- 您现在的位置：买卖IC网 > PDF目录8533 > AD8421BRMZ-RL (Analog Devices Inc)IC OPAMP INST 10MHZ LP LN 8MSOP PDF资料下载
参数资料
| 型号： | AD8421BRMZ-RL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 16/28页 |
| 文件大小： | 0K |
| 描述： | IC OPAMP INST 10MHZ LP LN 8MSOP |
| 标准包装： | 3,000 |
| 放大器类型： | 仪表 |
| 电路数： | 1 |
| 转换速率： | 35 V/µs |
| -3db带宽： | 10MHz |
| 电流 - 输入偏压： | 100pA |
| 电压 - 输入偏移： | 25µV |
| 电流 - 电源： | 2mA |
| 电流 - 输出 / 通道： | 65mA |
| 电压 - 电源，单路/双路(±)： | 5 V ~ 36 V，±2.5 V ~ 18 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-MSOP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
Data Sheet
AD8421
Rev. 0 | Page 23 of 28
a current of 40 mA at room temperature for at least a day. This
time is cumulative over the life of the device. If long periods of
overvoltage are expected, the use of an external protection method
is recommended. Under extreme input conditions, the output
of the amplifier may invert.
RADIO FREQUENCY INTERFERENCE (RFI)
RF rectification is often a problem when amplifiers are used in
applications that have strong RF signals. The problem is intensified
if long leads or PCB traces are required to connect the amplifier
to the signal source. The disturbance can appear as a dc offset
voltage or a train of pulses.
High frequency signals can be filtered with a low-pass filter
network at the input of the instrumentation amplifier, as shown
in Figure 68.
R
AD8421
+VS
+IN
–IN
0.1F
10F
0.1F
REF
VOUT
–VS
CD
10nF
CC
1nF
CC
1nF
33
1
012
3-
067
L*
*CHIP FERRITE BEAD.
Figure 68. RFI Suppression
The choice of resistor and capacitor values depends on the
desired trade-off between noise, input impedance at high
frequencies, CMRR, signal bandwidth, and RFI immunity. An
RC network limits both the differential and common-mode
bandwidth, as shown in the following equations:
)
2
(
π
2
1
C
D
DIFF
C
R
uency
FilterFreq
+
=
C
CM
RC
uency
FilterFreq
π
2
1
=
where CD ≥ 10 CC.
CD affects the differential signal, and CC affects the common-
mode signal. A mismatch between R × CC at the positive input
and R × CC at the negative input degrades the CMRR of the
larger than CC, the effect of the mismatch is reduced and CMRR
performance is improved near the cutoff frequencies.
To achieve low noise and sufficient RFI filtering, the use of chip
ferrite beads is recommended. Ferrite beads increase their impe-
dance with frequency, thus leaving the signal of interest unaffected
while preventing RF interference to reach the amplifier. They also
help to eliminate the need for large resistor values in the filter,
thus minimizing the system’s input-referred noise. The selection
of the appropriate ferrite bead and capacitor values is a function
of the interference frequency, input lead length, and RF power.
For best results, place the RFI filter network as close as possible
to the amplifier. Layout is critical to ensure that RF signals are
not picked up on the traces after the filter. If RF interference is
too strong to be filtered sufficiently, shielding is recommended.
The resistors used for the RFI filter can be the same as those used
for input protection.
CALCULATING THE NOISE OF THE INPUT STAGE
The total noise of the amplifier front end depends on much more
than the 3.2 nV/√Hz specification of this data sheet. The three
main contributors to noise are: the source resistance, the voltage
noise of the instrumentation amplifier, and the current noise of
the instrumentation amplifier.
In the following calculations, noise is referred to the input (RTI).
In other words, all sources of noise are calculated as if the source
appeared at the amplifier input. To calculate the noise referred
to the amplifier output (RTO), multiply the RTI noise by the
gain of the instru-mentation amplifier.
Source Resistance Noise
Any sensor connected to the AD8421 has some output resistance.
There may also be resistance placed in series with inputs for pro-
tection from either overvoltage or radio frequency interference.
This combined resistance is labeled R1 and R2 in Figure 69. Any
resistor, no matter how well made, has an intrinsic level of noise.
This noise is proportional to the square root of the resistor value.
At room temperature, the value is approximately equal to
4 nV/√Hz × √(resistor value in kΩ).
R2
RG
R1
SENSOR
AD8421
1
012
3-
0
65
Figure 69. Source Resistance from Sensor and Protection Resistors
For example, assume that the combined sensor and protection
resistance is 4 kΩ on the positive input and 1 kΩ on the negative
input. Then the total noise from the input resistance is
(
) (
)
=
+
=
×
+
×
16
64
1
4
2
8.9 nV/√Hz
相关PDF资料 |
PDF描述 |
|---|---|
| 2-1877846-0 | PLUG 6POS 0 DEG GRY/RED 4.0-5.2 |
| AD813ARZ-14-REEL | IC OPAMP TRIPLE VIDEO LP 14SOIC |
| VI-J0D-MZ-B1 | CONVERTER MOD DC/DC 85V 25W |
| VI-B3K-MU-F3 | CONVERTER MOD DC/DC 40V 200W |
| AD830JRZ | IC VIDEO DIFF AMP HS 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD8421BRZ | 功能描述:IC OP AMP INSTRUMENTATION 8SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:1 系列:- 放大器类型:通用 电路数:4 输出类型:满摆幅 转换速率:0.028 V/µs 增益带宽积:105kHz -3db带宽:- 电流 - 输入偏压:3nA 电压 - 输入偏移:100µV 电流 - 电源:3.3µA 电流 - 输出 / 通道:12mA 电压 - 电源，单路/双路(±):2.7 V ~ 12 V，±1.35 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:14-TSSOP 包装:剪切带 (CT) 其它名称:OP481GRUZ-REELCT |
| AD8421BRZ_PROMO | 制造商:Analog Devices 功能描述:IC INST AMP 35VIN 10MHZ S |
| AD8421BRZ-R7 | 功能描述:IC OPAMP INST 10MHZ LP LN 8MSOP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:1 系列:- 放大器类型:通用 电路数:2 输出类型:满摆幅 转换速率:2.1 V/µs 增益带宽积:3MHz -3db带宽:- 电流 - 输入偏压:1pA 电压 - 输入偏移:2000µV 电流 - 电源:750µA 电流 - 输出 / 通道:16mA 电压 - 电源，单路/双路(±):2.7 V ~ 16 V，±1.35 V ~ 8 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SOIC 包装:剪切带 (CT) 其它名称:296-10529-1 |
| AD8421BRZ-RL | 功能描述:IC OPAMP INST 10MHZ LP LN 8MSOP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:1 系列:- 放大器类型:通用 电路数:2 输出类型:满摆幅 转换速率:2.1 V/µs 增益带宽积:3MHz -3db带宽:- 电流 - 输入偏压:1pA 电压 - 输入偏移:2000µV 电流 - 电源:750µA 电流 - 输出 / 通道:16mA 电压 - 电源，单路/双路(±):2.7 V ~ 16 V，±1.35 V ~ 8 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SOIC 包装:剪切带 (CT) 其它名称:296-10529-1 |
| AD8421TRMZ-EP | 制造商:Analog Devices 功能描述:3NV/VHZNOISEPRECISIONINAMP - Rail/Tube 制造商:Analog Devices 功能描述:IC OPAMP INSTR 10MHZ 8MSOP 制造商:Analog Devices 功能描述:3nV/vHz noise Precision InAmp |
发布紧急采购，3分钟左右您将得到回复。