参数资料
| 型号： | AD8541ARTZ-R2 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 6/20页 |
| 文件大小： | 0K |
| 描述： | IC OPAMP GP R-R CMOS SOT23-5 |
| 设计资源： | Logarithmic Audio Volume Control with Glitch Reduction Using AD5292 (CN0120) |
| 标准包装： | 250 |
| 放大器类型： | 通用 |
| 电路数： | 1 |
| 输出类型： | 满摆幅 |
| 转换速率： | 0.92 V/µs |
| 增益带宽积： | 1MHz |
| 电流 - 输入偏压： | 4pA |
| 电压 - 输入偏移： | 1000µV |
| 电流 - 电源： | 45µA |
| 电流 - 输出 / 通道： | 30mA |
| 电压 - 电源，单路/双路(±)： | 2.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SC-74A，SOT-753 |
| 供应商设备封装： | SOT-23-5 |
| 包装： | 带卷 (TR) |
AD8541/AD8542/AD8544
Rev. G | Page 14 of 20
APPLICATIONS
NOTCH FILTER
The AD854x have very high open-loop gain (especially with a
supply voltage below 4 V), which makes it useful for active filters of
all types. For example, Figure 36 illustrates the AD8542 in the
classic twin-T notch filter design. The twin-T notch is desired
for simplicity, low output impedance, and minimal use of op
amps. In fact, this notch filter can be designed with only one op
amp if Q adjustment is not required. Simply remove U2 as
illustrated in Figure 37. However, a major drawback to this
circuit topology is ensuring that all the Rs and Cs closely match.
The components must closely match or notch frequency offset
and drift causes the circuit to no longer attenuate at the ideal
notch frequency. To achieve desired performance, 1% or better
component tolerances or special component screens are usually
required. One method to desensitize the circuit-to-component
mismatch is to increase R2 with respect to R1, which lowers Q.
A lower Q increases attenuation over a wider frequency range
but reduces attenuation at the peak notch frequency.
1/2 AD8542
5
6
7
8
3
2
4
1
1/2 AD8542
5.0V
U1
VOUT
U2
R2
2.5k
R1
97.5k
2.5VREF
C
26.7nF
C
26.7nF
2.5VREF
R/2
50k
R
100k
R
100k
2C
53.6F
f0 =
1
2πRC
1
R1
R1 + R2
4 1 –
0
093
5-
03
5
VIN
Figure 36. 60 Hz Twin-T Notch Filter, Q = 10
C
2C
R/2
RR
7
3
2
4
6
AD8541
5.0V
C
VOUT
2.5VREF
VIN
009
35
-0
36
U1
Figure 37. 60 Hz Twin-T Notch Filter, Q = ∞ (Ideal)
Figure 38 is an example of the AD8544 in a notch filter circuit. The
frequency dependent negative resistance (FDNR) notch filter has
fewer critical matching requirements than the twin-T notch, where
as the Q of the FDNR is directly proportional to a single resistor R1.
Although matching component values is still important, it is also
much easier and/or less expensive to accomplish in the FDNR
circuit. For example, the twin-T notch uses three capacitors
with two unique values, whereas the FDNR circuit uses only
two capacitors, which may be of the same value. U3 is simply a
buffer that is added to lower the output impedance of the circuit.
4
1/4 AD8544
11
6
1/4 AD8544
10
8
9
2
1
3
1/4 AD8544
12
14
13
5
7
U3
U1
U4
U2
C2
1F
C1
1F
R1
Q ADJUST
200
R
2.61k
R
2.61k
R
2.61k
R
2.61k
VOUT
2.5VREF
NC
f =
1
2π LC1
L = R2C2
00
93
5-
0
37
VIN
Figure 38. FDNR 60 Hz Notch Filter with Output Buffer
COMPARATOR FUNCTION
A comparator function is a common application for a spare op
amp in a quad package. Figure 39 illustrates of the AD8544 as a
comparator in a standard overload detection application. Unlike
many op amps, the AD854x family can double as comparators
because this op amp family has a rail-to-rail differential input
range, rail-to-rail output, and a great speed vs. power ratio.
R2 is used to introduce hysteresis. The AD854x, when used as
comparators, have 5 μs propagation delay at 5 V and 5 μs
overload recovery time.
1/4 AD8541
R1
1k
VOUT
2.5VREF
VIN
R2
1M
2.5VDC
00
935
-0
38
Figure 39. AD854x Comparator Application—Overload Detector
相关PDF资料 |
PDF描述 |
|---|---|
| SMBJ120CA-13 | TVS BI-DIR 120V 600W SMB |
| SMAJ90CA-13 | TVS BI-DIR 90V 400W SMA |
| SMAJ90A-13 | TVS UNI-DIR 90V 400W SMA |
| TA45-A126L100C0 | CIRCUIT BRKR ROCKR ILL 10A 2P QC |
| SMAJ100CA-13 | TVS BI-DIR 100V 400W SMA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD8541ARTZ-R2 | 制造商:Analog Devices 功能描述:IC, OP-AMP, 1MHZ, 0.92V/ us, SOT-23-5 |
| AD8541ARTZ-REEL | 功能描述:IC OPAMP GP R-R CMOS SOT23-5 RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:160 系列:- 放大器类型:通用 电路数:4 输出类型:满摆幅 转换速率:10 V/µs 增益带宽积:9MHz -3db带宽:- 电流 - 输入偏压:1pA 电压 - 输入偏移:250µV 电流 - 电源:730µA 电流 - 输出 / 通道:28mA 电压 - 电源，单路/双路(±):2.7 V ~ 5.5 V，±1.35 V ~ 2.75 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC N 包装:管件 |
| AD8541ARTZ-REEL7 | 功能描述:IC OPAMP GP R-R CMOS SOT23-5 RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 特色产品:CMOS Operational Amplifier 标准包装:2,500 系列:- 放大器类型:通用 电路数:2 输出类型:满摆幅 转换速率:1 V/µs 增益带宽积:1MHz -3db带宽:- 电流 - 输入偏压:1pA 电压 - 输入偏移:1000µV 电流 - 电源:900µA 电流 - 输出 / 通道:1mA 电压 - 电源，单路/双路(±):5 V ~ 14.5 V，±2.5 V ~ 7.25 V 工作温度:-40°C ~ 105°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.173"，4.40mm 宽） 供应商设备封装:8-SOP 包装:带卷 (TR) 产品目录页面:1372 (CN2011-ZH PDF) 其它名称:BD7562SF-E2TR |
| AD8541ARZ | 功能描述:IC OPAMP GP R-R CMOS 1MHZ 8SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 产品培训模块:Differential Circuit Design Techniques for Communication Applications 标准包装:1 系列:- 放大器类型:RF/IF 差分 电路数:1 输出类型:差分 转换速率:9800 V/µs 增益带宽积:- -3db带宽:2.9GHz 电流 - 输入偏压:3µA 电压 - 输入偏移:- 电流 - 电源:40mA 电流 - 输出 / 通道:- 电压 - 电源，单路/双路(±):3 V ~ 3.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-VQFN 裸露焊盘，CSP 供应商设备封装:16-LFCSP-VQ 包装:剪切带 (CT) 产品目录页面:551 (CN2011-ZH PDF) 其它名称:ADL5561ACPZ-R7CT |
| AD8541ARZ1 | 制造商:AD 制造商全称:Analog Devices 功能描述:General-Purpose CMOS Rail-to-Rail Amplifiers |
发布紧急采购，3分钟左右您将得到回复。