- 您现在的位置：买卖IC网 > PDF目录10533 > AD9235BRUZ-65 (Analog Devices Inc)IC ADC 12BIT 65MSPS 28-TSSOP PDF资料下载
参数资料
| 型号： | AD9235BRUZ-65 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 11/40页 |
| 文件大小： | 0K |
| 描述： | IC ADC 12BIT 65MSPS 28-TSSOP |
| 标准包装： | 1 |
| 位数： | 12 |
| 采样率（每秒）： | 65M |
| 数据接口： | 并联 |
| 转换器数目： | 3 |
| 功率耗散（最大）： | 300mW |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 28-TSSOP |
| 包装： | 管件 |
| 输入数目和类型： | 2 个单端，单极；1 个差分，单极 |
| 产品目录页面： | 780 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页
Data Sheet
AD9235
Rev. D | Page 19 of 40
External Reference Operation
The use of an external reference may be necessary to enhance
the gain accuracy of the ADC or to improve thermal drift
characteristics. When multiple ADCs track one another, a single
reference (internal or external) may be necessary to reduce gain
matching errors to an acceptable level. A high precision external
reference may also be selected to provide lower gain and offset
temperature drift. Figure 41 shows the typical drift characteris-
tics of the internal reference in both 1 V and 0.5 V modes.
02461-041
TEMPERATURE (°C)
80
–40 –30 –20 –10
0
10
20
30
40
50
60
70
VREF
ERROR
(%)
1.2
1.0
0.8
0.6
0.4
0.2
0
VREF = 1.0V
VREF = 0.5V
Figure 41. Typical VREF Drift
When the SENSE pin is tied to AVDD, the internal reference is
disabled, allowing the use of an external reference. An internal
reference buffer loads the external reference with an equivalent
7 k load. The internal buffer still generates the positive and
negative full-scale references, REFT and REFB, for the ADC
core. The input span is always twice the value of the reference
voltage; therefore, the external reference must be limited to a
maximum of 1 V.
If the internal reference of the AD9235 is used to drive multiple
converters to improve gain matching, the loading of the refer-
ence by the other converters must be considered. Figure 42
depicts how the internal reference voltage is affected by loading.
02461-042
LOAD (mA)
3.0
0
0.5
1.0
1.5
2.0
2.5
ERROR
(%)
0.05
0
–0.05
–0.10
–0.15
–0.20
–0.25
0.5V ERROR (%)
1V ERROR (%)
Figure 42. VREF Accuracy vs. Load
OPERATIONAL MODE SELECTION
As discussed earlier, the AD9235 can output data in either offset
binary or twos complement format. There is also a provision for
enabling or disabling the clock DCS. The MODE pin is a multi-
level input that controls the data format and DCS state. The
input threshold values and corresponding mode selections are
outlined in Table 8.
Table 8. Mode Selection
MODE Voltage
Data Format
Duty Cycle Stabilizer
AVDD
Twos Complement
Disabled
2/3 AVDD
Twos Complement
Enabled
1/3 AVDD
Offset Binary
Enabled
AGND (Default)
Offset Binary
Disabled
The MODE pin is internally pulled down to AGND by a 20 k
resistor.
TSSOP EVALUATION BOARD
The AD9235 evaluation board provides the support circuitry
required to operate the ADC in its various modes and configu-
rations. The converter can be driven differentially, through an
AD8138 driver or a transformer, or single-ended. Separate pow-
er pins are provided to isolate the DUT from the support cir-
cuitry. Each input configuration can be selected by proper con-
nection of various jumpers (refer to the schematics). Figure 43
shows the typical bench characterization setup used to evaluate
the ac performance of the AD9235. It is critical that signal
sources with very low phase noise (<1 ps rms jitter) be used to
realize the ultimate performance of the converter. Proper filter-
ing of the input signal, to remove harmonics and lower the inte-
grated noise at the input, is also necessary to achieve the speci-
fied noise performance.
The AUXCLK input should be selected in applications requiring
the lowest jitter and SNR performance, i.e., IF undersampling
characterization. It allows the user to apply a clock input signal
that is 4× the target sample rate of the AD9235. A low-jitter,
differential divide-by-4 counter, the MC100LVEL33D, provides
a 1× clock output that is subsequently returned back to the CLK
input via JP9. For example, a 260 MHz signal (sinusoid) is
divided down to a 65 MHz signal for clocking the ADC. Note
that R1 must be removed with the AUXCLK interface. Lower
jitter is often achieved with this interface since many RF signal
generators display improved phase noise at higher output
frequencies and the slew rate of the sinusoidal output signal is
4× that of a 1× signal of equal amplitude.
Complete schematics and layout plots follow and demonstrate
the proper routing and grounding techniques that should be
applied at the system level.
相关PDF资料 |
PDF描述 |
|---|---|
| VE-J3Z-MY-F1 | CONVERTER MOD DC/DC 2V 20W |
| MS3102A22-16S | CONN RCPT 9POS BOX MNT W/SCKT |
| VE-J3Z-MX-F2 | CONVERTER MOD DC/DC 2V 30W |
| AMIS30663CANG2G | TRANSCEIVER CAN HS 3.3V 8-SOIC |
| VI-B4T-MX-F2 | CONVERTER MOD DC/DC 6.5V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD9235BRUZ-65 | 制造商:Analog Devices 功能描述:IC 12-BIT ADC |
| AD9235BRUZRL7-20 | 功能描述:IC ADC 12BIT SGL 20MSPS 28TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| AD9235BRUZRL7-40 | 功能描述:IC ADC 12BIT SGL 40MSPS 28TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
| AD9235BRUZRL7-65 | 功能描述:IC ADC 12BIT SGL 65MSPS 28TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
| AD9235XCP-65 | 制造商:Analog Devices 功能描述:12-BIT 3V 20 MSPS ADC - Bulk |
发布紧急采购，3分钟左右您将得到回复。