- 您现在的位置：买卖IC网 > PDF目录5884 > AD8556ARZ-REEL7 (Analog Devices Inc)IC AMP CHOPPER 2MHZ 10MA 8SOIC PDF资料下载
参数资料
| 型号： | AD8556ARZ-REEL7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 16/28页 |
| 文件大小： | 0K |
| 描述： | IC AMP CHOPPER 2MHZ 10MA 8SOIC |
| 标准包装： | 1,000 |
| 系列： | DigiTrim® |
| 放大器类型： | 断路器（零漂移） |
| 电路数： | 1 |
| 转换速率： | 1.2 V/µs |
| 增益带宽积： | 2MHz |
| 电流 - 输入偏压： | 49nA |
| 电压 - 输入偏移： | 2µV |
| 电流 - 电源： | 2mA |
| 电流 - 输出 / 通道： | 10mA |
| 电压 - 电源，单路/双路(±)： | 4.5 V ~ 5.5 V |
| 工作温度： | -40°C ~ 140°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SO |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
AD8556
Rev. A | Page 23 of 28
Important:
Once a programming attempt is made for any
fuse, there should be no further attempt to blow that fuse.
If a fuse does not program to the expected state, discard
the unit. The expected incidence rate of attempted but
unblown fuses is very small when following the proper
programming procedure and conditions.
3.
Set VSS to 0 V and VDD to 5.25 V (±0.25 V). Power
supplies should be capable of supplying 250 mA at the
required voltage and properly bypassed as described
in the Programming Mode section. Use program mode to
permanently enter the desired codes for the first stage gain,
second stage gain, and output offset. Blow the parity bit
fuse if necessary (see Parity Error Detection section). Blow
the master fuse to allow the AD8556 to read data from the
fuses and to prevent further programming.
4.
Set VDD and VSS to the desired values in the application.
Use read mode with low sense current followed by high
sense current to verify programmed codes.
5.
Measure gain and offset to verify correct functionality.
Determining Optimal Gain and Offset Codes
First, determine the desired gain:
1.
Determine the desired gain, GA (using the measurements
obtained from the simulation).
2.
that (4.00 × 1.04) < (GA/G2) < (6.4/1.04). This ensures the
first and last codes for the first stage gain are not used,
thereby allowing enough first stage gain codes within each
second stage gain range to adjust for the 3% accuracy.
Next, set the second stage gain:
1.
Use the simulation mode to set the second stage gain to G2.
2.
Set the output offset to allow the AD8556 gain to be
measured, for example, use Code 128 to set it to
midsupply.
3.
Use Table 5 or Equation 1 to set the first stage gain code
CG1, so the first stage gain is nominally GA/G2.
4.
Measure the resulting gain, GB. G
B
should be within
3% of GA.
5.
Calculate the first stage gain error (in relative terms)
EG1 = GB/G
B
A
1.
6.
Calculate the error (in the number of the first stage gain
codes) CEG1 = EG1/0.00370.
7.
Set the first stage gain code to CG1 CEG1.
8.
Measure the gain, GC. GC should be closer to GA than to GB.
B
9.
Calculate the error (in relative terms) EG2 = GC/GA 1.
10. Calculate the error (in the number of the first stage gain
codes) CEG2 = EG2/0.00370.
11. Set the first stage gain code to CG1 CEG1 CEG2. The
resulting gain should be within one code of GA.
Finally, determine the desired output offset:
1.
Determine the desired output offset OA (using the
measurements obtained from the simulation).
2.
Use Equation 2 to set the output offset code CO1 such that
the output offset is nominally OA.
3.
Measure the output offset, OB. O
B
should be within
3% of OA.
4.
Calculate the error (in relative terms) EO1 = OB/O
B
A
1.
5.
Calculate the error (in the number of the output offset
codes) CEO1 = EO1/0.00392.
6.
Set the output offset code to CO1 CEO1.
7.
Measure the output offset, OC. OC should be closer to OA
than to OB.
B
8.
Calculate the error (in relative terms) EO2 = OC/OA 1.
9.
Calculate the error (in the number of the output offset
codes) CEO2 = EO2/0.00392.
10. Set the output offset code to CO1 CEO1 CEO2. The
resulting offset should be within one code of OA.
相关PDF资料 |
PDF描述 |
|---|---|
| GRPB022VWVN-RC | CONN HEADER .050" 4POS DL PCB AU |
| TSW-148-14-G-D | CONN HEADER 96POS .100" DL GOLD |
| TSW-148-08-G-D | CONN HEADER 96POS .100" DL GOLD |
| LTC2053CMS8-SYNC#PBF | IC INSTRUMNT AMP R-RIN/OUT 8MSOP |
| FTS-130-03-L-D | CONN HEADER 60POS DUAL .05" T/H |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD8556CP-EBZ | 功能描述:AD8556 DigiTrim? Series 1 - Single Channels per IC Chopper (Zero-Drift) Amplifier Evaluation Board 制造商:analog devices inc. 系列:DigiTrim? 零件状态:有效 每 IC 通道数:1 - 单 放大器类型:断路器（零漂移） 输出类型:单端 压摆率:1.2 V/μs -3db 带宽:- 电流 - 输出/通道:10mA 工作温度:-40°C ~ 140°C 电流 - 电源（主 IC）:2mA 电压 - 电源，单/双（±）:4.5 V ~ 5.5 V 板类型:完全填充 所含物品:板 使用的 IC/零件:AD8556 标准包装:1 |
| AD8556-EVALZ | 制造商:Analog Devices 功能描述:EVALUATION BOARD - Boxed Product (Development Kits) |
| AD8557 | 制造商:AD 制造商全称:Analog Devices 功能描述:Wide Supply Range, Micropower, |
| AD85571 | 制造商:AD 制造商全称:Analog Devices 功能描述:10 MHz, 20 V/レs, G = 1, 10, 100, 1000 i CMOS㈢ Programmable Gain Instrumentation Amplifier |
| AD8557ACPZ-R2 | 功能描述:IC AMP CHOPPER 2MHZ 55MA 16LFCSP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:DigiTrim® 标准包装:50 系列:- 放大器类型:J-FET 电路数:2 输出类型:- 转换速率:13 V/µs 增益带宽积:3MHz -3db带宽:- 电流 - 输入偏压:65pA 电压 - 输入偏移:3000µV 电流 - 电源:1.4mA 电流 - 输出 / 通道:- 电压 - 电源，单路/双路(±):7 V ~ 36 V，±3.5 V ~ 18 V 工作温度:-40°C ~ 85°C 安装类型:通孔 封装/外壳:8-DIP（0.300"，7.62mm） 供应商设备封装:8-PDIP 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。