参数资料
| 型号： | AD8628ART-R2 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 9/24页 |
| 文件大小： | 0K |
| 描述： | IC OPAMP CHOPPER R-R SOT23-5 |
| 设计资源： | Precision, Unipolar, Inverting Conversion Using AD5546/56 DAC (CN0022) Precision, Unipolar, Inverting Conversion Using AD5547/57 DAC (CN0026) Precision, Unipolar, Noninverting Configuration for the AD5547/57 DAC (CN0027) Precision, Unipolar, Noninverting Configuration for the AD5546/56 DAC (CN0023) High Precision Digital-to-Analog Conversion Using the 16-Bit AD5542/1, ADR421, and AD8628 (CN0079) |
| 标准包装： | 1 |
| 放大器类型： | 零漂移 |
| 电路数： | 1 |
| 输出类型： | 满摆幅 |
| 转换速率： | 1 V/µs |
| 增益带宽积： | 2.5MHz |
| -3db带宽： | 2.5MHz |
| 电流 - 输入偏压： | 30pA |
| 电压 - 输入偏移： | 1µV |
| 电流 - 电源： | 850µA |
| 电流 - 输出 / 通道： | 30mA |
| 电压 - 电源，单路/双路(±)： | 2.7 V ~ 5 V，±1.35 V ~ 2.5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SC-74A，SOT-753 |
| 供应商设备封装： | SOT-23-5 |
| 包装： | 标准包装 |
| 其它名称： | AD8628ART-R2DKR |
Data Sheet
AD8628/AD8629/AD8630
Rev. J | Page 17 of 24
INPUT OVERVOLTAGE PROTECTION
amplifiers, care should be taken to ensure that the potential
difference between the inputs does not exceed the supply voltage.
Under normal negative feedback operating conditions, the
amplifier corrects its output to ensure that the two inputs are at
the same voltage. However, if either input exceeds either supply
rail by more than 0.3 V, large currents begin to flow through the
ESD protection diodes in the amplifier.
These diodes are connected between the inputs and each supply
rail to protect the input transistors against an electrostatic discharge
event, and they are normally reverse-biased. However, if the input
voltage exceeds the supply voltage, these ESD diodes can become
forward-biased. Without current limiting, excessive amounts
of current could flow through these diodes, causing permanent
damage to the device. If inputs are subject to overvoltage,
appropriate series resistors should be inserted to limit the diode
current to less than 5 mA maximum.
OUTPUT PHASE REVERSAL
Output phase reversal occurs in some amplifiers when the input
common-mode voltage range is exceeded. As common-mode
voltage is moved outside the common-mode range, the outputs of
these amplifiers can suddenly jump in the opposite direction to
the supply rail. This is the result of the differential input pair
shutting down, causing a radical shifting of internal voltages
that results in the erratic output behavior.
designed to prevent any output phase reversal, provided that
both inputs are maintained within the supply voltages. If one or
both inputs could exceed either supply voltage, a resistor should
be placed in series with the input to limit the current to less than
5 mA. This ensures that the output does not reverse its phase.
OVERLOAD RECOVERY TIME
Many auto-zero amplifiers are plagued by a long overload recovery
time, often in ms, due to the complicated settling behavior of
the internal nulling loops after saturation of the outputs. The
settling occurs within two clock cycles after output saturation
occurs. This results in a much shorter recovery time, less
than 10 μs, when compared to other auto-zero amplifiers. The
performance when the parts are used to drive loads that inject
transients into the outputs. This is a common situation when an
amplifier is used to drive the input of switched capacitor ADCs.
TIME (500s/DIV)
VOL
T
A
G
E
(
V)
VOUT
0V
VIN
02
73
5-
0
53
CH1 = 50mV/DIV
CH2 = 1V/DIV
AV = –50
Figure 56. Positive Input Overload Recovery for the AD8628
TIME (500s/DIV)
VOL
T
A
G
E
(
V)
VOUT
0V
VIN
02
73
5-
0
54
CH1 = 50mV/DIV
CH2 = 1V/DIV
AV = –50
Figure 57. Positive Input Overload Recovery for Competitor A
TIME (500s/DIV)
VOL
T
A
G
E
(
V)
VOUT
0V
VIN
02
73
5-
0
55
CH1 = 50mV/DIV
CH2 = 1V/DIV
AV = –50
Figure 58. Positive Input Overload Recovery for Competitor B
相关PDF资料 |
PDF描述 |
|---|---|
| 0034.3121.PT | FUSE 2.5A 250V 5X20 T-LAG GLASS |
| 3413.0120.22 | FUSE 2.5A 32V FAST 1206 SMD |
| 8-320634-2 | TERM RING TONGUE 12-10AWG PIDG |
| MMA23-0071R1 | CONN RACK/PANEL 7POS 5A |
| TSW-147-23-L-D | CONN HEADER 94POS .100" DL GOLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD8628ART-REEL7 | 制造商:Analog Devices 功能描述:SP Amp Chopper Stabilization Single R-R I/O 制造商:Analog Devices 功能描述:IC OP-AMP SINGLE R/R |
| AD8628ARTZ | 制造商:Analog Devices 功能描述:OP AMP ZERO DRIFT R/R SOT23-5 制造商:Analog Devices 功能描述:OP AMP, ZERO DRIFT, R/R, SOT23-5 |
| AD8628ARTZ-R2 | 功能描述:IC OPAMP CHOPPER R-R SOT23-5 RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:- 放大器类型:通用 电路数:2 输出类型:满摆幅 转换速率:1.8 V/µs 增益带宽积:6.5MHz -3db带宽:4.5MHz 电流 - 输入偏压:5nA 电压 - 输入偏移:100µV 电流 - 电源:65µA 电流 - 输出 / 通道:35mA 电压 - 电源，单路/双路(±):1.8 V ~ 5.25 V，±0.9 V ~ 2.625 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| AD8628ARTZ-R2 | 制造商:Analog Devices 功能描述:IC, OP-AMP, 2.5MHZ, 1V/ us, SOT-23-5 |
| AD8628ARTZ-REEL7 | 功能描述:IC OPAMP CHOPPER R-R SOT23-5 RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 产品培训模块:Differential Circuit Design Techniques for Communication Applications 标准包装:1 系列:- 放大器类型:RF/IF 差分 电路数:1 输出类型:差分 转换速率:9800 V/µs 增益带宽积:- -3db带宽:2.9GHz 电流 - 输入偏压:3µA 电压 - 输入偏移:- 电流 - 电源:40mA 电流 - 输出 / 通道:- 电压 - 电源，单路/双路(±):3 V ~ 3.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-VQFN 裸露焊盘，CSP 供应商设备封装:16-LFCSP-VQ 包装:剪切带 (CT) 产品目录页面:551 (CN2011-ZH PDF) 其它名称:ADL5561ACPZ-R7CT |
发布紧急采购，3分钟左右您将得到回复。