- 您现在的位置：买卖IC网 > PDF目录6069 > AD8556ACPZ-REEL7 (Analog Devices Inc)IC AMP CHOPPER 2MHZ 10MA 16LFCSP PDF资料下载
参数资料
| 型号： | AD8556ACPZ-REEL7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 10/28页 |
| 文件大小： | 0K |
| 描述： | IC AMP CHOPPER 2MHZ 10MA 16LFCSP |
| 标准包装： | 1 |
| 系列： | DigiTrim® |
| 放大器类型： | 断路器（零漂移） |
| 电路数： | 1 |
| 转换速率： | 1.2 V/µs |
| 增益带宽积： | 2MHz |
| 电流 - 输入偏压： | 49nA |
| 电压 - 输入偏移： | 2µV |
| 电流 - 电源： | 2mA |
| 电流 - 输出 / 通道： | 10mA |
| 电压 - 电源，单路/双路(±)： | 4.5 V ~ 5.5 V |
| 工作温度： | -40°C ~ 140°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-VQFN 裸露焊盘，CSP |
| 供应商设备封装： | 16-LFCSP-VQ |
| 包装： | 标准包装 |
| 产品目录页面： | 771 (CN2011-ZH PDF) |
| 其它名称： | AD8556ACPZ-REEL7DKR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
AD8556
Rev. A | Page 18 of 28
OPEN WIRE FAULT DETECTION
The inputs to A1 and A2, VNEG and VPOS, each have a com-
parator to detect whether VNEG or VPOS exceeds a threshold
voltage, nominally VDD 2.0 V. If (VNEG > VDD 2.0 V) or
(VPOS > VDD 2.0 V), VOUT is clamped to VSS. The output
current limit circuit is disabled in this mode, but the maximum
sink current is approximately 10 mA when VDD = 5 V. The inputs
to A1 and A2, VNEG and VPOS, are also pulled up to VDD by
currents IP1 and IP2. These are both nominally 49 nA and
matched to within 3 nA. If the inputs to A1 or A2 are accidentally
left floating, as with an open wire fault, IP1 and IP2 pull them
to VDD, which would cause VOUT to swing to VSS, allowing
this fault to be detected. It is not possible to disable IP1 and IP2,
nor the clamping of VOUT to VSS, when VNEG or VPOS
approaches VDD.
SHORTED WIRE FAULT DETECTION
The AD8556 provides fault detection when VPOS, VNEG, or
VCLAMP shorts to VDD and VSS. Figure 48 shows the voltage
regions at VPOS, VNEG, and VCLAMP that trigger an error
condition. When an error condition occurs, the VOUT pin is
VPOS
VNEG
VSS
VINL
VINH
VDD
VSS
VCLL
VDD
VCLAMP
VSS
VINL
VINH
VDD
ERROR
NORMAL
ERROR
NORMAL
ERROR
NORMAL
05
44
8
-04
8
Figure 48. Voltage Regions at VPOS, VNEG, and VCLAMP
that Trigger a Fault Condition
Table 7. Typical VINL, VINH, and VCLL Values (VDD = 5 V)
Voltage
Min (V)
Typ (V)
Max (V)
VOUT Condition
VINH
2.95
3.0
3.05
Short to VSS fault
detection
VINL
1.95
2.0
2.05
Short to VSS fault
detection
VCLL
1.05
1.1
1.15
Short to VSS fault
detection
FLOATING VPOS, VNEG, OR VCLAMP FAULT
DETECTION
A floating fault condition at the VPOS, VNEG, or VCLAMP
pins is detected by using a low current to pull a floating input
into an error voltage range, defined in the Shorted Wire Fault
Detection section. In this way, the VOUT pin is shorted to VSS
when a floating input is detected. Table 8 lists the currents used.
Table 8. Floating Fault Detection at VPOS, VNEG, and
VCLAMP
Mnemonic
Typical Current
Goal of Current
VPOS
49 nA pull-up
Pull VPOS above VINH
VNEG
49 nA pull-up
Pull VNEG above VINH
VCLAMP
0.2 μA pull-down
Pull VCLAMP below VCLL
DEVICE PROGRAMMING
Digital Interface
The digital interface allows the first stage gain, second stage
gain, and output offset to be adjusted and allows desired values
for these parameters to be permanently stored by selectively
blowing polysilicon fuses. To minimize pin count and board
space, a single-wire digital interface is used. The digital input pin,
DIGIN, has hysteresis to minimize the possibility of inadvertent
triggering with slow signals. It also has a pull-down current sink
to allow it to be left floating when programming is not being
performed. The pull-down ensures inactive status of the digital
input by forcing a dc low voltage on DIGIN.
A short pulse at DIGIN from low to high and back to low again,
such as between 50 ns and 10 μs long, loads 0 into the shift register.
A long pulse at DIGIN, such as 50 μs or longer, loads 1 into the
shift register. The time between pulses should be at least 10 μs.
Assuming VSS = 0 V, voltages at DIGIN between VSS and 0.2 ×
VDD are recognized as a low, and voltages at DIGIN between
0.8 × VDD and VDD are recognized as a high. The timing
diagram example in Figure 49 shows the waveform for entering
code 010011 into the shift register.
相关PDF资料 |
PDF描述 |
|---|---|
| GB0504AFV1-8 | BLOWER 5VDC 40 X 40 X 9.3MM |
| RMCF2512FT2R00 | RES TF 2 OHM 1% 1W 2512 |
| 151210-2420-RB-WC | CONN 10POS 2MM HEADER DL STR SMD |
| 0316005.NRT1 | FUSE PICO 5A 125V FAST CCC AXL |
| GB1205PKV1-8AY | BLOWER 12VDC 50 X 50 X 20MM |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD8556ARZ | 功能描述:IC AMP CHOPPER 2MHZ 10MA 8SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:DigiTrim® 标准包装:2,500 系列:- 放大器类型:通用 电路数:4 输出类型:- 转换速率:0.6 V/µs 增益带宽积:1MHz -3db带宽:- 电流 - 输入偏压:45nA 电压 - 输入偏移:2000µV 电流 - 电源:1.4mA 电流 - 输出 / 通道:40mA 电压 - 电源，单路/双路(±):3 V ~ 32 V，±1.5 V ~ 16 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:14-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:14-TSSOP 包装:带卷 (TR) 其它名称:LM324ADTBR2G-NDLM324ADTBR2GOSTR |
| AD8556ARZ-REEL | 功能描述:IC AMP CHOPPER 2MHZ 10MA 8SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:DigiTrim® 标准包装:73 系列:Over-The-Top® 放大器类型:通用 电路数:4 输出类型:满摆幅 转换速率:0.07 V/µs 增益带宽积:200kHz -3db带宽:- 电流 - 输入偏压:1nA 电压 - 输入偏移:285µV 电流 - 电源:50µA 电流 - 输出 / 通道:25mA 电压 - 电源，单路/双路(±):2 V ~ 44 V，±1 V ~ 22 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-WFDFN 裸露焊盘 供应商设备封装:16-DFN-EP（5x3） 包装:管件 |
| AD8556ARZ-REEL7 | 功能描述:IC AMP CHOPPER 2MHZ 10MA 8SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:DigiTrim® 标准包装:73 系列:Over-The-Top® 放大器类型:通用 电路数:4 输出类型:满摆幅 转换速率:0.07 V/µs 增益带宽积:200kHz -3db带宽:- 电流 - 输入偏压:1nA 电压 - 输入偏移:285µV 电流 - 电源:50µA 电流 - 输出 / 通道:25mA 电压 - 电源，单路/双路(±):2 V ~ 44 V，±1 V ~ 22 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-WFDFN 裸露焊盘 供应商设备封装:16-DFN-EP（5x3） 包装:管件 |
| AD8556CP-EBZ | 功能描述:AD8556 DigiTrim? Series 1 - Single Channels per IC Chopper (Zero-Drift) Amplifier Evaluation Board 制造商:analog devices inc. 系列:DigiTrim? 零件状态:有效 每 IC 通道数:1 - 单 放大器类型:断路器（零漂移） 输出类型:单端 压摆率:1.2 V/μs -3db 带宽:- 电流 - 输出/通道:10mA 工作温度:-40°C ~ 140°C 电流 - 电源（主 IC）:2mA 电压 - 电源，单/双（±）:4.5 V ~ 5.5 V 板类型:完全填充 所含物品:板 使用的 IC/零件:AD8556 标准包装:1 |
| AD8556-EVALZ | 制造商:Analog Devices 功能描述:EVALUATION BOARD - Boxed Product (Development Kits) |
发布紧急采购，3分钟左右您将得到回复。