---|
| DS4000GF/WBGA | IC OSC TCXO 16.384MHZ 24-BGA |
| DS4000GFN/WBGA | IC OSC TCXO 16.384MHZ 24-BGA |
| AD8402ARUZ1 | IC POT DIG 8BIT DUAL 1K 14-TSSOP |
| FST16211MTD | IC SWITCH BUS 24BIT TTL 56TSSOP |
| AD5272BRMZ-100 | IC RHEOSTAT 5V 50TP 1024 10MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD8402ARZ10 | 制造商:Analog Devices 功能描述:Digital Potentiometer |
| AD8402ARZ100 | 功能描述:IC POT DIG DUAL 100K 8BIT 14SOIC RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 接片:256 电阻（欧姆）:100k 电路数:1 温度系数:标准值 35 ppm/°C 存储器类型:非易失 接口:3 线串口 电源电压:2.7 V ~ 5.25 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WDFN 裸露焊盘 供应商设备封装:8-TDFN-EP（3x3） 包装:剪切带 (CT) 产品目录页面:1399 (CN2011-ZH PDF) 其它名称:MAX5423ETA+TCT |
| AD8402ARZ100-REEL | 功能描述:IC POT DIG DUAL 100K 8BIT 14SOIC RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:- 标准包装:3,000 系列:DPP 接片:32 电阻（欧姆）:10k 电路数:1 温度系数:标准值 300 ppm/°C 存储器类型:非易失 接口:3 线串行（芯片选择，递增，增/减） 电源电压:2.5 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WFDFN 裸露焊盘 供应商设备封装:8-TDFN（2x3） 包装:带卷 (TR) |
| AD8402ARZ10-REEL | 功能描述:IC POT DIG DUAL 10K 8BIT 14SOIC RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:- 标准包装:3,000 系列:DPP 接片:32 电阻（欧姆）:10k 电路数:1 温度系数:标准值 300 ppm/°C 存储器类型:非易失 接口:3 线串行（芯片选择，递增，增/减） 电源电压:2.5 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WFDFN 裸露焊盘 供应商设备封装:8-TDFN（2x3） 包装:带卷 (TR) |
| AD8402ARZ1-REEL | 功能描述:IC POT DIG DUAL 1K 8BIT 14SOIC RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:- 标准包装:3,000 系列:DPP 接片:32 电阻（欧姆）:10k 电路数:1 温度系数:标准值 300 ppm/°C 存储器类型:非易失 接口:3 线串行（芯片选择，递增，增/减） 电源电压:2.5 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WFDFN 裸露焊盘 供应商设备封装:8-TDFN（2x3） 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。