- 您现在的位置：买卖IC网 > PDF目录22177 > AD8436BCPZ-RL (Analog Devices Inc)IC CONV TRUE RMS-DC LP 20LFCSP PDF资料下载
参数资料
| 型号： | AD8436BCPZ-RL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 11/24页 |
| 文件大小： | 0K |
| 描述： | IC CONV TRUE RMS-DC LP 20LFCSP |
| 产品培训模块： | Introduction to Analog RMS-to-DC Technology: Converters and Applications |
| 标准包装： | 5,000 |
| 电流 - 电源： | 325µA |
| 电源电压： | ±2.4 V ~ 18 V，4.8 V ~ 36 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-WFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 20-LFCSP-WQ（4x4） |
| 包装： | 带卷 (TR) |
Data Sheet
The 16 kΩ resistor in the output converts the output current to
a dc voltage that can be connected to the output buffer or to the
circuit that follows. The output appears as a voltage source in
series with 16 kΩ. If a current output is desired, the resistor
connection to ground is left open and the output current is
applied to a subsequent circuit, such as the summing node of
a current summing amplifier. Thus, the core has both current
and voltage outputs, depending on the configuration. For a
voltage output with 0 Ω source impedance, use the output
buffer. The offset voltage of the buffer is 25 μV or 50 μV,
depending on the grade.
FET Input Buffer
Because the V-to-I input resistor value of the AD8436 rms core
is 8 k?, a high input impedance buffer is often used between
rms-dc converters and finite impedance sources. The optional
JFET input op amp minimizes attenuation and uncouples
common input amenities, such as resistive voltage dividers or
resistors used to terminate current transformers. The wide
bandwidth of the FET buffer is well matched to the rms core
bandwidth so that no information is lost due to serial band-
width effects. Although the input buffer consumes little current,
the buffer supply is independently accessible and can be
disconnected to reduce power.
Optional matched 10 k? input and feedback resistors are provided
on chip. Consult the Applications Information section to learn
AD8436
The output buffer can be configured as a single or two-pole low-
pass filter using circuits shown in the Applications Information
section. Residual output ripple is reduced, without affecting the
converted dc output. As the response approaches the low
frequency end of the bandwidth, the ripple rises, dependent on
the value of the averaging capacitor. Figure 27 shows the effects of
four combinations of averaging and filter capacitors. Although
the filter capacitor reduces the ripple for any given frequency, the
dc error is unaffected. Of course, a larger value averaging
capacitor can be selected, at a larger cost. The advantage of using
a low-pass filter is that a small value of filter capacitor, in
conjunction with the 16 k? output resistor, reduces ripple and
permits a smaller averaging capacitor, effecting a cost savings.
The recommended capacitor values for operation to 40 Hz are
10 μF for averaging and 3.3 μF for filter.
Dynamic Range
The AD8436 is a translinear rms-to-dc converter with exceptional
dynamic range. Although accuracy varies slightly more at the
extreme input values, the device still converts with no spurious
noise or dropout. Figure 25 is a plot of the rms/dc transfer function
near zero voltage. Unlike processor or other solutions, residual
errors at very low input levels can be disregarded for most
applications.
30
how these resistors can be used. The 3 dB bandwidth of the input
buffer is 2.7 MHz at 10 mV rms input and approximately 1.5 MHz
at 1 V rms. The amplifier gain and bandwidth are sufficient for
applications requiring modest gain or response enhancement to
a few hundred kilohertz (kHz), if desired. Configurations of the
input buffer are discussed in the Applications Information
section.
20
10
0
AD8436
SOLUTION
ΔΣ OR OTHER DIGITAL
SOLUTIONS CANNOT
WORK AT ZERO
VOLTS
Precision Output Buffer
–30
–20
–10 0 10
INPUT VOLTAGE (mV DC)
20
30
The precision output buffer is a bipolar input amplifier, laser
trimmed to cancel input offset voltage errors. As with the input
buffer, the supply current is very low (<50 μA, typically), and the
power can be disconnected for power savings if the buffer is not
needed. Be sure that the noninverting input is also disconnected
from the core output (OUT) if the buffer supply pin is discon-
nected. Although the input current of the buffer is very low,
a laser-trimmed 16 kΩ resistor, connected in series with the
inverting input, offsets any self-bias offset voltage.
Rev. B | Page 11 of 24
Figure 25. DC Transfer Function near Zero
相关PDF资料 |
PDF描述 |
|---|---|
| V110A48C300B | CONVERTER MOD DC/DC 48V 300W |
| ESM08DSUS | CONN EDGECARD 16POS DIP .156 SLD |
| PMLL4148L,135 | DIODE HIGH SPEED SW 75V SOD80C |
| AD8436BCPZ-R7 | IC CONV TRUE RMS-DC LP 20LFCSP |
| PMLL4148L,115 | DIODE SW GPP 75V 200MA SOD80C |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD8436BCPZ-WP | 功能描述:IC CONV TRUE RMS-DC LP 20LFCSP RoHS:是 类别:集成电路 (IC) >> PMIC - RMS 至 DC 转换器 系列:- 标准包装:46 系列:- 电流 - 电源:1.2mA 电源电压:±18 V，36 V 安装类型:表面贴装 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 供应商设备封装:16-SOIC W 包装:管件 |
| AD8436BRQZ | 功能描述:其他电源管理 Low PowerTrue RMS-to-DC Converter RoHS:否 制造商:Texas Instruments 输出电压范围: 输出电流:4 mA 输入电压范围:3 V to 3.6 V 输入电流: 功率耗散: 工作温度范围:- 40 C to + 110 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-48 封装:Reel |
| AD8436BRQZ_PROMO | 制造商:Analog Devices 功能描述:IC RMS TO DC CONV 0.5% QSOP |
| AD8436BRQZ-R7 | 功能描述:其他电源管理 Low PowerTrue RMS-to-DC Converter RoHS:否 制造商:Texas Instruments 输出电压范围: 输出电流:4 mA 输入电压范围:3 V to 3.6 V 输入电流: 功率耗散: 工作温度范围:- 40 C to + 110 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-48 封装:Reel |
| AD8436BRQZ-RL | 功能描述:其他电源管理 Low PowerTrue RMS-to-DC Converter RoHS:否 制造商:Texas Instruments 输出电压范围: 输出电流:4 mA 输入电压范围:3 V to 3.6 V 输入电流: 功率耗散: 工作温度范围:- 40 C to + 110 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-48 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。