收藏本站
参数资料
型号： AD9220AR
厂商： ANALOG DEVICES INC
元件分类： ADC
英文描述： Complete 12-Bit 1.5/3.0/10.0 MSPS Monolithic A/D Converters
中文描述： 1-CH 12-BIT FLASH METHOD ADC, PARALLEL ACCESS, PDSO28
封装： MS-013AE, SOIC-28
文件页数： 16/28页
文件大小： 350K
代理商： AD9220AR
AD9221/AD9223/AD9220
REV. D
–16–
degrade slightly as the input common-mode voltage deviates
from its optimum level of 2.5 V.
Alternative AC Interface
Figure 42 shows a flexible ac coupled circuit which can be con-
figured for different input spans. Since the common-mode
voltage of VINA and VINB are biased to midsupply indepen-
dent of VREF, VREF can be pin-strapped or reconfigured to
achieve input spans between 2 V and 5 V p-p. The AD9221/
AD9223/AD9220’s CMRR along with the symmetrical coupling
R-C networks will reject both power supply variations and noise.
The resistors, R, establish the common-mode voltage. They may
have a high value (e.g., 5 k
) to minimize power consumption
and establish a low cutoff frequency. The capacitors, C1
and
C2, are typically a 0.1
μ
F ceramic and 10
μ
F tantalum capacitor
in parallel to achieve a low cutoff frequency while maintaining a
low impedance over a wide frequency range. R
S
isolates the
buffer amplifier from the A/D input. The optimum performance
is achieved when VINA and VINB are driven via Immetrical
networks. The f
–3 dB
point can be approximated by the equation,
f
–3
dB
= 1/(2
×
π
×
R
/2
×
(
C
1 +
C
2))
C2
VINA
VINB
C1
R
+5V
–5V
R
S
V
IN
C1
C2
R
R
S
+5V
R
R
+5V
AD9221/
AD9223/
AD9220
Figure 42. AC-Coupled Input-Flexible Input Span, V
CM
= 2 V
OP AMP SELECTION GUIDE
Op amp selection for the AD9221/AD9223/AD9220 is highly
dependent on a particular application. In general, the perfor-
mance requirements of any given application can be character-
ized by either time domain or frequency domain parameters. In
either case, one should carefully select an op amp which pre-
serves the performance of the A/D. This task becomes challeng-
ing when one considers the AD9221/AD9223/AD9220’s high
performance capabilities coupled with other extraneous system
level requirements such as power consumption and cost.
The ability to select the optimal op amp may be further compli-
cated by either limited power supply availability and/or limited
acceptable
supplies for a desired op amp. Newer, high performance
op amps typically have input and output range limitations in
accordance with their lower supply voltages. As a result, some
op amps will be more appropriate in systems where ac-coupling
is allowable. When dc-coupling is required, op amps without
headroom constraints such as rail-to-rail op amps or ones where
larger supplies can be used should be considered. The following
section describes some op amps currently available from Analog
Devices. The system designer is
always
encouraged to contact
the factory or local sales office to be updated on Analog Devices
latest amplifier product offerings. Highlights of the areas where
the op amps excel and where they may limit the performance of
the AD9221/AD9223/AD9220 is also included.
AD817:
50 MHz Unity GBW, 70 ns Settling to 0.01%, +5 V
to
±
15 V Supplies
Best Applications: Sample Rates < 7 MSPS, Low-
Noise, 5 V p-p Input Range
Limits: THD above 100 kHz
Dual Version of AD817
Best Applications: Differential and/or Low Imped-
ance Input
Drivers, Low Noise
Limits: THD above 100 kHz
130 MHz @ G = +2 BW, 80 ns Settling to 0.01%,
+5 V to
±
15 V Supplies
Best Applications: Sample Rates < 7 MSPS, Low
Noise, 5 V p-p Input Range, Gains
≥
+2
Limits: THD above 100 kHz
Dual Version of AD818
Best Applications: Differential and/or Low Impedance
Input
Drivers, Low Noise, Gains
≥
+2
Limits: THD above 100 kHz
Dual, 145 MHz Unity GBW, Single-Supply Cur-
rent Feedback, +5 V to
±
15 V Supplies
Best Applications: Differential and/or Low Imped-
ance Input Drivers, Sample Rates < 7 MSPS
Limits: THD above 1 MHz
f
–3 dB
= 300 MHz, +5 V or
±
5 V Supplies, Current
Feedback
Best Applications: Single-Supply, AC/DC-Coupled,
Good AC Specs, Low Noise, Low Power (5 mW)
Limits: THD above 5 MHz, Usable Input/Output
Range
Triple, f
–3 dB
= 230 MHz, +5 V or
±
5 V Supplies,
Current Feedback, Disable Function
Best Applications: 3:1 Multiplexer, Good AC Specs
Limits: THD above 5 MHz, Input Range
220 MHz Unity GBW, 16 ns Settling to 0.01%,
±
5 V
Supplies
Best Applications: Best AC Specs, Low Noise, AC-
Coupled
Limits: Usable Input/Output Range, Power
Consumption
130 MHz Unity GBW, 30 ns Settling to 0.01%,
±
5 V Supplies
Best Applications: Good AC Specs, Low Noise,
AC-Coupled
Limits: THD > 5 MHz, Usable Input Range
Rail-to-Rail, 160 MHz Unity GBW, 55 ns Settling
to 0.01%, +5 V Supply, 26 mW
Best Applications: Low Power, Single-Supply Sys-
tems, DC-Coupled, Large Input Range
Limits: Noise with 2 V Input Range
Dual AD8041
Best Applications: Differential and/or Low Imped-
ance Input Drivers
Limits: Noise with 2 V Input Range
AD826:
AD818:
AD828:
AD812:
AD8011:
AD8013:
AD9631:
AD8047:
AD8041:
AD8042:
相关PDF资料
PDF描述
AD9220ARS Complete 12-Bit 1.5/3.0/10.0 MSPS Monolithic A/D Converters
AD9221 Complete 12-Bit 1.5/3.0/10.0 MSPS Monolithic A/D Converters
AD9221AR RES, 18.2K, 1/4, 1%, MF
AD9221ARS Complete 12-Bit 1.5/3.0/10.0 MSPS Monolithic A/D Converters
AD9223 Complete 12-Bit 1.5/3.0/10.0 MSPS Monolithic A/D Converters
相关代理商/技术参数
参数描述
AD9220AR-REEL 功能描述:IC ADC 12BIT 10MSPS 28-SOIC RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极
AD9220ARS 功能描述:IC ADC 12BIT 10MSPS 28-SSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极
AD9220ARS-REEL 功能描述:IC ADC 12BIT 10MSPS 28-SSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极
AD9220ARSZ 功能描述:IC ADC 12BIT 10MSPS 28-SSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6
AD9220ARSZ 制造商:Analog Devices 功能描述:IC ADC 12BIT 10MSPS ((NW)) 制造商:Analog Devices 功能描述:IC, ADC, 12BIT, 10MSPS, SSOP-28
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*