- 您现在的位置：买卖IC网 > PDF目录373960 > AD9224-EB (Analog Devices, Inc.) Complete 12-Bit 40 MSPS Monolithic A/D Converter PDF资料下载
参数资料
| 型号： | AD9224-EB |
| 厂商： | Analog Devices, Inc. |
| 英文描述： | Complete 12-Bit 40 MSPS Monolithic A/D Converter |
| 中文描述： | 完整的12位40 MSPS的单片A / D转换 |
| 文件页数： | 10/24页 |
| 文件大小： | 309K |
| 代理商： | AD9224-EB |
AD9224
–10–
REV. A
REFERENCE OPERATION
The AD9224 contains an onboard bandgap reference that
provides a pin strappable option to generate either a 1 V or 2 V
output. With the addition of two external resistors, the user can
generate reference voltages other than 1 V and 2 V. Another
alternative is to use an external reference for designs requiring
enhanced accuracy and/or drift performance. See Table II for a
summary of the pin-strapping options for the AD9224 refer-
ence configurations.
Figure 16 shows a simplified model of the internal voltage
reference of the AD9224. A pin strappable reference ampli-
fier buffers a 1 V fixed reference. The output from the refer-
ence amplifier, A1, appears on the VREF pin. The voltage on
the VREF pin determines the full-scale input span of the A/D.
This input span equals,
Full-Scale
Input Span
= 2
×
VREF
The voltage appearing at the VREF pin as well as the state of
the internal reference amplifier, A1, are determined by the
voltage appearing at the SENSE pin. The logic circuitry con-
tains two comparators which monitor the voltage at the SENSE
pin. The comparator with the lowest set point (approximately
0.3 V) controls the position of the switch within the feedback
path of A1. If the SENSE pin is tied to AVSS (AGND), the
switch is connected to the internal resistor network thus provid-
ing a VREF of 2.0 V. If the SENSE pin is tied to the VREF pin
via a short or resistor, the switch will connect to the SENSE
pin. This short will provide a VREF of 1.0 V. An external resis-
tor network will provide an alternative VREF between 1.0 V
and 2.0 V. The other comparator controls internal circuitry
that will disable the reference amplifier if the SENSE pin is tied
AVDD. Disabling the reference amplifier allows the VREF pin
to be driven by an external voltage reference.
A2
5k
V
5k
V
5k
V
5k
V
LOGIC
DISABLE
A2
6.25k
V
LOGIC
A1
6.25k
V
DISABLE
A1
1V
TO
A/D
AD9224
CAPT
CAPB
VREF
SENSE
REFCOM
Figure 16. Equivalent Reference Circuit
The actual reference voltages used by the internal circuitry of
the AD9224 appear on the CAPT and CAPB pins. For proper
operation when using the internal or an external reference, it is
necessary to add a capacitor network to decouple these pins.
Figure 17 shows the recommended decoupling network. This
capacitive network performs the following three functions: (1)
along with the reference amplifier, A2, it provides a low source
impedance over a large frequency range to drive the A/D inter-
nal circuitry, (2) it provides the necessary compensation for A2,
and (3) it bandlimits the noise contribution from the reference.
The turn-on time of the reference voltage appearing between
CAPT and CAPB is approximately 15 ms and should be evalu-
ated in any power-down mode of operation.
0.1
m
F
10
m
F
0.1
m
F
0.1
m
F
CAPT
CAPB
AD9224
Figure 17. Recommended CAPT/CAPB Decoupling Network
The A/D’s input span may be varied dynamically by changing
the differential reference voltage appearing across CAPT and
CAPB symmetrically around 2.5 V (i.e., midsupply). To change
the reference at speeds beyond the capabilities of A2, it will be
necessary to drive CAPT and CAPB with two high speed, low
noise amplifiers. In this case, both internal amplifiers (i.e., A1
and A2) must be disabled by connecting SENSE to AVDD,
connecting VREF to AVSS and removing the capacitive decou-
pling network. The external voltages applied to CAPT and
CAPB must be 2.0 V + Input Span/4 and 2.0 V – Input Span/4
respectively in which the input span can be varied between 2 V
and 4 V. Note that those samples within the pipeline A/D dur-
ing any reference transition will be corrupted and should be
discarded.
相关PDF资料 |
PDF描述 |
|---|---|
| AD9225 | Complete 12-Bit, 25 MSPS Monolithic A/D Converter |
| AD9225-EB | Complete 12-Bit, 25 MSPS Monolithic A/D Converter |
| AD9225AR | Complete 12-Bit, 25 MSPS Monolithic A/D Converter |
| AD9225ARS | Complete 12-Bit, 25 MSPS Monolithic A/D Converter |
| AD9226-LQFP-EB | Complete 12-Bit, 65 MSPS ADC Converter |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD9224JR | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog-to-Digital Converter， 12-Bit |
| AD9224JRS | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog-to-Digital Converter， 12-Bit |
| AD9225 | 制造商:Analog Devices 功能描述: |
| AD9225_03 | 制造商:AD 制造商全称:Analog Devices 功能描述:Complete 12-Bit, 25 MSPS Monolithic A/D Converter |
| AD9225AR | 功能描述:IC ADC 12BIT 25MSPS 28-SOIC RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:- 位数:14 采样率（每秒）:83k 数据接口:串行，并联 转换器数目:1 功率耗散（最大）:95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP（0.600"，15.24mm） 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端，双极 |
发布紧急采购，3分钟左右您将得到回复。