- 您现在的位置：买卖IC网 > PDF目录373954 > AD8655 (Analog Devices, Inc.) Low Noise, Precision CMOS Amplifier PDF资料下载
参数资料
| 型号： | AD8655 |
| 厂商： | Analog Devices, Inc. |
| 英文描述： | Low Noise, Precision CMOS Amplifier |
| 中文描述： | 低噪声，高精度CMOS放大器 |
| 文件页数： | 16/20页 |
| 文件大小： | 273K |
| 代理商： | AD8655 |
AD8655/AD8656
APPLICATIONS
INPUT OVERVOLTAGE PROTECTION
The internal protective circuitry of the AD8655/AD8656 allows
voltages exceeding the supply to be applied at the input. It is
recommended, however, not to apply voltages that exceed the
supplies by more than 0.3 V at either input of the amplifier. If a
higher input voltage is applied, series resistors should be used to
limit the current flowing into the inputs. The input current
should be limited to less than 5 mA.
Rev. A | Page 16 of 20
One simple technique for compensation is a snubber that
consists of a simple RC network. With this circuit in place,
output swing is maintained, and the amplifier is stable at all
gains.
Figure 57 shows the implementation of a snubber, which
reduces overshoot by more than 30% and eliminates ringing.
Using a snubber does not recover the loss of bandwidth
incurred from a heavy capacitive load.
TIME (2
μ
s/DIV)
V
S
= ±2.5V
A
V
= 1
C
L
= 500pF
0
V
The extremely low input bias current allows the use of larger
resistors, which allows the user to apply higher voltages at the
inputs. The use of these resistors adds thermal noise, which
contributes to the overall output voltage noise of the amplifier.
For example, a 10 kΩ resistor has less than 12.6 nV/√Hz of
thermal noise and less than 10 nV of error voltage at room
temperature.
INPUT CAPACITANCE
Along with bypassing and ground, high speed amplifiers can be
sensitive to parasitic capacitance between the inputs and ground.
For circuits with resistive feedback network, the total capacitance,
whether it is the source capacitance, stray capacitance on the
input pin, or the input capacitance of the amplifier, causes a
breakpoint in the noise gain of the circuit. As a result, a
capacitor must be added in parallel with the gain resistor to
obtain stability. The noise gain is a function of frequency and
peaks at the higher frequencies, assuming the feedback capaci-
tor is selected to make the second-order system critically
damped. A few picofarads of capacitance at the input reduce
the input impedance at high frequencies, which increases the
amplifier’s gain, causing peaking in the frequency response or
oscillations. With the AD8655/AD8656, additional input
damping is required for stability with capacitive loads greater
than 200 pF with direct input to output feedback. See the
Driving Capacitive Loads section.
Figure 56. Driving Heavy Capacitive Loads Without Compensation
V+
200
Ω
500pF
500pF
V–
V
CC
V
EE
200mV
+
–
0
+
–
Figure 57. Snubber Network
V
S
= ±2.5V
A
V
= 1
R
S
= 200
Ω
C
S
= 500pF
C
L
= 500pF
TIME (10
μ
s/DIV)
0
V
DRIVING CAPACITIVE LOADS
Although the AD8655/AD8656 can drive capacitive loads up to
500 pF without oscillating, a large amount of ringing is present
when operating the part with input frequencies above 100 kHz.
This is especially true when the amplifiers are configured in
positive unity gain (worst case). When such large capacitive
loads are required, the use of external compensation is highly
recommended. This reduces the overshoot and minimizes
ringing, which, in turn, improves the stability of the
AD8655/AD8656 when driving large capacitive loads.
Figure 58. Driving Heavy Capacitive Loads Using a Snubber Network
相关PDF资料 |
PDF描述 |
|---|---|
| AD8655ARMZ-R2 | Low Noise, Precision CMOS Amplifier |
| AD8655ARMZ-REEL | Low Noise, Precision CMOS Amplifier |
| AD8661ACP | 16V Low Cost, High Performance CMOS Rail-to-Rail Operational Amplifiers |
| AD8661ARZ | 16V Low Cost, High Performance CMOS Rail-to-Rail Operational Amplifiers |
| AD8661 | 16V Low Cost, High Performance CMOS Rail-to-Rail Operational Amplifiers |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD8655_13 | 制造商:AD 制造商全称:Analog Devices 功能描述:Low Noise, Precision CMOS Amplifier |
| AD8655ARMZ | 功能描述:IC OPAMP GP R-R CMOS 28MHZ 8MSOP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:DigiTrim® 标准包装:2,500 系列:- 放大器类型:通用 电路数:1 输出类型:满摆幅 转换速率:0.11 V/µs 增益带宽积:350kHz -3db带宽:- 电流 - 输入偏压:4nA 电压 - 输入偏移:20µV 电流 - 电源:260µA 电流 - 输出 / 通道:20mA 电压 - 电源，单路/双路(±):2.7 V ~ 36 V，±1.35 V ~ 18 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SO 包装:带卷 (TR) |
| AD8655ARMZ | 制造商:Analog Devices 功能描述:IC OP-AMP 28MHz 11V/ MSOP-8 制造商:Analog Devices 功能描述:IC, OP-AMP, 28MHz, 11V/s, MSOP-8 |
| AD8655ARMZ-R2 | 制造商:Analog Devices 功能描述:OP Amp Single Volt Fdbk R-R I/O 5.5V 8-Pin MSOP T/R 制造商:Analog Devices 功能描述:OP AMP CMOS LOW NOISE 8655 MSOP8 |
| AD8655ARMZ-REEL | 功能描述:IC OPAMP GP R-R CMOS 28MHZ 8MSOP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:DigiTrim® 产品培训模块:Differential Circuit Design Techniques for Communication Applications 标准包装:1 系列:- 放大器类型:RF/IF 差分 电路数:1 输出类型:差分 转换速率:9800 V/µs 增益带宽积:- -3db带宽:2.9GHz 电流 - 输入偏压:3µA 电压 - 输入偏移:- 电流 - 电源:40mA 电流 - 输出 / 通道:- 电压 - 电源，单路/双路(±):3 V ~ 3.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-VQFN 裸露焊盘，CSP 供应商设备封装:16-LFCSP-VQ 包装:剪切带 (CT) 产品目录页面:551 (CN2011-ZH PDF) 其它名称:ADL5561ACPZ-R7CT |
发布紧急采购，3分钟左右您将得到回复。