- 您现在的位置：买卖IC网 > PDF目录373947 > AD841KQ (ANALOG DEVICES INC) Wideband, Unity-Gain Stable, Fast Settling Op Amp PDF资料下载
参数资料
| 型号： | AD841KQ |
| 厂商： | ANALOG DEVICES INC |
| 元件分类： | 运动控制电子 |
| 英文描述： | Wideband, Unity-Gain Stable, Fast Settling Op Amp |
| 中文描述： | OP-AMP, 3300 uV OFFSET-MAX, 40 MHz BAND WIDTH, CDIP14 |
| 封装： | HERMETIC SEALED, CERDIP-14 |
| 文件页数： | 7/8页 |
| 文件大小： | 354K |
| 代理商： | AD841KQ |
Figure 22. AD841 0.01% Settling Time
Expressed in these terms, the measurement of settling time is obvi-
ously a challenge and needs to be done accurately to assure the
user that the amplifier is worth consideration for the application.
Figure 23. Settling Time Test Circuit
Measurement of the AD841’s 0.01% settling in 110 ns was ac-
complished by amplifying the error signal from a false summing
junction with a very high speed proprietary hybrid error ampli-
fier specially designed to enable testing of small settling errors.
The device under test was driving a 500
load. The input to
the error amp is clamped in order to avoid possible problems as-
sociated with the overdrive recovery of the oscilloscope input
amplifier. The error amp gains the error from the false summing
junction by 10, and it contains a gain vernier to fine trim the
gain.
Figure 24 shows the “long term” stability of the settling charac-
teristics of the AD841 output after a 10 V step. There is no evi-
dence of settling tails after the initial transient recovery time.
The use of a junction isolated process, together with careful lay-
out, avoids these problems by minimizing the effects of transis-
tor isolation capacitance discharge and thermally induced shifts
in circuit operating points. These problems do not occur even
under high output current conditions.
Applying the AD841
REV. B
–7–
Figure 24. AD841 Settling Demonstrating No Settling
Tails
GROUNDING AND BYPASSING
In designing practical circuits with the AD841, the user must
remember that whenever high frequencies are involved, some
special precautions are in order. Circuits must be built with
short interconnect leads. Large ground planes should be used
whenever possible to provide a low resistance, low inductance
circuit path, as well as minimizing the effects of high frequency
coupling. Sockets should be avoided because the increased
interlead capacitance can degrade bandwidth.
Feedback resistors should be of low enough value to assure that
the time constant formed with the circuit capacitances will not
limit the amplifier performance. Resistor values of less than
5 k
are recommended. If a larger resistor must be used, a
small (<10 pF) feedback capacitor in parallel with the feedback
resistor, R
F
, may be used to compensate for these stray capaci-
tances and optimize the dynamic performance of the amplifier
in the particular application.
Power supply leads should be bypassed to ground as close as
possible to the amplifier pins. A 2.2
μ
F capacitor in parallel
with a 0.1
μ
F ceramic disk capacitor is recommended.
CAPACITIVE LOAD DRIVING ABILITY
Like all wideband amplifiers, the AD841 is sensitive to capaci-
tive loading. The AD841 is designed to drive capacitive loads of
up to 20 pF without degradation of its rated performance. Ca-
pacitive loads of greater than 20 pF will decrease the dynamic
performance of the part although instability should not occur
unless the load exceeds 100 pF (for a unity-gain follower). A
resistor in series with the output can be used to decouple larger
capacitive loads.
Figure 25 shows a typical configuration for driving a large ca-
pacitive load. The 51
output resistor effectively isolates the
high frequency feedback from the load and stabilizes the circuit.
Low frequency feedback is returned to the amplifier summing
junction via the low pass filter formed by the 51
resistor and
the load capacitance, C
L
.
相关PDF资料 |
PDF描述 |
|---|---|
| AD847A | High Speed, Low Power Monolithic Op Amp |
| AD847J | High Speed, Low Power Monolithic Op Amp |
| AD847S | High Speed, Low Power Monolithic Op Amp |
| AD8509ARU | 9- and 11-Channel, Muxed Input LCD Reference Drivers |
| AD8509ARU-REEL | 9- and 11-Channel, Muxed Input LCD Reference Drivers |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD841SCHIPS | 制造商:AD 制造商全称:Analog Devices 功能描述:Wideband, Unity-Gain Stable, Fast Settling Op Amp |
| AD841SE | 功能描述:IC OPAMP GP 40MHZ 50MA 20CLCC RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:- 放大器类型:J-FET 电路数:2 输出类型:- 转换速率:3.5 V/µs 增益带宽积:1MHz -3db带宽:- 电流 - 输入偏压:30pA 电压 - 输入偏移:2000µV 电流 - 电源:200µA 电流 - 输出 / 通道:- 电压 - 电源，单路/双路(±):7 V ~ 36 V，±3.5 V ~ 18 V 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:8-DIP（0.300"，7.62mm） 供应商设备封装:8-PDIP 包装:管件 |
| AD841SE/883B | 功能描述:高速运算放大器 FAST SETTLING H.S. OP AMP RoHS:否 制造商:Texas Instruments 通道数量:1 电压增益 dB:116 dB 输入补偿电压:0.5 mV 转换速度:55 V/us 工作电源电压:36 V 电源电流:7.5 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube 产品: |
| AD841SEZ | 制造商:Analog Devices 功能描述:OP Amp Single GP ±18V 20-Pin LCC |
| AD841SH | 制造商:Analog Devices 功能描述:OP Amp Single GP 制造商:Rochester Electronics LLC 功能描述:FAST SETTLING H.S. OP AMP - Bulk |
发布紧急采购，3分钟左右您将得到回复。